ST Nucleo G031K8

Overview

The STM32 Nucleo-32 board provides an affordable and flexible way for users to try out new concepts and build prototypes by choosing from the various combinations of performance and power consumption features, provided by the STM32 microcontroller.

The Arduino™ Nano V3 connectivity support allows the easy expansion of the functionality of the STM32 Nucleo open development platform with a wide choice of specialized shields.

The STM32 Nucleo-32 board does not require any separate probe as it integrates the ST-LINK debugger/programmer.

The STM32 Nucleo-32 board comes with the STM32 comprehensive free software libraries and examples available with the STM32Cube MCU Package.

Nucleo G031K8

More information about the board can be found at the Nucleo G031K8 website [1].

Hardware

Nucleo G031K8 provides the following hardware components:

  • STM32 microcontroller in 32-pin package featuring 64 Kbytes of Flash memory and 8 Kbytes of SRAM.

  • Extension resource:

    • Arduino* Nano V3 connectivity

  • On-board ST-LINK/V2-1 debugger/programmer with SWD connector:

  • Flexible board power supply:

    • USB VBUS or external source (3.3V, 5V, 7 - 12V)

    • Current consumption measurement (IDD)

  • Four LEDs:

    • USB communication (LD1), power LED (LD2), user LED (LD3), USB power fault LED (LD4)

  • One push-button: RESET

  • USB re-enumeration capability. Three different interfaces supported on USB:

    • Virtual COM port

    • Mass storage

    • Debug port

More information about STM32G031K8 can be found in the STM32G0x1 reference manual [2]

Supported Features

The Zephyr nucleo_g031k8 board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

UART

on-chip

serial port-polling; serial port-interrupt

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

CLOCK

on-chip

reset and clock control

I2C

on-chip

i2c controller

SPI

on-chip

spi controller

Other hardware features are not yet supported in this Zephyr port.

The default configuration can be found in the defconfig file: boards/arm/nucleo_g031k8/nucleo_g031k8_defconfig

Connections and IOs

Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as input (with or without pull-up or pull-down), or as peripheral alternate function. Most of the GPIO pins are shared with digital or analog alternate functions. All GPIOs are high current capable except for analog inputs.

Default Zephyr Peripheral Mapping:

  • UART_2 TX/RX : PA2/PA3 (ST-Link Virtual Port Com)

  • I2C2 SCL/SDA : PA9/PA10 (Arduino I2C)

  • SPI1 SCK/MISO/MOSI : PB3/PB4/PB5 (Arduino SPI)

  • LD3 : PC6

For mode details please refer to STM32 Nucleo-32 board User Manual [3].

Programming and Debugging

Applications for the nucleo_g031k8 board configuration can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Flashing

Nucleo G031K8 board includes an ST-LINK/V2-1 embedded debug tool interface. This interface is supported by the openocd version included in the Zephyr SDK.

Flashing an application to Nucleo G031K8

Here is an example for the Blinky application.

# From the root of the zephyr repository
west build -b nucleo_g031k8 samples/basic/blinky
west flash

You will see the LED blinking every second.

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b nucleo_g031k8 samples/hello_world
west debug

Restriction

On some boards, the board reset line is not used by the controller. Therefore the reset button, reset-pin and the ST-Link reset have no effect. To enable those functionalities, the option byte NRST_mode in the User Configuration needs to be changed from 2 to 1 or 3 - depending on the requirements.

References