Actinius Icarus

Overview

Icarus IoT Dev Board

Icarus IoT Dev Board (nRF9160 Feather)

The Icarus is a cost-effective cellular IoT board in Adafruit’s Feather/FeatherWing form factor. It is built around Nordic Semi’s nRF9160 modem and combines LTE-M, NB-IoT, GPS, accelerometer, USB, LiPo charger as well as an eSIM and a nano SIM connector.

The main uController is the Nordic Semiconductor nRF9160, with ARM Cortex-M33F CPU, ARMv8-M Security Extension and the following devices (provided directly by Nordic):

  • ADC

  • CLOCK

  • FLASH

  • GPIO

  • I2C

  • MPU

  • NVIC

  • PWM

  • RTC

  • Segger RTT (RTT Console)

  • SPI

  • UARTE

  • WDT

  • IDAU

Hardware

The detailed information about the on-board hardware can be found at the Icarus Product Website [2].

Icarus IoT Dev Board w/ Pinouts

Icarus IoT Dev Board w/ Pinouts

Pin description

External Pins available to user:

Icarus pin

Function

Description

Device-tree node

RST

Reset

Active low reset with internal pullup

3.3V

Power output

Main 3.3 V supply

NC

Not connected

GND

Power output

Ground

14 / A1

GPIO / Analog in

nRF9160 P0.14 / AIN1

gpio0 / adc_1

15 / A2

GPIO / Analog in

nRF9160 P0.15 / AIN2

gpio0 / adc_2

16 / A3

GPIO / Analog in

nRF9160 P0.16 / AIN3

gpio0 / adc_3

17 / A4

GPIO / Analog in

nRF9160 P0.17 / AIN4

gpio0 / adc_4

18 / A5

GPIO / Analog in

nRF9160 P0.18 / AIN5

gpio0 / adc_5

19 / A6

GPIO / Analog in

nRF9160 P0.19 / AIN6

gpio0 / adc_6

20 / SCK

GPIO / SPI pin

nRF9160 P0.20 / SPI SCK pin

gpio0 / spi3

21 / MOSI

GPIO / SPI pin

nRF9160 P0.21 / SPI MOSI pin

gpio0 / spi3

22 / MISO

GPIO / SPI pin

nRF9160 P0.22 / SPI MISO pin

gpio0 / spi3

23 / RX

GPIO / UART pin

nRF9160 P0.23 / UART RX pin

gpio0 / uart1

24 / TX

GPIO / UART pin

nRF9160 P0.24 / UART TX pin

gpio0 / uart1

VIN

Power input

Voltage input (maximum 10.2 V)

VBAT

Power input

Battery voltage input

EN

Power enable

Power enable pin (pull low to disable power)

USB

Power input

USB voltage input

gpio0

4

GPIO

nRF9160 P0.04

gpio0

3

GPIO

nRF9160 P0.03

gpio0

2

GPIO

nRF9160 P0.02

gpio0

1

GPIO

nRF9160 P0.01

gpio0

0

GPIO

nRF9160 P0.00

gpio0

30

GPIO

nRF9160 P0.30

gpio0

31

GPIO

nRF9160 P0.31

gpio0

SCL

GPIO / I2C pin

nRF9160 P0.26 / I2C SCL pin

gpio0 / i2c2

SDA

GPIO / I2C pin

nRF9160 P0.27 / I2C SDA pin

gpio0 / i2c2

nRF9160 pins connected internally:

nRF9160 pin

Function

Device-tree node

P0.05

User button

button0

P0.10

Red LED

led0 / pwm-led0

P0.11

Green LED

led1 / pwm-led1

P0.12

Blue LED

led2 / pwm-led2

P0.28

Accelerometer Interrupt 1

lis2dh12-accel

P0.29

Accelerometer Interrupt 2

lis2dh12-accel

P0.08

SIM select pin

gpio0

P0.13 / AIN0

Battery voltage measurement

adc_0

P0.06

USB - FTDI serial RX

uart0

P0.09

USB - FTDI serial TX

uart0

P0.07

USB - FTDI serial RTS Charger enable pin (Icarus v2.0)

uart0 gpio0 (Icarus v2.0)

P0.25

USB - FTDI serial CTS FLASH memory SPI CS pin (Icarus v2.0)

uart0 gpio0 (Icarus v2.0)

Supported Features

The actinius_icarus board configuration supports the following hardware features:

Interface

Controller

Driver/Component

ADC

on-chip

adc

CLOCK

on-chip

clock_control

FLASH

on-chip

flash

GPIO

on-chip

gpio

I2C(M)

on-chip

i2c

MPU

on-chip

arch/arm

NVIC

on-chip

arch/arm

PWM

on-chip

pwm

SPI(M/S)

on-chip

spi

SPU

on-chip

system protection

UARTE

on-chip

serial

ACCEL

st

lis2dh

SIM Selection

The SIM choice (eSIM or nano-SIM) can be configured in Devicetree by adjusting the sim property in the sim_select node.

Charger Enable/Disable

Since hardware version 2.0 the charger can be disabled by adjusting the charger property of the charger_enable device tree node.

Security components

  • Implementation Defined Attribution Unit (IDAU [1]). The IDAU is implemented with the System Protection Unit and is used to define secure and non-secure memory maps. By default, all of the memory space (Flash, SRAM, and peripheral address space) is defined to be secure accessible only.

  • Secure boot.

Building Secure/Non-Secure Zephyr applications

The process requires the following steps:

  1. Build the Secure Zephyr application using -DBOARD=actinius_icarus and CONFIG_TRUSTED_EXECUTION_SECURE=y in the application project configuration file.

  2. Build the Non-Secure Zephyr application using -DBOARD=actinius_icarus_ns.

  3. Merge the two binaries together.

If you are using Segger Embedded Studio v4.18 or later, the two binaries are built, merged, and burned automatically, unless you have disabled the feature.

When building a Secure/Non-Secure application, the Secure application will have to set the IDAU (SPU) configuration to allow Non-Secure access to all CPU resources utilized by the Non-Secure application firmware. SPU configuration shall take place before jumping to the Non-Secure application.

More information can be found in the Icarus “Get Started” Guide [3] or the Actinius Documentation Portal [4].

References