ST STM32H747I Discovery

Overview

The discovery kit enables a wide diversity of applications taking benefit from audio, multi-sensor support, graphics, security, video, and high-speed connectivity features.

The board includes an STM32H747XI SoC with a high-performance DSP, Arm Cortex-M7 + Cortex-M4 MCU, with 2MBytes of Flash memory, 1MB RAM, 480 MHz CPU, Art Accelerator, L1 cache, external memory interface, large set of peripherals, SMPS, and MIPI-DSI.

Additionally, the board features:

  • On-board ST-LINK/V3E supporting USB reenumeration capability

  • USB ST-LINK functions: virtual COM port, mass storage, debug port

  • Flexible power-supply options:

    • ST-LINK USB VBUS, USB OTG HS connector, or external sources

  • 4” capacitive touch LCD display module with MIPI® DSI interface

  • Ethernet compliant with IEEE802.3-2002

  • USB OTG HS

  • Stereo speaker outputs

  • ST-MEMS digital microphones

  • 256-Mbit SDRAM

  • 4 color user LEDs

  • 1 user and reset push-button

  • 4-direction joystick with selection button

  • Arduino Uno V3 connectors

STM32H747I-DISCO

More information about the board can be found at the STM32H747I-DISCO website. More information about STM32H747XIH6 can be found here:

Supported Features

The current Zephyr stm32h747i_disco board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

UART

on-chip

serial port-polling; serial port-interrupt

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

FLASH

on-chip

flash memory

ETHERNET

on-chip

ethernet (*)

RNG

on-chip

True Random number generator

FMC

on-chip

memc (SDRAM)

SPI

on-chip

spi

SDMMC

on-chip

disk access

IPM

on-chip

virtual mailbox based on HSEM
(*) From UM2411 Rev 4:

With the default setting, the Ethernet feature is not working because of a conflict between ETH_MDC and SAI4_D1 of the MEMs digital microphone. Make sure you have SB8 closed and SB21 open to get Ethernet working.

Other hardware features are not yet supported on Zephyr porting.

The default configuration per core can be found in the defconfig files: boards/arm/stm32h747i_disco/stm32h747i_disco_defconfig_m7 and boards/arm/stm32h747i_disco/stm32h747i_disco_defconfig_m4

Pin Mapping

STM32H747I Discovery kit has 9 GPIO controllers. These controllers are responsible for pin muxing, input/output, pull-up, etc.

For mode details please refer to STM32H747I-DISCO website.

Default Zephyr Peripheral Mapping:

  • UART_1 TX/RX : PA9/PA10 (ST-Link Virtual Port Com)

  • UART_8 TX/RX : PJ8/PJ9 (Arduino Serial)

  • SPI_5 NSS/SCK/MISO/MOSI : PK1/PK0/PJ11/PJ10 (Arduino SPI)

  • SDMMC_1 D0/D1/D2/D3/CK/CMD: PC8/PC9/PC10/PC11/PC12/PD2

  • LD1 : PI12

  • LD2 : PI13

  • LD3 : PI14

  • LD4 : PI15

  • W-UP : PC13

  • J-CENTER : PK2

  • J-DOWN : PK3

  • J-LEFT : PK4

  • J-RIGHT : PK5

  • J-UP : PK6

System Clock

The STM32H747I System Clock can be driven by an internal or external oscillator, as well as by the main PLL clock. By default, the CPU1 (Cortex-M7) System clock is driven by the PLL clock at 400MHz, and the CPU2 (Cortex-M4) System clock is driven at 200MHz. PLL clock is feed by a 25MHz high speed external clock.

Serial Port

The STM32H747I Discovery kit has up to 8 UARTs. Default configuration assigns USART1 and UART8 to the CPU1. The Zephyr console output is assigned to UART1 which connected to the onboard ST-LINK/V3.0. Virtual COM port interface. Default communication settings are 115200 8N1.

Ethernet

Disclaimer: This section is mostly copy-paste of corresponding DISCO_H747I modifications for Ethernet mbed blog post. The author of this article sincerely allowed to use the images and his knowledge about necessary HW modifications to get Ethernet working with this board.

To get Ethernet working following HW modifications are required:

  • SB21, SB45 and R87 should be opened

  • SB22, SB44, SB17 and SB8 should be closed

Following two images shows necessary changes on the board marked:

STM32H747I-DISCO - Ethernet modification 1 (**SB44**, **SB45**) STM32H747I-DISCO - Ethernet modification 2 (**SB21**, **R87**, **SB22**, **SB17** and **SB8**)

Resources sharing

The dual core nature of STM32H747 SoC requires sharing HW resources between the two cores. This is done in 3 ways:

  • Compilation: Clock configuration is only accessible to M7 core. M4 core only has access to bus clock activation and deactivation.

  • Static pre-compilation assignment: Peripherals such as a UART are assigned in devicetree before compilation. The user must ensure peripherals are not assigned to both cores at the same time.

  • Run time protection: Interrupt-controller and GPIO configurations could be accessed by both cores at run time. Accesses are protected by a hardware semaphore to avoid potential concurrent access issues.

Programming and Debugging

Applications for the stm32h747i_disco board should be built per core target, using either stm32h747i_disco_m7 or `stm32h747i_disco_m4 as the target. See Building an Application for more information about application builds.

Note

If using OpenOCD you will need a recent development version as the last official release does not support H7 dualcore yet. Also, with OpenOCD, sometimes, flashing is not working. It is necessary to erase the flash (with STM32CubeProgrammer for example) to make it work again. Debugging with OpenOCD is currently working for this board only with Cortex M7, not Cortex M4.

Flashing

Flashing operation will depend on the target to be flashed and the SoC option bytes configuration. It is advised to use STM32CubeProgrammer to check and update option bytes configuration and flash stm32h747i_disco_m7 and stm32h747i_disco_m4 targets.

By default:

  • CPU1 (Cortex-M7) boot address is set to 0x80000000 (OB: BOOT_CM7_ADD0)

  • CPU2 (Cortex-M4) boot address is set to 0x81000000 (OB: BOOT_CM4_ADD0)

Also, default out of the box board configuration enables CM7 and CM4 boot when board is powered (Option bytes BCM7 and BCM4 are checked). It is possible to change Option Bytes so that CM7 boots first in stand alone, and CM7 will wakeup CM4 after clock initialization. Drivers are able to take into account both Option Bytes configurations automatically.

Zephyr flash configuration has been set to meet these default settings.

Flashing an application to STM32H747I M7 Core

First, connect the STM32H747I Discovery kit to your host computer using the USB port to prepare it for flashing. Then build and flash your application.

Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b stm32h747i_disco_m7 samples/hello_world

Use the following commands to flash either m7 or m4 target:

$ ./STM32_Programmer_CLI -c port=SWD mode=UR -w <path_to_m7_binary>  0x8000000
$ ./STM32_Programmer_CLI -c port=SWD mode=UR -w <path_to_m4_binary>  0x8100000

Alternatively it is possible to flash with OpenOcd but with some restrictions: Sometimes, flashing is not working. It is necessary to erase the flash (with STM32CubeProgrammer for example) to make it work again. Debugging with OpenOCD is currently working for this board only with Cortex M7, not Cortex M4.

# From the root of the zephyr repository
west build -b stm32h747i_disco_m7 samples/hello_world
west flash

Run a serial host program to connect with your board:

$ minicom -D /dev/ttyACM0

You should see the following message on the console:

Hello World! stm32h747i_disco_m7

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b stm32h747i_disco_m7 samples/hello_world
west debug