Particle Xenon

Overview

The Particle Xenon is a low-cost mesh-enabled development board based on the Nordic Semiconductor nRF52840 SoC. The board was developed by Particle Industries and has an SWD connector on it for programming.

It is equipped with a onboard LIPO circuit and conforms to the Adafruit Feather formfactor.

The Particle Xenon board provides support for the Nordic Semiconductor nRF52840 ARM® Cortex®-M4F SoC with an integrated 2.4 GHz transceiver supporting Bluetooth® Low Energy and IEEE® 802.15.4.

For more information about the Particle Xenon board:

Hardware

On the front of the board are RGB-LED, LED and LIPO circuitry. The RGB-LED is controlled by the nRF52840 via GPIO pins.

Fig. 133 Particle Xenon (Credit: Particle Industries)

Power supply

The board is optimized for low power applications and supports two power source configurations, battery and micro USB connector.

It contains circuitry for LIPO usage and can be charged via the USB port.

Supported Features

The particle_xenon board configuration supports the following hardware features:

Interface	Controller	Driver/Component
NVIC	on-chip	nested vectored interrupt controller
RTC	on-chip	system clock
UART	on-chip	serial port
I2C	on-chip	i2c
SPI	on-chip	spi
GPIO	on-chip	gpio
FLASH	on-chip	flash
RADIO	on-chip	Bluetooth

Other hardware features are not supported by the Zephyr kernel.

Connections and IOs

Please see the Xenon Datasheet for header pin assignments, which are common to all Feather-compatible Particle boards. Some peripherals are available to applications through DTS overlay include directives:

mesh_feather_i2c1_twi1.dtsi exposes TWI1 on labeled Feather SDA1/SCL1 pins
mesh_feather_spi_spi1.dtsi exposes SPI1 on labeled Feather SPI pins
mesh_feather_spi_spi3.dtsi exposes SPI3 on labeled Feather SPI pins
mesh_feather_spi1_spi3.dtsi exposes SPI3 on labeled Feather SPI1 pins
mesh_feather_uart1_rtscts.dtsi adds hardware flow control to labeled Feather UART pins
mesh_xenon_uart2.dtsi exposes UARTE1 on labeled Feather UART2 pins

LED

LED0 (blue)
LED1 (red)
LED2 (green)
LED3 (blue)

Push buttons

SW0 via MODE
SW1 via RESET

I2C

TWI0 enabled on labeled header (SDA/SCL)
TWI1 selectable with overlay (SDA1/SCL1)

SPI

SPI0 disabled due to TWI0 conflict
SPI1 selectable with overlay (SPI)
SPI2 internal to 32 Mb CFI flash chip
SPI3 selectable with overlay (SPI or SPI1)

UART

UARTE0 enabled RX/TX on labeled header (UART1); add RTS/CTS with overlay
UARTE1 selectable with overlay (UART2)

Programming and Debugging

Applications for the particle_xenon board configuration can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Flashing

Build and flash an application in the usual way, for example:

# From the root of the zephyr repository
west build -b particle_xenon samples/basic/blinky
west flash

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b particle_xenon samples/hello_world
west debug

Testing the LEDs and buttons

There are 2 samples that allow you to test that the buttons (switches) and LEDs on the board are working properly with Zephyr:

You can build and flash the examples to make sure Zephyr is running correctly on your board.