Bluetooth: Mesh light

The Bluetooth mesh light sample demonstrates how to set up a basic mesh server model application, and control LEDs with the Bluetooth mesh using the Generic OnOff models.

Note

This sample is self-contained, and can be tested on its own. However, it is required when testing the Bluetooth: Mesh light switch sample.

Overview

This sample is split into two source files:

  • A main.c file to handle initialization.

  • One additional file for handling mesh models, model_handler.c.

After provisioning and configuring the mesh models supported by the sample in the nRF Mesh mobile app, you can control the LEDs on the development kit from the app.

Models

The following table shows the mesh light composition data for this sample:

Element 1

Element 2

Element 3

Element 4

Config Server

Gen. OnOff Server

Gen. OnOff Server

Gen. OnOff Server

Health Server

Gen. OnOff Server

The models are used for the following purposes:

  • Generic OnOff Server instances in elements 1 to 4 each control LEDs 1 to 4, respectively.

  • Config Server allows configurator devices to configure the node remotely.

  • Health Server provides attention callbacks that are used during provisioning to call your attention to the device. These callbacks trigger blinking of the LEDs.

The model handling is implemented in src/model_handler.c, which uses the DK Button and LEDs library to control each LED on the development kit according to the matching received messages of Generic OnOff Server.

Requirements

The sample supports the following development kits:

Hardware platforms

PCA

Board name

Build target

nRF5340 DK

PCA10095

nrf5340dk_nrf5340

nrf5340dk_nrf5340_cpuapp

nrf5340dk_nrf5340_cpuappns

nRF52840 DK

PCA10056

nrf52840dk_nrf52840

nrf52840dk_nrf52840

nRF52 DK

PCA10040

nrf52dk_nrf52832

nrf52dk_nrf52832

nRF52833 DK

PCA10010

nrf52833dk_nrf52833

nrf52833dk_nrf52833

nRF52833 DK (emulating nRF52820)

PCA10100

nrf52833dk_nrf52820

nrf52833dk_nrf52820

The sample also requires a smartphone with Nordic Semiconductor’s nRF Mesh mobile app installed in one of the following versions:

User interface

Buttons:

Can be used to input the OOB authentication value during provisioning. All buttons have the same functionality during this procedure.

LEDs:

Show the OOB authentication value during provisioning if the “Push button” OOB method is used. Show the OnOff state of the Generic OnOff Server of the corresponding element.

Building and running

This sample can be found under samples/bluetooth/mesh/light in the nRF Connect SDK folder structure.

See Building and programming a sample application for information about how to build and program the application.

Testing

After programming the sample to your development kit, you can test it by using a smartphone with Nordic Semiconductor’s nRF Mesh app installed. Testing consists of provisioning the device and configuring it for communication with the mesh models.

Provisioning the device

The provisioning assigns an address range to the device, and adds it to the mesh network. Complete the following steps in the nRF Mesh app:

  1. Tap Add node to start scanning for unprovisioned mesh devices.

  2. Select the Mesh Light device to connect to it.

  3. Tap Identify, and then Provision, to provision the device.

  4. When prompted, select an OOB method and follow the instructions in the app.

Once the provisioning is complete, the app returns to the Network screen.

Configuring models

See Configuring mesh models using the nRF Mesh mobile app for details on how to configure the mesh models with the nRF Mesh mobile app.

Configure the Generic OnOff Server model on each element on the Mesh Light node:

  • Bind the model to Application Key 1.

    Once the model is bound to the application key, you can control the first LED on the device.

  • In the model view, tap ON (one of the Generic On Off Controls) to light up the first LED on the development kit.

Make sure to complete the configuration on each of the elements on the node to enable controlling each of the remaining three LEDs.

Dependencies

This sample uses the following nRF Connect SDK libraries:

In addition, it uses the following Zephyr libraries: