ARM V2M Musca-S1

Overview

The v2m_musca_s1 board configuration is used by Zephyr applications that run on the V2M Musca-S1 board. It provides support for the Musca-S1 ARM Cortex-M33 CPU and the following devices:

  • Nested Vectored Interrupt Controller (NVIC)

  • System Tick System Clock (SYSTICK)

  • Cortex-M System Design Kit GPIO

  • Cortex-M System Design Kit UART

ARM V2M Musca-S1

More information about the board can be found at the V2M Musca-S1 Website.

Hardware

ARM V2M MUSCA-S1 provides the following hardware components:

  • ARM Cortex-M33 (with FPU and DSP)

  • ARM IoT Subsystem for Cortex-M33

  • Memory

    • 512KB on-chip system memory SRAM.

    • 2MB on-chip eMRAM (non-volatile).

    • 32MB of external QSPI flash.

  • Debug

    • JTAG, SWD & P-JTAG.

    • DAPLink with a virtual UART port.

  • Arduino interface

    • 16 3V3 or 1V8 GPIO.

    • UART.

    • SPI.

    • I2C.

    • I2S.

    • 3-channel PWM.

    • 6-channel analog interface.

  • On-board Peripherals

    • User RGB LED.

    • Gyro sensor.

    • Combined ADC/DAC/temperature sensor.

User push buttons

The v2m_musca_s1 board provides the following user push buttons:

  • PBON: power on/off.

  • nSRST: Cortex-M33 system reset and CoreSight debug reset.

  • ISP: Updates DAPLink firmware.

Supported Features

The v2m_musca_s1 board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

SYSTICK

on-chip

systick

UART

on-chip

serial port-polling; serial port-interrupt

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

TIMER

on-chip

timer

TrustZone

on-chip

Trusted Firmware-M

Other hardware features are not currently supported by the port. See the V2M Musca-S1 Website for a complete list of V2M Musca-S1 board hardware features.

The default configuration can be found in the defconfig file: boards/arm/v2m_musca_s1/v2m_musca_s1_defconfig.

Interrupt Controller

Musca-S1 is a Cortex-M33 based SoC and has 15 fixed exceptions and 77 IRQs.

A Cortex-M33-based board uses vectored exceptions. This means each exception calls a handler directly from the vector table.

Zephyr provides handlers for exceptions 1-7, 11, 12, 14, and 15, as listed in the following table:

Exc#

Name

Remarks

Used by Zephyr Kernel

1

Reset

system initialization

2

NMI

system fatal error

3

Hard fault

system fatal error

4

MemManage

MPU fault

system fatal error

5

Bus

system fatal error

6

Usage fault

Undefined instruction, or switch attempt to ARM mode

system fatal error

7

SecureFault

Unauthorized access to secure region from ns space

system fatal error

8

Reserved

not handled

9

Reserved

not handled

10

Reserved

not handled

11

SVC

system calls, kernel run-time exceptions, and IRQ offloading

12

Debug monitor

system fatal error

13

Reserved

not handled

14

PendSV

context switch

15

SYSTICK

system clock

16

Reserved

not handled

17

Reserved

not handled

18

Reserved

not handled

Pin Mapping

The ARM V2M Musca-S1 board’s GPIO controller is responsible for pin-muxing, input/output, pull-up, etc. All GPIO controller pins are exposed via pins 0 - 15.

Mapping from the ARM V2M Musca-S1 Board pins to GPIO controller pins:

  • D0 : P0_0

  • D1 : P0_1

  • D2 : P0_2

  • D3 : P0_3

  • D4 : P0_4

  • D5 : P0_5

  • D6 : P0_6

  • D7 : P0_7

  • D8 : P0_8

  • D9 : P0_9

  • D10 : P0_10

  • D11 : P0_11

  • D12 : P0_12

  • D13 : P0_13

  • D14 : P0_14

  • D15 : P0_15

Peripheral Mapping:

  • UART_0_RX : D0

  • UART_0_TX : D1

  • SPI_0_CS : D10

  • SPI_0_MOSI : D11

  • SPI_0_MISO : D12

  • SPI_0_SCLK : D13

  • I2C_0_SDA : D14

  • I2C_0_SCL : D15

For mode details please refer to Musca-S1 Technical Reference Manual (TRM).

RGB LED

Musca-S1 has a built-in RGB LED connected to GPIO[4:2] pins.

  • Red LED connected at GPIO[2] pin,with optional PWM0.

  • Green LED connected at GPIO[3] pin,with optional PWM1.

  • Blue LED connected at GPIO[4] pin,with optional PWM2.

Note

The SCC registers select the functions of pins GPIO[4:2].

System Clock

V2M Musca-S1 has a 32.768kHz crystal clock. The clock goes to a PLL and is multiplied to drive the Cortex-M33 processors and SSE-200 subsystem. The default is 50MHz but can be increased to 200MHz maximum for the secondary processor (CPU1) via software configuration. The maximum clock frequency for the primary processor (CPU0) is 50MHz.

Serial Port

The ARM Musca-S1 processor has two UARTs. Both the UARTs have only two wires for RX/TX and no flow control (CTS/RTS) or FIFO. The Zephyr console output, by default, uses UART1.

Security components

  • Implementation Defined Attribution Unit (IDAU). The IDAU is used to define secure and non-secure memory maps. By default, all of the memory space is defined to be secure accessible only.

  • Secure and Non-secure peripherals via the Peripheral Protection Controller (PPC). Peripherals can be assigned as secure or non-secure accessible.

  • Secure boot.

  • Secure AMBA® interconnect.

Serial Configuration Controller (SCC)

The ARM Musca-S1 test chip implements a Serial Configuration Control (SCC) register. The purpose of this register is to allow individual control of clocks, reset-signals and interrupts to peripherals, and pin-muxing.

Boot memory

Normal Musca-S1 test chip boot operation is from 2MB eMRAM by default, and it offers the fastest boot method. Musca-S1 test chip also support to boot from 32MB off-chip QSPI flash. You can update the DAPLink firmware and set the boot selector slider switch for either QSPI or eMRAM for booting.

Programming and Debugging

Musca-S1 supports the v8m security extension, and by default boots to the secure state.

When building a secure/non-secure application, the secure application will have to set the IDAU/SAU and MPC configuration to permit access from the non-secure application before jumping.

The following system components are required to be properly configured during the secure firmware:

  • AHB5 TrustZone Memory Protection Controller (MPC).

  • AHB5 TrustZone Peripheral Protection Controller (PPC).

  • Implementation-Defined Attribution Unit (IDAU).

For more details please refer to Corelink SSE-200 Subsystem.

Flashing

Building a secure only application

You can build applications in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b v2m_musca_s1 samples/hello_world

Open a serial terminal (minicom, putty, etc.) with the following settings:

  • Speed: 115200

  • Data: 8 bits

  • Parity: None

  • Stop bits: 1

Uploading an application to V2M Musca-S1

To upload the Hello World application to the board, no extra steps are required. You can directly upload build/zephyr/zephyr.hex, which is generated by Zephyr’s build system.

In other situations, applications must first be converted to Intel’s hex format before being flashed to a V2M Musca-S1. An optional bootloader can also be prepended to the image.

The eMRAM base address alias is 0xA000000, and the QSPI flash base address alias is 0x0. The image offset is calculated by adding the flash offset to the bootloader partition size (when there is one).

A third-party tool (srecord) can be used to concatenate the images and generate the Intel formatted hex image.

For more information refer to the Srecord Manual.

srec_cat $BIN_BOOLOADER -Binary -offset $FLASH_OFFSET $BIN_APP -Binary -offset $IMAGE_OFFSET -o zephyr.hex -Intel

# For a 128K bootloader IMAGE_OFFSET = $FLASH_OFFSET + 0x20000
srec_cat $BIN_BOOLOADER -Binary -offset 0xA000000 $BIN_APP -Binary -offset 0xA020000 -o zephyr.hex -Intel
The Musca-S1 with the USB connected and powered-on

To upload the application, connect the V2M Musca-S1 to your host computer using the USB port and power-on the board by pressing the PBON button as seen on the picture above. The 3 LEDs should be lit (PWR, ON and 5VON) and you should see a USB connection exposing a Mass Storage (MUSCA_S) and a USB Serial Port. Now copy the generated zephyr.hex to the MUSCA_S drive.

Reset the board, and if you were building the hello_world application you should see the following message on the corresponding serial port:

Musca-S1 Dual Firmware Version 1.9
*** Booting Zephyr OS build zephyr-v2.4.0-2314-gadc81d188323  ***
Hello World! musca_s1

Building a secure/non-secure image with Trusted Firmware-M

The process requires five steps:

  1. Build Trusted Firmware-M (TF-M).

  2. Import it as a library to the Zephyr source folder.

  3. Build Zephyr with a non-secure configuration.

  4. Merge the two binaries together and sign them.

  5. Concatenate the bootloader with the signed image blob.

In order to build tfm please refer to Trusted Firmware-M Guide. Follow the build steps for AN521 target while replacing the platform with -DTFM_PLATFORM=musca_s1 and compiler (if required) with -DTFM_TOOLCHAIN_FILE=toolchain_GNUARM.cmake.

Copy over TF-M as a library to the Zephyr project source and create a shortcut for the secure veneers and necessary header files. All files are in the install folder after TF-M built.

Building the TF-M integration sample for Musca-S1

The TF-M integration samples can be run using the v2m_musca_s1_nonsecure target. Please make sure all the requirements listed in the sample’s description are met before building.

# From the root of the zephyr repository
west build -b v2m_musca_s1_nonsecure samples/tfm_integration/psa_level_1

To upload the build artifact to the board, first connect the Musca-S1 to your computer using the USB port, press the PBON button, and copy the build/tfm_zephyr.hex file onto the MUSCA_S mass storage device. (For a more detailed description of these steps, please read the ‘Uploading an application to V2M Musca-S1’ section.)

Once the file transfer has completed, you may reset the board.

The tfm_zephyr.hex file was generated by concatenating the signed TF-M and Zephyr binaries with the MCUboot image, and converting it to Intel’s hex format. These steps are all performed automatically by CMake.

For alternative build options and more information, please read the corresponding TF-M integration example’s README file.