NXP MIMXRT1024-EVK¶

Overview¶

The i.MX RT1024 expands the i.MX RT crossover processor families by providing high-performance feature set in low-cost LQFP packages, further simplifying board design and layout for customers. The i.MX RT1024 runs on the Arm® Cortex®-M7 core at 500 MHz.

Hardware¶

MIMXRT1024DAG5A MCU (600 MHz, 256 KB on-chip memory, 4096KB on-chip QSPI flash)
Memory
- 256 Mbit SDRAM
- 64 Mbit QSPI Flash
- TF socket for SD card
Connectivity
- 10/100 Mbit/s Ethernet PHY
- Micro USB host and OTG connectors
- CAN transceivers
- Arduino interface
Audio
- Audio Codec
- 4-pole audio headphone jack
- Microphone
- External speaker connection
Power
- 5 V DC jack
Debug
- JTAG 10-pin connector
- OpenSDA with DAPLink

For more information about the MIMXRT1024 SoC and MIMXRT1024-EVK board, see these references:

Supported Features¶

The mimxrt1024_evk board configuration supports the following hardware features:

Interface	Controller	Driver/Component
NVIC	on-chip	nested vector interrupt controller
SYSTICK	on-chip	systick
GPIO	on-chip	gpio
UART	on-chip	serial port-polling; serial port-interrupt

The default configuration can be found in the defconfig file: boards/arm/mimxrt1024_evk/mimxrt1024_evk_defconfig

Other hardware features are not currently supported by the port.

Connections and I/Os¶

The MIMXRT1024 SoC has five pairs of pinmux/gpio controllers.

Name	Function	Usage
GPIO_AD_B1_08	GPIO	LED
GPIO_AD_B0_06	LPUART1_TX	UART Console
GPIO_AD_B0_07	LPUART1_RX	UART Console
WAKEUP	GPIO	SW4

System Clock¶

The MIMXRT1024 SoC is configured to use the 24 MHz external oscillator on the board with the on-chip PLL to generate a 500 MHz core clock.

Serial Port¶

The MIMXRT1024 SoC has eight UARTs. One is configured for the console and the remaining are not used.

Programming and Debugging¶

Build and flash applications as usual (see Building an Application and Run an Application for more details).

Configuring a Debug Probe¶

A debug probe is used for both flashing and debugging the board. This board is configured by default to use the OpenSDA DAPLink Onboard Debug Probe, however the pyOCD Debug Host Tools do not yet support programming the external flashes on this board so you must reconfigure the board for one of the following debug probes instead.

J-Link External Debug Probe ¶

Install the J-Link Debug Host Tools and make sure they are in your search path.

Attach a J-Link 10-pin connector to J55. Check that jumpers J47 and J48 are off (they are on by default when boards ship from the factory) to ensure SWD signals are disconnected from the OpenSDA microcontroller.

Configuring a Console¶

Regardless of your choice in debug probe, we will use the OpenSDA microcontroller as a usb-to-serial adapter for the serial console. Check that jumpers J50 and J46 are on (they are on by default when boards ship from the factory) to connect UART signals to the OpenSDA microcontroller.

Connect a USB cable from your PC to J23.

Use the following settings with your serial terminal of choice (minicom, putty, etc.):

Speed: 115200
Data: 8 bits
Parity: None
Stop bits: 1

Flashing¶

Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b mimxrt1024_evk samples/hello_world
west flash

Open a serial terminal, reset the board (press the SW9 button), and you should see the following message in the terminal:

***** Booting Zephyr OS v2.4.0-rc1 *****
Hello World! mimxrt1024_evk

Debugging¶