ST STM32U083C_DK

Overview

The STM32U083C_DK board, featuring an ARM Cortex-M0+ based STM32U083MC MCU, provides an affordable and flexible way for users to try out new concepts and build prototypes by choosing from the various combinations of performance and power consumption features. Here are some highlights of the STM32U083C_DK board:

  • Ultra-low-power STM32U083MC microcontroller based on the Arm® Cortex®‑M0+ core, featuring 256 Kbytes of flash memory and 40 Kbytes of SRAM in an LQFP80 package.

  • Board connectors:

    • ST-LINK USB Type-C connector

    • User USB Device with USB Type-C connector

    • mikroBUS connectors

    • MIPI debug in connector (Arm® Cortex® 10‑pin 1.27 mm‑pitch debug connector over STDC14 footprint)

    • Extension connectors for full access to all STM32 I/Os

    • VBAT dedicated connector provides the capability to power the board on a battery

  • Flexible power-supply options:

    • ST-LINK USB VBUS, USB connector, or external sources

  • 4×24-segment LCD

  • Three user LEDs

  • Reset push-button

  • User joystick

  • Touchkey

  • Temperature sensor

Hardware

The STM32U083xC devices are an ultra-low-power microcontrollers family (STM32U0 Series) based on the high-performance Arm® Cortex®-M0+ 32-bit RISC core. They operate at a frequency of up to 56 MHz.

  • Includes ST state-of-the-art patented technology

  • Ultra-low-power with FlexPowerControl:

    • 1.71 V to 3.6 V power supply

    • -40 °C to +85/125 °C temperature range

    • 130 nA VBAT mode: supply for RTC, 9 x 32-bit backup registers

    • 16 nA Shutdown mode (6 wake-up pins)

    • 30 nA Standby mode (6 wake-up pins) without RTC

    • 160 nA Standby mode with RTC

    • 825 nA Stop 2 mode with RTC

    • 695 nA Stop 2 mode without RTC

    • 4 µA wake-up from Stop mode

    • 52 µA/MHz Run mode (LDO mode)

    • Brownout reset

  • Core:

    • 32-bit Arm® Cortex®-M0+ CPU, frequency up to 56 MHz

  • ART Accelerator:

    • 1-Kbyte instruction cache allowing 0-wait-state execution from flash memory

  • Benchmarks:

    • 1.13 DMIPS/MHz (Drystone 2.1)

    • 134 CoreMark® (2.4 CoreMark/MHz at 56 MHz)

    • 407 ULPMark™-CP

    • 143 ULPMark™-PP

    • 19.7 ULPMark™-CM

  • Memories:

    • 256-Kbyte single bank flash memory, proprietary code readout protection

    • 40-Kbyte SRAM with hardware parity check

  • General-purpose input/outputs:

    • Up to 69 fast I/Os, most of them 5 V‑tolerant

  • Clock management:

    • 4 to 48 MHz crystal oscillator

    • 32 kHz crystal oscillator for RTC (LSE)

    • Internal 16 MHz factory-trimmed RC (±1%)

    • Internal low-power 32 kHz RC (±5%)

    • Internal multispeed 100 kHz to 48 MHz oscillator, auto-trimmed by LSE (better than ±0.25 % accuracy)

    • Internal 48 MHz with clock recovery

    • PLL for system clock, USB, ADC

  • Security:

    • Customer code protection

    • Robust read out protection (RDP): 3 protection level states and password-based regression (128-bit PSWD)

    • Hardware protection feature (HDP)

    • Secure boot

    • AES: 128/256-bit key encryption hardware accelerator

    • True random number generation, candidate for NIST SP 800-90B certification

    • Candidate for Arm® PSA level 1 and SESIP level 3 certifications

    • 5 passive anti-tamper pins

    • 96-bit unique ID

  • Up to 10 timers, 2 watchdogs and RTC:

    • 1x 16-bit advanced motor-control, 1x 32-bit and 3x 16-bit general purpose, 2x 16-bit basic, 3x low-power 16-bit timers (available in Stop mode), 2x watchdogs, SysTick timer

    • RTC with hardware calendar, alarms and calibration

  • Up to 20 communication peripherals:

    • 1 USB 2.0 full-speed crystal-less solution with LPM and BCD

    • 7 USARTs/LPUARTs (SPI, ISO 7816, LIN, IrDA, modem)

    • 4 I2C interfaces supporting Fast-mode and Fast-mode Plus (up to 1 Mbit/s)

    • 3 SPIs, plus 4x USARTs in SPI mode

    • IRTIM (Infrared interface)

  • Rich analog peripherals (independent supply):

    • 1x 12-bit ADC (0.4 µs conversion time), up to 16-bit with hardware oversampling

    • 1x 12-bit DAC output channel, low-power sample and hold

    • 1x general-purpose operational amplifier with built-in PGA (variable gain up to 16)

    • 2x ultra-low-power comparators

  • LCD driver: - 8*48 or 4*52 segments, with step-up converter

  • General-purpose inputs/outputs: - Up to 69 fast I/Os, most of them 5 V-tolerant

  • ECOPACK2 compliant packages

More information about STM32U083MC can be found here:

Supported Features

The Zephyr stm32u083c_dk board configuration supports the following hardware features:

Interface

Controller

Driver/Component

CLOCK

on-chip

reset and clock control

GPIO

on-chip

gpio

NVIC

on-chip

nested vector interrupt controller

UART

on-chip

serial port-polling; serial port-interrupt

DAC

on-chip

DAC Controller

I2C

on-chip

i2c

Other hardware features are not yet supported on this Zephyr port.

The default configuration can be found in the defconfig file: boards/st/stm32u083c_dk/stm32u083c_dk_defconfig

Connections and IOs

STM32U083C_DK Board has 10 GPIO controllers. These controllers are responsible for pin muxing, input/output, pull-up, etc.

For more details please refer to STM32U083MC User Manual.

Default Zephyr Peripheral Mapping:

  • ADC1_IN8 : PA4

  • I2C1_SCL : PB8

  • I2C1_SDA : PB9

  • LPUART_1_TX : PG7

  • LPUART_1_RX : PG8

  • SPI1_NSS : PA4

  • SPI1_SCK : PA5

  • SPI1_MISO : PA6

  • SPI1_MOSI : PA7

  • SPI1_CS : PA15

  • UART_2_TX : PA2

  • UART_2_RX : PA3

System Clock

STM32U083C_DK System Clock could be driven by internal or external oscillator, as well as main PLL clock. By default System clock is driven by PLL clock at 48MHz, driven by 4MHz medium speed internal oscillator.

Serial Port

STM32U083C_DK board has 7 U(S)ARTs. The Zephyr console output is assigned to USART2. Default settings are 115200 8N1.

Programming and Debugging

STM32U083C_DK board includes an ST-LINK/V3 embedded debug tool interface. This probe allows to flash the board using various tools.

Flashing

The board is configured to be flashed using west STM32CubeProgrammer runner, so its installation is required.

Alternatively, JLink or pyOCD can also be used to flash the board using the --runner (or -r) option:

$ west flash --runner pyocd
$ west flash --runner jlink

For pyOCD, additional target information needs to be installed. This can be done by executing the following commands.

$ pyocd pack --update
$ pyocd pack --install stm32u0

Flashing an application to STM32U083C_DK

Connect the STM32U083C_DK to your host computer using the USB port. Then build and flash an application. Here is an example for the Hello World application.

Run a serial host program to connect with your Nucleo board:

$ minicom -D /dev/ttyACM0

Then build and flash the application.

# From the root of the zephyr repository
west build -b stm32u083c_dk samples/hello_world
west flash

You should see the following message on the console:

Hello World! stm32u083c_dk/stm32u083xx

Debugging

Default flasher for this board is openocd. It could be used in the usual way. Here is an example for the Blinky application.

# From the root of the zephyr repository
west build -b nucleo_u083rc samples/basic/blinky
west debug

Note: Check the build/tfm directory to ensure that the commands required by these scripts (readlink, etc.) are available on your system. Please also check STM32_Programmer_CLI (which is used for initialization) is available in the PATH.