ST Nucleo F410RB

Overview

The Nucleo F410RB board features an ARM Cortex-M4 based STM32F410RB MCU with a wide range of connectivity support and configurations. Here are some highlights of the Nucleo F410RB board:

  • STM32 microcontroller in QFP64 package

  • Two types of extension resources:

    • Arduino Uno V3 connectivity

    • ST morpho extension pin headers for full access to all STM32 I/Os

  • On-board ST-LINK/V2-1 debugger/programmer with SWD connector

  • Flexible board power supply:

    • USB VBUS or external source(3.3V, 5V, 7 - 12V)

    • Power management access point

  • Three LEDs: USB communication (LD1), user LED (LD2), power LED (LD3)

  • Two push-buttons: USER and RESET

Nucleo F410RB

More information about the board can be found at the Nucleo F410RB website.

Hardware

Nucleo F410RB provides the following hardware components:

  • STM32F410RBT6 in LQFP64 package

  • ARM® 32-bit Cortex®-M4 CPU with FPU

  • Adaptive real-time accelerator (ART Accelerator)

  • 100 MHz max CPU frequency

  • VDD from 1.7 V to 3.6 V

  • 128 KB Flash

  • 32 KB SRAM

  • General purpose timer (4)

  • Low-power timer (1)

  • Advanced-control timer (1)

  • Random number generator (TRNG for HW entropy)

  • SPI/I2S (3)

  • I2C (3)

  • USART (3)

  • GPIO (50) with external interrupt capability

  • 12-bit ADC with 16 channels

  • 12-bit DAC with 1 channel

  • RTC

More information about STM32F410RB can be found here:

Supported Features

The Zephyr nucleo_f410rb board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

UART

on-chip

serial port

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

PWM

on-chip

pwm

I2C

on-chip

i2c

I2S

on-chip

i2s

SPI

on-chip

spi

ADC

on-chip

ADC Controller

DAC

on-chip

DAC Controller

WATCHDOG

on-chip

window & independent

Other hardware features are not yet supported on this Zephyr port.

The default configuration can be found in boards/st/nucleo_f410rb/nucleo_f410rb_defconfig

Connections and IOs

Nucleo F410RB Board has 8 GPIO controllers. These controllers are responsible for pin muxing, input/output, pull-up, etc.

Available pins:

Nucleo F410RB Arduino connectors (top left) Nucleo F410RB Arduino connectors (top right) Nucleo F410RB Morpho connectors (top left) Nucleo F410RB Morpho connectors (top right)

For more details please refer to STM32 Nucleo-64 board User Manual.

Default Zephyr Peripheral Mapping:

  • UART_1_TX : PB6

  • UART_1_RX : PB7

  • UART_2_TX : PA2

  • UART_2_RX : PA3

  • USER_PB : PC13

  • LD2 : PA5

  • I2C1_SDA : PB9

  • I2C1_SCL : PB8

  • I2C2_SDA : PB3

  • I2C2_SCL : PB10

System Clock

Nucleo F410RB System Clock could be driven by an internal or external oscillator, as well as the main PLL clock. By default, the System clock is driven by the PLL clock at 84MHz, driven by an 8MHz high-speed external clock.

Serial Port

Nucleo F410RB board has 3 USARTs. The Zephyr console output is assigned to UART2. Default settings are 115200 8N1.

Programming and Debugging

Applications for the nucleo_f410rb board configuration can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Flashing

Nucleo F410RB board includes an ST-LINK/V2-1 embedded debug tool interface. This interface is supported by the openocd version included in the Zephyr SDK.

Flashing an application to Nucleo F410RB

Here is an example for the Hello World application.

Run a serial host program to connect with your Nucleo board.

$ minicom -b 115200 -D /dev/ttyACM0

Build and flash the application:

# From the root of the zephyr repository
west build -b nucleo_f410rb samples/hello_world
west flash

You should see the following message on the console:

$ Hello World! arm

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b nucleo_f410rb samples/hello_world
west debug