Bluetooth: Peripheral GATT Discovery Manager

The Peripheral GATT Discovery Manager sample demonstrates how to use the GATT Discovery Manager.

Requirements

The sample supports the following development kits:

Hardware platforms

PCA

Board name

Board target

nRF54L15 DK

PCA10156

nrf54l15dk

nrf54l15dk/nrf54l15/cpuapp

nRF54H20 DK

PCA10175

nrf54h20dk

nrf54h20dk/nrf54h20/cpuapp

nRF5340 DK

PCA10095

nrf5340dk

nrf5340dk/nrf5340/cpuapp/ns nrf5340dk/nrf5340/cpuapp

nRF52 DK

PCA10040

nrf52dk

nrf52dk/nrf52832

nRF52840 DK

PCA10056

nrf52840dk

nrf52840dk/nrf52840

When built for a board target with the */ns variant, the sample is configured to compile and run as a non-secure application with Cortex-M Security Extensions enabled. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

The sample also requires a device to connect to the peripheral, for example, a phone or a tablet with nRF Connect for Mobile or nRF Toolbox.

Overview

When connected to another device, the sample discovers the services of the connected device and outputs the service information.

User interface

Button 1:

During the pairing procedure, press this button to accept the pairing.

Button 2:

During the pairing procedure, press this button to reject the pairing.

Building and running

This sample can be found under samples/bluetooth/peripheral_gatt_dm in the nRF Connect SDK folder structure.

When built as firmware image for a board target with the */ns variant, the sample has Cortex-M Security Extensions (CMSE) enabled and separates the firmware between Non-Secure Processing Environment (NSPE) and Secure Processing Environment (SPE). Because of this, it automatically includes the Trusted Firmware-M (TF-M). To read more about CMSE, see Processing environments.

To build the sample, follow the instructions in Building an application for your preferred building environment. See also Programming an application for programming steps and Testing and optimization for general information about testing and debugging in the nRF Connect SDK.

Note

When building repository applications in the SDK repositories, building with sysbuild is enabled by default. If you work with out-of-tree freestanding applications, you need to manually pass the --sysbuild parameter to every build command or configure west to always use it.

Note

When using the nRF54H20 DK Engineering B (from v0.8.0 to 0.8.2), you must build samples and applications using the board revision 0.8.0 with the <board>@<revision> syntax. For example, nrf54h20dk@0.8.0/nrf54h20/cpuapp when building for the application core, or nrf54h20dk@0.8.0/nrf54h20/cpurad when building for the radio core.

Testing

After programming the sample to your dongle or development kit, test it by performing the following steps. This testing procedure assumes that you are using nRF Connect for Mobile.

  1. Connect the kit to the computer using a USB cable. The kit is assigned a COM port (Windows) or ttyACM device (Linux), which is visible in the Device Manager.

  2. Connect to the kit with a terminal emulator (for example, nRF Connect Serial Terminal). See Testing and optimization for the required settings and steps.

  3. Connect to the device from nRF Connect (the device is advertising as “Nordic Discovery Sample”). When connected, the sample starts discovering the services of the connected device.

  4. Observe that the services of the connected device are printed in the terminal emulator.

Dependencies

This sample uses the following nRF Connect SDK libraries:

In addition, it uses the following Zephyr libraries:

  • include/zephyr/types.h

  • lib/libc/minimal/include/errno.h

  • include/sys/printk.h

  • include/sys/byteorder.h

  • API:

    • include/bluetooth/bluetooth.h

    • include/bluetooth/hci.h

    • include/bluetooth/conn.h

    • include/bluetooth/uuid.h

    • include/bluetooth/gatt.h

The sample also uses the following secure firmware component: