Bluetooth: Central UART

The Central UART sample demonstrates how to use the Nordic UART Service (NUS) Client. It uses the NUS Client to send data back and forth between a UART connection and a Bluetooth® LE connection, emulating a serial port over Bluetooth LE.

Requirements

The sample supports the following development kits:

Hardware platforms

PCA

Board name

Board target

nRF54L15 PDK

PCA10156

nrf54l15pdk

nrf54l15pdk/nrf54l15/cpuapp

nRF54L15 DK

PCA10156

nrf54l15dk

nrf54l15dk/nrf54l15/cpuapp

nRF54H20 DK

PCA10175

nrf54h20dk

nrf54h20dk/nrf54h20/cpuapp

nRF5340 DK

PCA10095

nrf5340dk

nrf5340dk/nrf5340/cpuapp/ns nrf5340dk/nrf5340/cpuapp

nRF52 DK

PCA10040

nrf52dk

nrf52dk/nrf52832

nRF52840 DK

PCA10056

nrf52840dk

nrf52840dk/nrf52840

nRF21540 DK

PCA10112

nrf21540dk

nrf21540dk/nrf52840

When built for a board target with the */ns variant, the sample is configured to compile and run as a non-secure application with Cortex-M Security Extensions enabled. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

The sample also requires another development kit running a compatible application (see Bluetooth: Peripheral UART).

Overview

When connected, the sample forwards any data received on the RX pin of the UART 1 peripheral to the Bluetooth LE unit. On Nordic Semiconductor’s development kits, the UART 1 peripheral is typically gated through the SEGGER chip to a USB CDC virtual serial port.

Any data sent from the Bluetooth LE unit is sent out of the UART 1 peripheral’s TX pin.

Debugging

In this sample, a UART console is used to send and read data over the NUS Client. Debug messages are not displayed in the UART console, but are printed by the RTT logger instead.

If you want to view the debug messages, follow the procedure in Testing and optimization.

FEM support

You can add support for the nRF21540 front-end module to this sample by using one of the following options, depending on your hardware:

  • Build the sample for one board that contains the nRF21540 FEM, such as nrf21540dk/nrf52840.

  • Manually create a devicetree overlay file that describes how FEM is connected to the nRF5 SoC in your device. See Set devicetree overlays for different ways of adding the overlay file.

  • Provide nRF21540 FEM capabilities by using a shield, for example the Developing with the nRF21540 EK shield that is available in the nRF Connect SDK. In this case, build the project for a board connected to the shield you are using with an appropriate variable included in the build command, for example SHIELD=nrf21540ek. This variable instructs the build system to append the appropriate devicetree overlay file.

    To build the sample in the nRF Connect for VS Code IDE for an nRF52840 DK with the nRF21540 EK attached, add the shield variable in the build configuration’s Extra CMake arguments and rebuild the build configuration. For example: -DSHIELD=nrf21540ek.

    See nRF Connect for VS Code extension pack documentation for more information.

    See Programming nRF21540 EK for information about how to program when you are using a board with a network core, for example nRF5340 DK.

Each of these options adds the description of the nRF21540 FEM to the devicetree. See Developing with Front-End Modules for more information about FEM in the nRF Connect SDK.

To add support for other front-end modules, add the respective devicetree file entries to the board devicetree file or the devicetree overlay file.

Building and running

This sample can be found under samples/bluetooth/central_uart in the nRF Connect SDK folder structure.

When built as firmware image for a board target with the */ns variant, the sample has Cortex-M Security Extensions (CMSE) enabled and separates the firmware between Non-Secure Processing Environment (NSPE) and Secure Processing Environment (SPE). Because of this, it automatically includes the Trusted Firmware-M (TF-M). To read more about CMSE, see Processing environments.

To build the sample, follow the instructions in Building an application for your preferred building environment. See also Programming an application for programming steps and Testing and optimization for general information about testing and debugging in the nRF Connect SDK.

Note

When building repository applications in the SDK repositories, building with sysbuild is enabled by default. If you work with out-of-tree freestanding applications, you need to manually pass the --sysbuild parameter to every build command or configure west to always use it.

Note

Programming the nRF54H20 SoC can sometimes fail due to conflicts in the resource configuration. This can happen if, for example, an application programmed to the nRF54H20 SoC configured the UICRs for one or more cores in a way that is incompatible with the configuration required by the application you are trying to program on the SoC.

To fix this error and erase the UICR for the application core, run the following command:

nrfutil device recover --core Application

If your sample also uses the radio core, you must also erase the UICRs for the radio core. To erase the UICR for the radio core, run the following command:

nrfutil device recover --core Network

For more information on the command, run:

nrfutil device recover --help

You can then run west flash to program your application.

Testing

After programming the sample to your development kit, complete the following steps to test it:

  1. Connect the kit to the computer using a USB cable. The kit is assigned a COM port (Windows) or ttyACM device (Linux), which is visible in the Device Manager.

  2. Connect to the kit that runs this sample with a terminal emulator (for example, nRF Connect Serial Terminal). See Testing and optimization for the required settings and steps.

  3. Optionally, connect the RTT console to display debug messages. See Debugging.

  4. Reset the kit.

  5. Observe that the text “Starting Bluetooth Central UART example” is printed on the COM listener running on the computer and the device starts scanning for Peripherals with NUS.

  6. Program the Bluetooth: Peripheral UART sample to the second development kit. See the documentation for that sample for detailed instructions.

  7. Observe that the kits connect.

    When service discovery is completed, the event logs are printed on the Central’s terminal. Now you can send data between the two kits.

  8. To send data, type some characters in the terminal of one of the kits and press Enter. Observe that the data is displayed on the UART on the other kit.

  9. Disconnect the devices by, for example, pressing the Reset button on the Central. Observe that the kits automatically reconnect and that it is again possible to send data between the two kits.

Dependencies

This sample uses the following nRF Connect SDK libraries:

In addition, it uses the following Zephyr libraries:

  • include/zephyr/types.h

  • boards/arm/nrf*/board.h

  • Kernel Services:

    • include/kernel.h

  • Peripherals:

    • include/uart.h

  • API:

    • include/bluetooth/bluetooth.h

    • include/bluetooth/gatt.h

    • include/bluetooth/hci.h

    • include/bluetooth/uuid.h

The sample also uses the following secure firmware component: