Pin Controller Interface

Pin Controller Interface. More...

Modules
	Dynamic Pin Control

Data Structures
struct	pinctrl_state
	Pin control state configuration. More...
struct	pinctrl_dev_config
	Pin controller configuration for a given device. More...

Macros
#define	PINCTRL_REG_NONE   0U
	Utility macro to indicate no register is used.
#define	PINCTRL_DT_DEV_CONFIG_DECLARE(node_id)
	Declare pin control configuration for a given node identifier.
#define	PINCTRL_DT_DEFINE(node_id)
	Define all pin control information for the given node identifier.
#define	PINCTRL_DT_INST_DEFINE(inst)   PINCTRL_DT_DEFINE(DT_DRV_INST(inst))
	Define all pin control information for the given compatible index.
#define	PINCTRL_DT_DEV_CONFIG_GET(node_id)   &Z_PINCTRL_DEV_CONFIG_NAME(node_id)
	Obtain a reference to the pin control configuration given a node identifier.
#define	PINCTRL_DT_INST_DEV_CONFIG_GET(inst)    PINCTRL_DT_DEV_CONFIG_GET(DT_DRV_INST(inst))
	Obtain a reference to the pin control configuration given current compatible instance number.

Functions
int	pinctrl_lookup_state (const struct pinctrl_dev_config *config, uint8_t id, const struct pinctrl_state **state)
	Find the state configuration for the given state id.
int	pinctrl_configure_pins (const pinctrl_soc_pin_t *pins, uint8_t pin_cnt, uintptr_t reg)
	Configure a set of pins.
static int	pinctrl_apply_state_direct (const struct pinctrl_dev_config *config, const struct pinctrl_state *state)
	Apply a state directly from the provided state configuration.
static int	pinctrl_apply_state (const struct pinctrl_dev_config *config, uint8_t id)
	Apply a state from the given device configuration.

Pin control states
#define	PINCTRL_STATE_DEFAULT   0U
	Default state (state used when the device is in operational state).
#define	PINCTRL_STATE_SLEEP   1U
	Sleep state (state used when the device is in low power mode).
#define	PINCTRL_STATE_PRIV_START   2U
	This and higher values refer to custom private states.

Detailed Description

Pin Controller Interface.

Since

3.0

Version

0.1.0

Macro Definition Documentation

PINCTRL_DT_DEFINE

#define PINCTRL_DT_DEFINE

(

node_id

)

#include <zephyr/drivers/pinctrl.h>

Value:

        LISTIFY(DT_NUM_PINCTRL_STATES(node_id),                                \
                     Z_PINCTRL_STATE_PINS_DEFINE, (;), node_id);               \
        Z_PINCTRL_STATES_DEFINE(node_id)                                       \
        Z_PINCTRL_DEV_CONFIG_STATIC Z_PINCTRL_DEV_CONFIG_CONST                 \
        struct pinctrl_dev_config Z_PINCTRL_DEV_CONFIG_NAME(node_id) =         \
        Z_PINCTRL_DEV_CONFIG_INIT(node_id)

Define all pin control information for the given node identifier.

This helper macro should be called together with device definition. It defines and initializes the pin control configuration for the device represented by node_id. Each pin control state (pinctrl-0, ..., pinctrl-N) is also defined and initialized. Note that states marked to be skipped will not be defined (refer to Z_PINCTRL_SKIP_STATE for more details).

Parameters

node_id

Node identifier.

PINCTRL_DT_DEV_CONFIG_DECLARE

#define PINCTRL_DT_DEV_CONFIG_DECLARE

(

node_id

)

#include <zephyr/drivers/pinctrl.h>

Value:

        extern Z_PINCTRL_DEV_CONFIG_CONST struct pinctrl_dev_config            \
        Z_PINCTRL_DEV_CONFIG_NAME(node_id)

Declare pin control configuration for a given node identifier.

This macro should be used by tests or applications using runtime pin control to declare the pin control configuration for a device. PINCTRL_DT_DEV_CONFIG_GET can later be used to obtain a reference to such configuration.

Only available if CONFIG_PINCTRL_NON_STATIC is selected.

Parameters

node_id

Node identifier.

PINCTRL_DT_DEV_CONFIG_GET

#define PINCTRL_DT_DEV_CONFIG_GET

(

node_id

)

&Z_PINCTRL_DEV_CONFIG_NAME(node_id)

#include <zephyr/drivers/pinctrl.h>

Obtain a reference to the pin control configuration given a node identifier.

Parameters

node_id

Node identifier.

PINCTRL_DT_INST_DEFINE

#define PINCTRL_DT_INST_DEFINE

(

inst

)

PINCTRL_DT_DEFINE(DT_DRV_INST(inst))

#include <zephyr/drivers/pinctrl.h>

Define all pin control information for the given compatible index.

Parameters

inst	Instance number.

See also

PINCTRL_DT_DEFINE

PINCTRL_DT_INST_DEV_CONFIG_GET

#define PINCTRL_DT_INST_DEV_CONFIG_GET

(

inst

)

PINCTRL_DT_DEV_CONFIG_GET(DT_DRV_INST(inst))

#include <zephyr/drivers/pinctrl.h>

Obtain a reference to the pin control configuration given current compatible instance number.

Parameters

inst	Instance number.

See also

PINCTRL_DT_DEV_CONFIG_GET

PINCTRL_REG_NONE

#define PINCTRL_REG_NONE   0U

#include <zephyr/drivers/pinctrl.h>

Utility macro to indicate no register is used.

PINCTRL_STATE_DEFAULT

#define PINCTRL_STATE_DEFAULT   0U

#include <zephyr/drivers/pinctrl.h>

Default state (state used when the device is in operational state).

PINCTRL_STATE_PRIV_START

#define PINCTRL_STATE_PRIV_START   2U

#include <zephyr/drivers/pinctrl.h>

This and higher values refer to custom private states.

PINCTRL_STATE_SLEEP

#define PINCTRL_STATE_SLEEP   1U

#include <zephyr/drivers/pinctrl.h>

Sleep state (state used when the device is in low power mode).

Function Documentation

pinctrl_apply_state()

static int pinctrl_apply_state ( const struct pinctrl_dev_config *  config, uint8_t  id  )

inlinestatic

#include <zephyr/drivers/pinctrl.h>

Apply a state from the given device configuration.

Parameters

config	Pin control configuration.
id	Id of the state to be applied (see PINCTRL_STATES).

Return values

0	If succeeded.
-ENOENT	If given state id does not exist.
-errno	Negative errno for other failures.

pinctrl_apply_state_direct()

static int pinctrl_apply_state_direct ( const struct pinctrl_dev_config *  config, const struct pinctrl_state *  state  )

inlinestatic

#include <zephyr/drivers/pinctrl.h>

Apply a state directly from the provided state configuration.

Parameters

config	Pin control configuration.
state	State.

Return values

0	If succeeded
-errno	Negative errno for other failures.

pinctrl_configure_pins()

int pinctrl_configure_pins	(	const pinctrl_soc_pin_t *	pins,
		uint8_t	pin_cnt,
		uintptr_t	reg
	)

#include <zephyr/drivers/pinctrl.h>

Configure a set of pins.

This function will configure the necessary hardware blocks to make the configuration immediately effective.

Warning

This function must never be used to configure pins used by an instantiated device driver.

Parameters

pins	List of pins to be configured.
pin_cnt	Number of pins.
reg	Device register (optional, use PINCTRL_REG_NONE if not used).

Return values

0	If succeeded
-errno	Negative errno for other failures.

pinctrl_lookup_state()

int pinctrl_lookup_state	(	const struct pinctrl_dev_config *	config,
		uint8_t	id,
		const struct pinctrl_state **	state
	)

#include <zephyr/drivers/pinctrl.h>

Find the state configuration for the given state id.

Parameters

config	Pin controller configuration.
id	Pin controller state id (see PINCTRL_STATES).
state	Found state.

Return values

0	If state has been found.
-ENOENT	If the state has not been found.