nRF9160: TLS cipher suites

The Transport Layer Security (TLS) cipher suites sample demonstrates a minimal implementation of a client application that attempts to connect to a host by trying different TLS cipher suites. This sample shows the cipher suites and lists them as supported or not supported by the host, and provides a summary of the support.

Requirements

The sample supports the following development kit:

Hardware platforms

PCA

Board name

Build target

nRF9160 DK

PCA10090

nrf9160dk_nrf9160

nrf9160dk_nrf9160_ns

When built for an _ns build target, the sample is configured to compile and run as a non-secure application with Cortex-M Security Extensions enabled. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

Overview

The sample first initializes the Modem library and AT communications. Next, it provisions a root CA certificate to the modem using the Modem key management library. Provisioning must be done before connecting to the LTE network because the certificates can only be provisioned when the device is not connected.

The sample then iterates through a list of TLS cipher suites, attempting connection to the host with each one of them. The sample connects successfully to the host (www.example.com) with the cipher suites that are supported by the host, while unsupported cipher suites cause a connection failure, setting errno to 95.

Finally, the sample provides a summary of the cipher suites that are supported and not supported by the host, example.com.

Obtaining a certificate

The sample connects to www.example.com, which requires an X.509 certificate. This certificate is provided in the samples/nrf9160/https_client/cert folder.

To connect to other servers, you might need to provision a different certificate. See Certificates for more information.

Configuration

See Configuring your application for information about how to permanently or temporarily change the configuration.

Configuration options

Check and configure the following Kconfig options:

CONFIG_EXTENDED_CIPHERSUITE_LIST

The sample configuration extends the cipher suite list with extra cipher suites that are only supported by modem firmware v1.3.x, where x is greater than or equal to 1 and modem firmware v1.2.x, where x is greater than or equal to 7.

Building and running

This sample can be found under samples/nrf9160/ciphersuites in the nRF Connect SDK folder structure.

When built as firmware image for the _ns build target, the sample has Cortex-M Security Extensions (CMSE) enabled and separates the firmware between Non-Secure Processing Environment (NSPE) and Secure Processing Environment (SPE). Because of this, it automatically includes the Trusted Firmware-M (TF-M). To read more about CMSE, see Processing environments.

To build the sample with Visual Studio Code, follow the steps listed on the How to build an application page in the nRF Connect for VS Code extension documentation. See Building and programming an application for other building and programming scenarios and Testing and debugging an application for general information about testing and debugging in the nRF Connect SDK.

Testing

After programming the sample to your development kit, complete the following steps to test it:

  1. Connect the kit to the computer using a USB cable. The kit is assigned a COM port (Windows) or ttyACM device (Linux), which is visible in the Device Manager.

  2. Connect to the kit with a terminal emulator (for example, PuTTY). See How to connect with PuTTY for the required settings.

  3. Observe that the sample starts, provisions certificates, and connects to the LTE network.

  4. Observe that the sample iterates through a list of cipher suites, attempting a connection to example.com with each one of them, showing either a successful or an unsuccessful connection.

Sample output

The sample shows the following output:

TLS ciphersuites sample started
certificate match
waiting for network.. OK
trying all ciphersuites to find which ones are supported...
trying ciphersuite: TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA384
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA256
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA
connecting to example.com... Connected.
trying ciphersuite: TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA256
connecting to example.com... Connected.
trying ciphersuite: TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
connecting to example.com... Connected.
trying ciphersuite: TLS_PSK_WITH_AES_256_CBC_SHA
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_PSK_WITH_AES_128_CBC_SHA256
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_PSK_WITH_AES_128_CBC_SHA
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_PSK_WITH_AES_128_CCM_8
connecting to example.com... connect() failed, err: 95, Operation not supported on socket
trying ciphersuite: TLS_EMPTY_RENEGOTIATIONINFO_SCSV
connecting to example.com... connect() failed, err: 95, Operation not supported on socket

Ciphersuite support summary for host `example.com`:
TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA384: No
TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA: No
TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA256: No
TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA: No
TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA: Yes
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA256: Yes
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA: Yes
TLS_PSK_WITH_AES_256_CBC_SHA: No
TLS_PSK_WITH_AES_128_CBC_SHA256: No
TLS_PSK_WITH_AES_128_CBC_SHA: No
TLS_PSK_WITH_AES_128_CCM_8: No
TLS_EMPTY_RENEGOTIATIONINFO_SCSV: No

finished.

Dependencies

This sample uses the following nRF Connect SDK libraries:

It uses the following sdk-nrfxlib library:

In addition, it uses the following secure firmware component: