Crypto: PSA TLS

The PSA TLS sample shows how to perform a TLS handshake and send encrypted messages in both a secure and a non-secure domain with Trusted Firmware-M.

Note

  • Datagram Transport Layer Security (DTLS) and Pre-shared key (PSK) are currently not supported.

Overview

The sample can act as either a network server or a network client. By default, the sample is configured to act as a server.

You can configure the following options to make the sample act as either a server or a client:

  • CONFIG_PSA_TLS_SAMPLE_TYPE_SERVER

    Set to y to make the sample act as a server. When acting as a server, the sample waits for a connection from the client on port 4243. After the TCP connection is established, the sample automatically initiates the TLS handshake by waiting for the ClientHello message from the client.

  • CONFIG_PSA_TLS_SAMPLE_TYPE_CLIENT

    Set to y to make the sample act as a client. When acting as a client, the sample tries to connect to the server on port 4243. After the TCP connection is established, the sample automatically initiates the TLS handshake by sending the ClientHello message.

After a successful TLS handshake, the client and server echo any message received over the secured connection.

Certificates

The sample supports certificates signed with either ECDSA or RSA. By default, the sample is configured to use ECDSA certificates. You can configure the following option to y to make the sample use RSA certificates:

  • CONFIG_PSA_TLS_CERTIFICATE_TYPE_RSA

Certificates when running in a non-secure domain

When the sample is compiled for a non-secure domain, it stores its TLS certificates and keys in the TF-M Protected Storage. During the sample initialization, the certificates and keys are fetched from TF-M Protected Storage and kept in non-secure RAM for use during every subsequent TLS handshake.

Note

Currently, non-secure applications only support ECDSA certificates. This is automatically enforced in the configuration files for non-secure builds.

Supported cipher suites

The sample supports most TLS v1.2 cipher suites, except for the following combinations:

  • RSA is not supported in non-secure applications.

  • AES256 is not supported in non-secure applications running on the nRF9160.

TAP adapter

The sample uses the Ethernet over RTT driver library in nRF Connect SDK to transfer Ethernet frames to the connected PC. The PC must parse the incoming RTT data and dispatch these packets to a running TAP network device. This functionality is called TAP adapter.

In Linux

The TAP adapter functionality for Linux is included in the Ethernet over RTT for Linux executable, named eth_rtt_link, located in the samples/crypto/psa_tls folder. You must pass the development kit’s Segger-ID and the TAP IPv4 as parameters when calling the executable. See the examples in the Testing section below.

When using an nRF5340 development kit, if eth_rtt_link is not able to start the RTT connection, pass the _SEGGER_RTT RAM block address as a parameter using --rttcbaddr, as shown in the following example:

sudo ./eth_rtt_link --snr 960010000 --ipv4 192.0.2.2 --rttcbaddr 0x20002000

You can find the _SEGGER_RTT RAM address in the .map file.

In Windows

There is currently no direct support for TAP adapters in Windows. However, you can still follow the steps given in the Testing section using a Linux distribution running inside a virtual machine.

Openssl

You can use the openssl command-line interface to perform the peer network operations when testing this sample.

It can act as either client or server with simple commands in a terminal. For more information, see the Testing section below.

Requirements

The sample supports the following development kits:

Hardware platforms

PCA

Board name

Build target

nRF5340 DK

PCA10095

nrf5340dk_nrf5340

nrf5340dk_nrf5340_cpuapp_ns

nRF9160 DK

PCA10090

nrf9160dk_nrf9160

nrf9160dk_nrf9160_ns

The sample requires a TAP adapter to perform the TLS handshake. This functionality is currently only supported in Linux.

Building and running

This sample can be found under samples/crypto/psa_tls in the nRF Connect SDK folder structure.

See Configuring your application and Building and programming an application for information about how to configure and how to build and program the application.

Testing

After programming the sample to your development kit, test it by performing the following steps:

  1. Start a terminal emulator like PuTTY and connect to the used COM port with the following UART settings:

    • Baud rate: 115.200

    • 8 data bits

    • 1 stop bit

    • No parity

    • HW flow control: None

  2. Observe the logs from the application using the terminal emulator.

  3. Start the eth_rtt_link executable as superuser with your development kit’s segger-id and the following ipv4 address as parameters:

    sudo ./eth_rtt_link --snr 960010000 --ipv4 192.0.2.2

  4. Use openssl to perform the client connection and handshake operation.

    openssl s_client -connect 192.0.2.1:4243 -cipher ECDHE-ECDSA-AES128-SHA256 -CAfile certs/ecdsa/root_cert.pem

    Note

    If the sample has been built with an RSA certificate, use this openssl command:

    openssl s_client -connect 192.0.2.1:4243 -cipher AES128-SHA256 -CAfile certs/rsa/root_cert.pem

    For visualizing a list of the available cipher suites for openssl, use the following command:

    openssl ciphers

  5. Type Nordic Semiconductor into the openssl connection session to send Nordic Semiconductor as an encrypted message to the server.

  6. Check that the TLS sample returns Nordic Semiconductor in the openssl session.

  7. Check in the terminal emulator that 21 bytes were successfully received and returned.

Dependencies

This sample uses the following Zephyr libraries:

  • Logging:

    • include/logging/log.h

  • BSD Sockets:

    • net/socket.h

  • net/net_core.h

  • net/tls_credentials.h

This sample also uses the following TF-M libraries:

  • tfm_ns_interface.h

  • psa/storage_common.h

  • psa/protected_storage.h