-
CONFIG_GPIO_SAM
¶
Atmel SAM GPIO (PORT) driver
Type: bool
Help¶
Enable support for the Atmel SAM ‘PORT’ GPIO controllers.
Direct dependencies¶
(GPIO
&& BOARD_ARDUINO_DUE
) || (GPIO
&& SOC_SERIES_SAM4E
) || (GPIO
&& SOC_SERIES_SAM4S
) || (GPIO
&& SOC_SERIES_SAME70
) || (GPIO
&& SOC_SERIES_SAMV71
) || (SOC_FAMILY_SAM
&& !SOC_SERIES_SAM4L
&& GPIO
)
(Includes any dependencies from ifs and menus.)
Defaults¶
y
y
y
y
y
y
Kconfig definitions¶
At <Zephyr>/boards/arm/arduino_due/Kconfig.defconfig:11
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:18
Menu path: (Top)
config GPIO_SAM bool default y depends onGPIO
&&BOARD_ARDUINO_DUE
At <Zephyr>/soc/arm/atmel_sam/sam4e/Kconfig.defconfig.series:29
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:19
→ <BuildDir>/Kconfig/Kconfig.soc.defconfig:1
→ <Zephyr>/soc/arm/atmel_sam/Kconfig.defconfig:6
Menu path: (Top)
config GPIO_SAM bool default y depends onGPIO
&&SOC_SERIES_SAM4E
At <Zephyr>/soc/arm/atmel_sam/sam4s/Kconfig.defconfig.series:34
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:19
→ <BuildDir>/Kconfig/Kconfig.soc.defconfig:1
→ <Zephyr>/soc/arm/atmel_sam/Kconfig.defconfig:6
Menu path: (Top)
config GPIO_SAM bool default y depends onGPIO
&&SOC_SERIES_SAM4S
At <Zephyr>/soc/arm/atmel_sam/same70/Kconfig.defconfig.series:51
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:19
→ <BuildDir>/Kconfig/Kconfig.soc.defconfig:1
→ <Zephyr>/soc/arm/atmel_sam/Kconfig.defconfig:6
Menu path: (Top)
config GPIO_SAM bool default y depends onGPIO
&&SOC_SERIES_SAME70
At <Zephyr>/soc/arm/atmel_sam/samv71/Kconfig.defconfig.series:52
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:19
→ <BuildDir>/Kconfig/Kconfig.soc.defconfig:1
→ <Zephyr>/soc/arm/atmel_sam/Kconfig.defconfig:6
Menu path: (Top)
config GPIO_SAM bool default y depends onGPIO
&&SOC_SERIES_SAMV71
At <Zephyr>/drivers/gpio/Kconfig.sam:7
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:32
→ <Zephyr>/drivers/Kconfig:34
→ <Zephyr>/drivers/gpio/Kconfig:56
Menu path: (Top) → Device Drivers → GPIO Drivers
config GPIO_SAM bool "Atmel SAM GPIO (PORT) driver" default y depends onSOC_FAMILY_SAM
&& !SOC_SERIES_SAM4L
&&GPIO
help Enable support for the Atmel SAM 'PORT' GPIO controllers.
(The ‘depends on’ condition includes propagated dependencies from ifs and menus.)