NXP MIMXRT1160-EVK

Overview

The dual core i.MX RT1160 runs on the Cortex-M7 core at 600 MHz and on the Cortex-M4 at 240 MHz. The i.MX RT1160 MCU offers support over a wide temperature range and is qualified for consumer, industrial and automotive markets.

MIMXRT1160-EVK

Hardware

  • MIMXRT1166DVM6A MCU

    • 600MHz Cortex-M7 & 240Mhz Cortex-M4

    • 2MB SRAM with 512KB of TCM for Cortex-M7 and 256KB of TCM for Cortex-M4

  • Memory

    • 512 Mbit SDRAM

    • 128 Mbit QSPI Flash

    • 512 Mbit Octal Flash

    • TF socket for SD card

  • Display

    • MIPI LCD connector

  • Ethernet

    • 10/100 Mbit/s Ethernet PHY

    • 10/100/1000 Mbit/s Ethernet PHY

  • USB

    • USB 2.0 OTG connector

    • USB 2.0 host connector

  • Audio

    • 3.5 mm audio stereo headphone jack

    • Board-mounted microphone

    • Left and right speaker out connectors

  • Power

    • 5 V DC jack

  • Debug

    • JTAG 20-pin connector

    • OpenSDA with DAPLink

  • Sensor

    • MIPI camera sensor connector

  • Expansion port

    • Arduino interface

  • CAN bus connector

For more information about the MIMXRT1160 SoC and MIMXRT1160-EVK board, see these references:

External Memory

This platform has the following external memories:

Device

Controller

Status

W9825G6KH

SEMC

Enabled via device configuration data block, which sets up SEMC at boot time

IS25WP128

FLEXSPI

Enabled via flash configurationn block, which sets up FLEXSPI at boot time.

Supported Features

The mimxrt1160_evk board configuration supports the hardware features listed below. For additional features not yet supported, please also refer to the NXP MIMXRT1170-EVK/EVKB , which is the superset board in NXP’s i.MX RT11xx family. NXP prioritizes enabling the superset board with NXP’s Full Platform Support for Zephyr. Therefore, the mimxrt1170_evk board may have additional features already supported, which can also be re-used on this mimxrt1160_evk board:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

SYSTICK

on-chip

systick

GPIO

on-chip

gpio

COUNTER

on-chip

counter

UART

on-chip

serial port-polling; serial port-interrupt

SPI

on-chip

spi

I2C

on-chip

i2c

ADC

on-chip

adc

CAN

on-chip

flexcan

WATCHDOG

on-chip

watchdog

PWM

on-chip

pwm

DMA

on-chip

dma

GPT

on-chip

gpt

USB

on-chip

USB Device

HWINFO

on-chip

Unique device serial number

CAAM RNG

on-chip

entropy

FLEXSPI

on-chip

flash programming

PIT

on-chip

pit

The default configuration can be found in the defconfig file: boards/nxp/mimxrt1160_evk/mimxrt1160_evk_mimxrt1166_cm7_defconfig

Other hardware features are not currently supported by the port.

Connections and I/Os

The MIMXRT1160 SoC has six pairs of pinmux/gpio controllers.

Name

Function

Usage

WAKEUP

GPIO

SW7

GPIO_AD_04

GPIO

LED

GPIO_AD_24

LPUART1_TX

UART Console

GPIO_AD_25

LPUART1_RX

UART Console

GPIO_LPSR_00

CAN3_TX

flexcan

GPIO_LPSR_01

CAN3_RX

flexcan

GPIO_AD_29

SPI1_CS0

spi

GPIO_AD_28

SPI1_CLK

spi

GPIO_AD_30

SPI1_SDO

spi

GPIO_AD_31

SPI1_SDI

spi

GPIO_AD_08

LPI2C1_SCL

i2c

GPIO_AD_09

LPI2C1_SDA

i2c

GPIO_LPSR_05

LPI2C5_SCL

i2c

GPIO_LPSR_04

LPI2C5_SDA

i2c

GPIO_AD_04

FLEXPWM1_PWM2

pwm

Dual Core samples

Core

Boot Address

Comment

Cortex M7

0x30000000[630K]

primary core

Cortex M4

0x20020000[96k]

boots from OCRAM

Memory

Address[Size]

Comment

flexspi1

0x30000000[16M]

Cortex M7 flash

sdram0

0x80030000[64M]

Cortex M7 ram

ocram

0x20020000[512K]

Cortex M4 “flash”

sram1

0x20000000[128K]

Cortex M4 ram

ocram2

0x200C0000[512K]

Mailbox/shared memory

Only the first 16K of ocram2 has the correct MPU region attributes set to be used as shared memory

System Clock

The MIMXRT1160 SoC is configured to use SysTick as the system clock source, running at 600MHz. When targeting the M4 core, SysTick will also be used, running at 240MHz

When power management is enabled, the 32 KHz low frequency oscillator on the board will be used as a source for the GPT timer to generate a system clock. This clock enables lower power states, at the cost of reduced resolution

Serial Port

The MIMXRT1160 SoC has 12 UARTs. One is configured for the console and the remaining are not used.

Programming and Debugging

Build and flash applications as usual (see Building an Application and Run an Application for more details).

Building a Dual-Core Image

Dual core samples load the M4 core image from flash into the shared ocram region. The M7 core then sets the M4 boot address to this region. The only sample currently enabled for dual core builds is the openamp sample. To flash a dual core sample, the M4 image must be flashed first, so that it is written to flash. Then, the M7 image must be flashed. The openamp sysbuild sample will do this automatically by setting the image order.

The secondary core can be debugged normally in single core builds (where the target is mimxrt1160_evk/mimxrt1166/cm4). For dual core builds, the secondary core should be placed into a loop, then a debugger can be attached (see AN13264, section 4.2.3 for more information)

Configuring a Debug Probe

A debug probe is used for both flashing and debugging the board. This board is configured by default to use the OpenSDA DAPLink Onboard Debug Probe, however the pyOCD Debug Host Tools do not yet support programming the external flashes on this board so you must reconfigure the board for one of the following debug probes instead.

Using LinkServer

Install the LinkServer Debug Host Tools and make sure they are in your search path. LinkServer works with the CMSIS-DAP firmware include in LinkServer install. Please follow the LPCScrypt\docs\Debug_Probe_Firmware_Programming.pdf for more details.

Linkserver is the default runner. You may also se the -r linkserver option with West to use the LinkServer runner.

Configuring a Console

Regardless of your choice in debug probe, we will use the OpenSDA microcontroller as a usb-to-serial adapter for the serial console. Check that jumpers J5 and J8 are on (they are on by default when boards ship from the factory) to connect UART signals to the OpenSDA microcontroller.

Connect a USB cable from your PC to J11.

Use the following settings with your serial terminal of choice (minicom, putty, etc.):

  • Speed: 115200

  • Data: 8 bits

  • Parity: None

  • Stop bits: 1

Flashing

Here is an example for the Hello World application.

Before power on the board, make sure SW1 is set to 0001b

# From the root of the zephyr repository
west build -b mimxrt1160_evk/mimxrt1166/cm7 samples/hello_world
west flash

Power off the board, and change SW1 to 0010b. Then power on the board and open a serial terminal, reset the board (press the SW4 button), and you should see the following message in the terminal:

***** Booting Zephyr OS v2.6.0-xxxx-xxxxxxxxxxxxx *****
Hello World! mimxrt1160_evk

Debugging

Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b mimxrt1160_evk/mimxrt1166/cm7 samples/hello_world
west debug

Open a serial terminal, step through the application in your debugger, and you should see the following message in the terminal:

***** Booting Zephyr OS v2.4.0-xxxx-xxxxxxxxxxxxx *****
Hello World! mimxrt1160_evk