Cellular: NIDD

The NIDD sample demonstrates how to use Non-IP Data Delivery (NIDD) on an nRF91 Series device.

Requirements

The sample supports the following development kits:

Hardware platforms

PCA

Board name

Board target

Thingy:91

PCA20035

thingy91

thingy91/nrf9160/ns

nRF9161 DK

PCA10153

nrf9161dk

nrf9161dk/nrf9161/ns

nRF9160 DK

PCA10090

nrf9160dk

nrf9160dk/nrf9160/ns

nRF9151 DK

PCA10171

nrf9151dk

nrf9151dk/nrf9151/ns

When built for a board target with the */ns variant, the sample is configured to compile and run as a non-secure application with Cortex-M Security Extensions enabled. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

Overview

The NIDD sample creates a non-IP PDN using the configured APN and uses socket operations to send and receive data. You can allocate a new PDN context to allow dual stack communication (IP and non-IP).

Note

This sample requires a SIM subscription with non-IP service enabled, and LTE network configured to route the non-IP traffic to a server that is able to respond. Before using the sample, check with your operator if non-IP service is supported.

Configuration

See Configuring and building for information about how to permanently or temporarily change the configuration.

Configuration options

Check and configure the following configuration options for the sample:

CONFIG_NIDD_APN - APN used for NIDD connection

This option specifies the APN to use for the NIDD connection.

CONFIG_NIDD_ALLOC_NEW_CID - Allocate new context identifier for NIDD connection

This option, when enabled, allocates a new PDN context identifier instead of modifying the default. This enables the use of NIDD together with regular IP traffic.

CONFIG_NIDD_PAYLOAD - Payload for NIDD transmission

This option sets the application payload to be sent as data.

Sending traces over UART on an nRF91 Series DK

To send modem traces over UART on an nRF91 Series DK, configuration must be added for the UART device in the devicetree and Kconfig. This is done by adding the modem trace UART snippet when building and programming.

Use the Cellular Monitor app for capturing and analyzing modem traces.

TF-M logging must use the same UART as the application. For more details, see shared TF-M logging.

Building and running

This sample can be found under samples/cellular/nidd in the nRF Connect SDK folder structure.

When built as firmware image for a board target with the */ns variant, the sample has Cortex-M Security Extensions (CMSE) enabled and separates the firmware between Non-Secure Processing Environment (NSPE) and Secure Processing Environment (SPE). Because of this, it automatically includes the Trusted Firmware-M (TF-M). To read more about CMSE, see Processing environments.

To build the sample, follow the instructions in Building an application for your preferred building environment. See also Programming an application for programming steps and Testing and optimization for general information about testing and debugging in the nRF Connect SDK.

Note

When building repository applications in the SDK repositories, building with sysbuild is enabled by default. If you work with out-of-tree freestanding applications, you need to manually pass the --sysbuild parameter to every build command or configure west to always use it.

Testing

After programming the sample to your development kit, complete the following steps to test it:

  1. Connect the kit to the computer using a USB cable. The kit is assigned a COM port (Windows) or ttyACM device (Linux), which is visible in the Device Manager.

  2. Connect to the kit with a terminal emulator (for example, nRF Connect Serial Terminal). See Testing and optimization for the required settings and steps.

  3. Observe that the sample starts and shows the following output from the device. Note that this is an example, and the output need not be identical to your observed output.

    NIDD sample started
    Configured Non-IP for APN "iot.nidd"
    LTE cell changed: Cell ID: 21657858, Tracking area: 40401
    RRC mode: Connected
    Network registration status: Connected - roaming
    Get PDN ID 0
    Created socket 0
    Sent 13 bytes
    Received 14 bytes: Hello, Device!
    Closed socket 0
    LTE cell changed: Cell ID: -1, Tracking area: -1
    RRC mode: Idle
    NIDD sample done
    

Dependencies

This sample uses the following nRF Connect SDK library:

It uses the following sdk-nrfxlib library:

The sample also uses the following secure firmware component: