Wi-Fi Provisioning Service

This library implements a Bluetooth® GATT service for Wi-Fi® provisioning. It is to be used with the Wi-Fi: Bluetooth LE based provision sample. The Wi-Fi Provisioning Service forms a complete reference solution, together with the mobile application. For details, see the Wi-Fi: Bluetooth LE based provision sample documentation.

Overview

The service is divided into three parts:

  • GATT service interface: Defines GATT service and provides an interface for the configurator to exchange messages.

  • Task and event handling component: Handles provisioning-related tasks and events.

  • Configuration management component: Manages the provisioning data (in RAM and flash) accessed by multiple threads.

Service declaration

The Wi-Fi Provisioning Service is instantiated as a primary service. Set the service UUID value as defined in the following table.

Service name

UUID

Wi-Fi Provisioning Service

14387800-130c-49e7-b877-2881c89cb258

Service characteristics

The UUID value of characteristics are defined in the following table.

Characteristic name

UUID

Information

14387801-130c-49e7-b877-2881c89cb258

Operation Control Point

14387802-130c-49e7-b877-2881c89cb258

Data Out

14387803-130c-49e7-b877-2881c89cb258

The characteristic requirements of the Wi-Fi Provisioning Service are shown in the following table.

Characteristic name

Requirement

Mandatory properties

Optional properties

Security permissions

Information

Mandatory

Read

No security required

Operation Control Point

Mandatory

Indicate, Write

Encryption required

Operation Control Point - Client Characteristic Configuration descriptor

Mandatory

Read, Write

Encryption required

Data Out

Mandatory

Notify

Encryption required

Data Out - Client Characteristic Configuration descriptor

Mandatory

Read, Write

Encryption required

The purpose of each characteristic is as follows:

  • Information: For client to get Info message from server.

  • Operation Control Point: For client to send Request message to server, and server to send Response message to client.

  • Data Out: For server to send Result message to the client.

Task and event handling

The Wi-Fi Provisioning Service uses Protocol Buffers to define platform-independent message formats. These definitions are available as .proto files in the code.

The service also uses nanopb to convert encoded platform-independent messages to and from C language.

The device performs actions according to messages it exchanges with a configurator (the peer that sends the message, such as a smartphone running the nRF Wi-Fi Provisioner app listed in Requirements).

Message types

The service uses four message types:

  • Info: Allows the configurator to know the capability of a device before the provisioning process happens.

    The configurator reads this message before sending any other messages. The info message contains a version field.

  • Request: Contains a command and configuration.

    The device takes action based on the command and applies the configuration if one is given.

    The following table details the five commands that the service uses.

    Command

    Description

    Notes

    GET_STATUS

    Get the status of the device, such as provisioning state, Wi-Fi connection state, and more

    START_SCAN

    Trigger an access point (AP) scan

    scan_params is optional

    STOP_SCAN

    Stop AP scan

    SET_CONFIG

    Store Wi-Fi configuration and connect to an AP

    config is required

    FORGET_CONFIG

    Erase the configuration and disconnect

  • Response: Contains the command to which it is responding, the operation result, and any other data.

    The device sends any additional data associated with this command to the configurator in a Result message.

    The Response message contains one of following response codes:

    • SUCCESS: The operation is dispatched successfully.

    • INVALID_ARGUMENT: The argument is invalid.

    • INVALID_PROTO: The message cannot be encoded or decoded.

    • INTERNAL_ERROR: The operation cannot be dispatched properly.

    If the command is GET_STATUS, the response includes some or all of the following fields:

    • state: Describes the Wi-Fi connection state according to values defined in the common.proto file.

    • provisioning_info: Includes Wi-Fi provisioning information stored in the non-volatile memory (NVM) of the device.

    • connection_info: Includes Wi-Fi connection details.

    • scan_info: Includes the parameters used for the AP scan.

  • Result: Carries asynchronous data about the operation status.

    • If the command is START_SCAN, the result message sent to the configurator contains information about the AP. Each Result contains information related to one AP.

    • If the command is SET_CONFIG, when the Wi-Fi status changes (for example, from disconnected to connected), the configurator receives a result message with the new status. Meanwhile, the Wi-Fi credentials are stored in the non-volatile memory of the device.

See all definitions in the .subsys/bluetooth/services/wifi_prov/proto/common.proto file.

Operations

The message sequence is the same for all operations, with variations depending on the command:

  1. The configurator sends an encoded Request message with a command to the device.

  2. The device carries out the command.

  3. The device sends a Response message to the configurator.

  4. For some operations, the device also sends a Result message to the configurator with any additional data generated or reported.

See Message types for more information on the commands and additional parameters.

Configuration management

The configuration management component manages Wi-Fi configurations. It uses the Wi-Fi credentials library to handle the configurations in flash. The component has one slot in RAM to save the configurations.

You can save the configuration in flash or RAM during provisioning.

API documentation

Header file: include/bluetooth/services/wifi_provisioning.h
Source files: subsys/bluetooth/services/wifi_prov
group bt_wifi_prov

API for the Wi-Fi Provisioning Service.

Defines

BT_UUID_PROV_VAL
BT_UUID_PROV
BT_UUID_PROV_INFO_VAL
BT_UUID_PROV_INFO
BT_UUID_PROV_CONTROL_POINT_VAL
BT_UUID_PROV_CONTROL_POINT
BT_UUID_PROV_DATA_OUT_VAL
BT_UUID_PROV_DATA_OUT
PROV_SVC_VER

Firmware version.

Functions

bool bt_wifi_prov_state_get(void)

Get provisioning state.

Returns:

true if device is provisioned, false otherwise.

int bt_wifi_prov_init(void)

Initialize the provisioning module.

Returns:

0 if module initialized successfully, negative error code otherwise.