Regulator Interface. More...

Modules
	ADP5360 Devicetree helpers.

	AXP192 Devicetree helpers.

	Devicetree helpers

	MAX20335 Devicetree helpers.

	NPM1100 Devicetree helpers.

	NPM1300 Devicetree helpers.

	NPM6001 Devicetree helpers.

	Regulator Parent Interface
	Regulator Parent Interface.

	nRF5X regulator devicetree helpers.

Typedefs
typedef uint8_t	regulator_dvs_state_t
	Opaque type to store regulator DVS states.

typedef uint8_t	regulator_mode_t
	Opaque type to store regulator modes.

typedef uint8_t	regulator_error_flags_t
	Opaque bit map for regulator error flags (see REGULATOR_ERRORS)

Functions
int	regulator_enable (const struct device *dev)
	Enable a regulator.

bool	regulator_is_enabled (const struct device *dev)
	Check if a regulator is enabled.

int	regulator_disable (const struct device *dev)
	Disable a regulator.

static unsigned int	regulator_count_voltages (const struct device *dev)
	Obtain the number of supported voltage levels.

static int	regulator_list_voltage (const struct device dev, unsigned int idx, int32_t volt_uv)
	Obtain the value of a voltage given an index.

bool	regulator_is_supported_voltage (const struct device *dev, int32_t min_uv, int32_t max_uv)
	Check if a voltage within a window is supported.

int	regulator_set_voltage (const struct device *dev, int32_t min_uv, int32_t max_uv)
	Set the output voltage.

static int	regulator_get_voltage (const struct device dev, int32_t volt_uv)
	Obtain output voltage.

static unsigned int	regulator_count_current_limits (const struct device *dev)
	Obtain the number of supported current limit levels.

static int	regulator_list_current_limit (const struct device dev, unsigned int idx, int32_t current_ua)
	Obtain the value of a current limit given an index.

int	regulator_set_current_limit (const struct device *dev, int32_t min_ua, int32_t max_ua)
	Set output current limit.

static int	regulator_get_current_limit (const struct device dev, int32_t curr_ua)
	Get output current limit.

int	regulator_set_mode (const struct device *dev, regulator_mode_t mode)
	Set mode.

static int	regulator_get_mode (const struct device dev, regulator_mode_t mode)
	Get mode.

static int	regulator_set_active_discharge (const struct device *dev, bool active_discharge)
	Set active discharge setting.

static int	regulator_get_active_discharge (const struct device dev, bool active_discharge)
	Get active discharge setting.

static int	regulator_get_error_flags (const struct device dev, regulator_error_flags_t flags)
	Get active error flags.

Regulator error flags.

#define	REGULATOR_ERROR_OVER_VOLTAGE BIT(0)
	Voltage is too high.

#define	REGULATOR_ERROR_OVER_CURRENT BIT(1)
	Current is too high.

#define	REGULATOR_ERROR_OVER_TEMP BIT(2)
	Temperature is too high.

Detailed Description

Regulator Interface.

Since: 2.4

Version: 0.1.0

Macro Definition Documentation

◆ REGULATOR_ERROR_OVER_CURRENT

#define REGULATOR_ERROR_OVER_CURRENT BIT(1)

#include <zephyr/drivers/regulator.h>

Current is too high.

◆ REGULATOR_ERROR_OVER_TEMP

#define REGULATOR_ERROR_OVER_TEMP BIT(2)

#include <zephyr/drivers/regulator.h>

Temperature is too high.

◆ REGULATOR_ERROR_OVER_VOLTAGE

#define REGULATOR_ERROR_OVER_VOLTAGE BIT(0)

#include <zephyr/drivers/regulator.h>

Voltage is too high.

Typedef Documentation

◆ regulator_dvs_state_t

typedef uint8_t regulator_dvs_state_t

#include <zephyr/drivers/regulator.h>

Opaque type to store regulator DVS states.

◆ regulator_error_flags_t

typedef uint8_t regulator_error_flags_t

#include <zephyr/drivers/regulator.h>

Opaque bit map for regulator error flags (see REGULATOR_ERRORS)

◆ regulator_mode_t

typedef uint8_t regulator_mode_t

#include <zephyr/drivers/regulator.h>

Opaque type to store regulator modes.

Function Documentation

◆ regulator_count_current_limits()

static unsigned int regulator_count_current_limits ( const struct device * dev )

inlinestatic

#include <zephyr/drivers/regulator.h>

Obtain the number of supported current limit levels.

Each current limit level supported by a regulator gets an index, starting from zero. The total number of supported current limit levels can be used together with regulator_list_current_limit() to list all supported current limit levels.

Parameters

dev	Regulator device instance.

Returns: Number of supported current limits.

◆ regulator_count_voltages()

static unsigned int regulator_count_voltages ( const struct device * dev )

inlinestatic

#include <zephyr/drivers/regulator.h>

Obtain the number of supported voltage levels.

Each voltage level supported by a regulator gets an index, starting from zero. The total number of supported voltage levels can be used together with regulator_list_voltage() to list all supported voltage levels.

Parameters

dev	Regulator device instance.

Returns: Number of supported voltages.

◆ regulator_disable()

int regulator_disable ( const struct device * dev )

#include <zephyr/drivers/regulator.h>

Disable a regulator.

Release a regulator after a previous regulator_enable() completed successfully. Regulators that are always on, or configured in devicetree with regulator-always-on will always stay enabled, and so this function will always succeed.

This must be invoked at most once for each successful regulator_enable().

Parameters

dev	Regulator device instance.

Return values

0	If regulator has been successfully disabled.
-errno	Negative errno in case of failure.
-ENOTSUP	If regulator disablement can not be controlled.

◆ regulator_enable()

int regulator_enable ( const struct device * dev )

#include <zephyr/drivers/regulator.h>

Enable a regulator.

Reference-counted request that a regulator be turned on. A regulator is considered "on" when it has reached a stable/usable state. Regulators that are always on, or configured in devicetree with regulator-always-on will always stay enabled, and so this function will always succeed.

Parameters

dev	Regulator device instance

Return values

0	If regulator has been successfully enabled.
-errno	Negative errno in case of failure.
-ENOTSUP	If regulator enablement can not be controlled.

◆ regulator_get_active_discharge()

static int regulator_get_active_discharge	(	const struct device *	dev,
		bool *	active_discharge
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Get active discharge setting.

Parameters

	dev	Regulator device instance.
[out]	active_discharge	Where active discharge will be stored.

Return values

0	If successful.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_get_current_limit()

static int regulator_get_current_limit	(	const struct device *	dev,
		int32_t *	curr_ua
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Get output current limit.

Parameters

	dev	Regulator device instance.
[out]	curr_ua	Where output current limit will be stored.

Return values

0	If successful.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_get_error_flags()

static int regulator_get_error_flags	(	const struct device *	dev,
		regulator_error_flags_t *	flags
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Get active error flags.

Parameters

	dev	Regulator device instance.
[out]	flags	Where error flags will be stored.

Return values

0	If successful.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_get_mode()

static int regulator_get_mode	(	const struct device *	dev,
		regulator_mode_t *	mode
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Get mode.

Parameters

	dev	Regulator device instance.
[out]	mode	Where mode will be stored.

Return values

0	If successful.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_get_voltage()

static int regulator_get_voltage	(	const struct device *	dev,
		int32_t *	volt_uv
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Obtain output voltage.

Parameters

	dev	Regulator device instance.
[out]	volt_uv	Where configured output voltage will be stored.

Return values

0	If successful
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_is_enabled()

bool regulator_is_enabled ( const struct device * dev )

#include <zephyr/drivers/regulator.h>

Check if a regulator is enabled.

Parameters

dev	Regulator device instance.

Return values

true	If regulator is enabled.
false	If regulator is disabled.

◆ regulator_is_supported_voltage()

bool regulator_is_supported_voltage	(	const struct device *	dev,
		int32_t	min_uv,
		int32_t	max_uv
	)

#include <zephyr/drivers/regulator.h>

Check if a voltage within a window is supported.

Parameters

dev	Regulator device instance.
min_uv	Minimum voltage in microvolts.
max_uv	maximum voltage in microvolts.

Return values

true	If voltage is supported.
false	If voltage is not supported.

◆ regulator_list_current_limit()

static int regulator_list_current_limit	(	const struct device *	dev,
		unsigned int	idx,
		int32_t *	current_ua
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Obtain the value of a current limit given an index.

Each current limit level supported by a regulator gets an index, starting from zero. Together with regulator_count_current_limits(), this function can be used to iterate over all supported current limits.

Parameters

	dev	Regulator device instance.
	idx	Current index.
[out]	current_ua	Where current for the given `index` will be stored, in microamps.

Return values

0	If `index` corresponds to a supported current limit.
-EINVAL	If `index` does not correspond to a supported current limit.

◆ regulator_list_voltage()

static int regulator_list_voltage	(	const struct device *	dev,
		unsigned int	idx,
		int32_t *	volt_uv
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Obtain the value of a voltage given an index.

Each voltage level supported by a regulator gets an index, starting from zero. Together with regulator_count_voltages(), this function can be used to iterate over all supported voltages.

Parameters

	dev	Regulator device instance.
	idx	Voltage index.
[out]	volt_uv	Where voltage for the given `index` will be stored, in microvolts.

Return values

0	If `index` corresponds to a supported voltage.
-EINVAL	If `index` does not correspond to a supported voltage.

◆ regulator_set_active_discharge()

static int regulator_set_active_discharge	(	const struct device *	dev,
		bool	active_discharge
	)

inlinestatic

#include <zephyr/drivers/regulator.h>

Set active discharge setting.

Parameters

dev	Regulator device instance.
active_discharge	Active discharge enable or disable.

Return values

0	If successful.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_set_current_limit()

int regulator_set_current_limit	(	const struct device *	dev,
		int32_t	min_ua,
		int32_t	max_ua
	)

#include <zephyr/drivers/regulator.h>

Set output current limit.

The output current limit will be configured to the closest supported output current limit. regulator_get_current_limit() can be used to obtain the actual configured current limit. Current may be limited using current-min-microamp and/or current-max-microamp in Devicetree.

Parameters

dev	Regulator device instance.
min_ua	Minimum acceptable current limit in microamps.
max_ua	Maximum acceptable current limit in microamps.

Return values

0	If successful.
-EINVAL	If the given current limit window is not valid.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_set_mode()

int regulator_set_mode	(	const struct device *	dev,
		regulator_mode_t	mode
	)

#include <zephyr/drivers/regulator.h>

Set mode.

Regulators can support multiple modes in order to permit different voltage configuration or better power savings. This API will apply a mode for the regulator. Allowed modes may be limited using regulator-allowed-modes devicetree property.

Parameters

dev	Regulator device instance.
mode	Mode to select for this regulator.

Return values

0	If successful.
-ENOTSUP	If mode is not supported.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

◆ regulator_set_voltage()

int regulator_set_voltage	(	const struct device *	dev,
		int32_t	min_uv,
		int32_t	max_uv
	)

#include <zephyr/drivers/regulator.h>

Set the output voltage.

The output voltage will be configured to the closest supported output voltage. regulator_get_voltage() can be used to obtain the actual configured voltage. The voltage will be applied to the active or selected mode. Output voltage may be limited using regulator-min-microvolt and/or regulator-max-microvolt in devicetree.

Parameters

dev	Regulator device instance.
min_uv	Minimum acceptable voltage in microvolts.
max_uv	Maximum acceptable voltage in microvolts.

Return values

0	If successful.
-EINVAL	If the given voltage window is not valid.
-ENOSYS	If function is not implemented.
-errno	In case of any other error.

Modules

Typedefs

Functions

Regulator error flags.

Detailed Description

Macro Definition Documentation

◆ REGULATOR_ERROR_OVER_CURRENT

◆ REGULATOR_ERROR_OVER_TEMP

◆ REGULATOR_ERROR_OVER_VOLTAGE

Typedef Documentation

◆ regulator_dvs_state_t

◆ regulator_error_flags_t

◆ regulator_mode_t

Function Documentation

◆ regulator_count_current_limits()

◆ regulator_count_voltages()

◆ regulator_disable()

◆ regulator_enable()

◆ regulator_get_active_discharge()

◆ regulator_get_current_limit()

◆ regulator_get_error_flags()

◆ regulator_get_mode()

◆ regulator_get_voltage()

◆ regulator_is_enabled()

◆ regulator_is_supported_voltage()

◆ regulator_list_current_limit()

◆ regulator_list_voltage()

◆ regulator_set_active_discharge()

◆ regulator_set_current_limit()

◆ regulator_set_mode()

◆ regulator_set_voltage()