◆ nrf_wifi_umac_commands

#include <nrf_wifi/fw_if/umac_if/inc/fw/host_rpu_umac_if.h>

The host can send the following commands to the RPU.

Enumerator
NRF_WIFI_UMAC_CMD_TRIGGER_SCAN	Trigger a new scan nrf_wifi_umac_cmd_scan
NRF_WIFI_UMAC_CMD_GET_SCAN_RESULTS	Request for scan results nrf_wifi_umac_cmd_get_scan_results
NRF_WIFI_UMAC_CMD_AUTHENTICATE	Send authentication request to AP nrf_wifi_umac_cmd_auth
NRF_WIFI_UMAC_CMD_ASSOCIATE	Send associate request to AP nrf_wifi_umac_cmd_assoc
NRF_WIFI_UMAC_CMD_DEAUTHENTICATE	Send deauthentication request to AP nrf_wifi_umac_cmd_disconn
NRF_WIFI_UMAC_CMD_SET_WIPHY	Set wiphy parameters nrf_wifi_umac_cmd_set_wiphy
NRF_WIFI_UMAC_CMD_NEW_KEY	Add new key nrf_wifi_umac_cmd_key
NRF_WIFI_UMAC_CMD_DEL_KEY	Delete key nrf_wifi_umac_cmd_key
NRF_WIFI_UMAC_CMD_SET_KEY	Set default key to use nrf_wifi_umac_cmd_set_key
NRF_WIFI_UMAC_CMD_GET_KEY	Unused
NRF_WIFI_UMAC_CMD_NEW_BEACON	Unused
NRF_WIFI_UMAC_CMD_SET_BEACON	Change the beacon on an AP interface nrf_wifi_umac_cmd_set_beacon
NRF_WIFI_UMAC_CMD_SET_BSS	Set the BSS nrf_wifi_umac_cmd_set_bss
NRF_WIFI_UMAC_CMD_START_AP	Start soft AP operation on an AP interface nrf_wifi_umac_cmd_start_ap
NRF_WIFI_UMAC_CMD_STOP_AP	Stop soft AP operation nrf_wifi_umac_cmd_stop_ap
NRF_WIFI_UMAC_CMD_NEW_INTERFACE	Create new interface nrf_wifi_umac_cmd_add_vif
NRF_WIFI_UMAC_CMD_SET_INTERFACE	Change interface configuration nrf_wifi_umac_cmd_chg_vif_attr
NRF_WIFI_UMAC_CMD_DEL_INTERFACE	Delete interface nrf_wifi_umac_cmd_del_vif
NRF_WIFI_UMAC_CMD_SET_IFFLAGS	Change interface flags nrf_wifi_umac_cmd_chg_vif_state
NRF_WIFI_UMAC_CMD_NEW_STATION	Add a new station nrf_wifi_umac_cmd_add_sta
NRF_WIFI_UMAC_CMD_DEL_STATION	Delete station nrf_wifi_umac_cmd_del_sta
NRF_WIFI_UMAC_CMD_SET_STATION	Change station info nrf_wifi_umac_cmd_chg_sta
NRF_WIFI_UMAC_CMD_GET_STATION	Get station info nrf_wifi_umac_cmd_get_sta
NRF_WIFI_UMAC_CMD_START_P2P_DEVICE	Start the P2P device nrf_wifi_cmd_start_p2p
NRF_WIFI_UMAC_CMD_STOP_P2P_DEVICE	Stop the P2P device nrf_wifi_umac_cmd_stop_p2p_dev
NRF_WIFI_UMAC_CMD_REMAIN_ON_CHANNEL	Remain awake on the specified channel nrf_wifi_umac_cmd_remain_on_channel
NRF_WIFI_UMAC_CMD_CANCEL_REMAIN_ON_CHANNEL	Cancel a pending ROC duration nrf_wifi_umac_cmd_cancel_remain_on_channel
NRF_WIFI_UMAC_CMD_SET_CHANNEL	Unused
NRF_WIFI_UMAC_CMD_RADAR_DETECT	Unused
NRF_WIFI_UMAC_CMD_REGISTER_FRAME	Whitelist filter based on frame types nrf_wifi_umac_cmd_mgmt_frame_reg
NRF_WIFI_UMAC_CMD_FRAME	Send a management frame nrf_wifi_umac_cmd_mgmt_tx
NRF_WIFI_UMAC_CMD_JOIN_IBSS	Unused
NRF_WIFI_UMAC_CMD_WIN_STA_CONNECT	Unused
NRF_WIFI_UMAC_CMD_SET_POWER_SAVE	Power save Enable/Disable nrf_wifi_umac_cmd_set_power_save
NRF_WIFI_UMAC_CMD_SET_WOWLAN	Unused
NRF_WIFI_UMAC_CMD_SUSPEND	Unused
NRF_WIFI_UMAC_CMD_RESUME	Unused
NRF_WIFI_UMAC_CMD_SET_QOS_MAP	QOS map nrf_wifi_umac_cmd_set_qos_map
NRF_WIFI_UMAC_CMD_GET_CHANNEL	Get Channel info nrf_wifi_umac_cmd_get_channel
NRF_WIFI_UMAC_CMD_GET_TX_POWER	Get Tx power level nrf_wifi_umac_cmd_get_tx_power
NRF_WIFI_UMAC_CMD_GET_INTERFACE	Get interface nrf_wifi_cmd_get_interface
NRF_WIFI_UMAC_CMD_GET_WIPHY	Get Wiphy info nrf_wifi_cmd_get_wiphy
NRF_WIFI_UMAC_CMD_GET_IFHWADDR	Get hardware address nrf_wifi_cmd_get_ifhwaddr
NRF_WIFI_UMAC_CMD_SET_IFHWADDR	Set hardware address nrf_wifi_cmd_set_ifhwaddr
NRF_WIFI_UMAC_CMD_GET_REG	Get regulatory domain nrf_wifi_umac_cmd_get_reg
NRF_WIFI_UMAC_CMD_SET_REG	Unused
NRF_WIFI_UMAC_CMD_REQ_SET_REG	Set regulatory domain nrf_wifi_cmd_req_set_reg
NRF_WIFI_UMAC_CMD_CONFIG_UAPSD	Config UAPSD nrf_wifi_umac_cmd_config_uapsd
NRF_WIFI_UMAC_CMD_CONFIG_TWT	Config TWT nrf_wifi_umac_cmd_config_twt
NRF_WIFI_UMAC_CMD_TEARDOWN_TWT	Teardown TWT nrf_wifi_umac_cmd_teardown_twt
NRF_WIFI_UMAC_CMD_ABORT_SCAN	Abort scan nrf_wifi_umac_cmd_abort_scan
NRF_WIFI_UMAC_CMD_MCAST_FILTER	Multicast filter nrf_wifi_umac_cmd_mcast_filter
NRF_WIFI_UMAC_CMD_CHANGE_MACADDR	Change macaddress nrf_wifi_umac_cmd_change_macaddr
NRF_WIFI_UMAC_CMD_SET_POWER_SAVE_TIMEOUT	Set powersave timeout nrf_wifi_umac_cmd_set_power_save_timeout
NRF_WIFI_UMAC_CMD_GET_CONNECTION_INFO	Get connection information nrf_wifi_umac_cmd_conn_info
NRF_WIFI_UMAC_CMD_GET_POWER_SAVE_INFO	Get power save information nrf_wifi_umac_cmd_get_power_save_info
NRF_WIFI_UMAC_CMD_SET_LISTEN_INTERVAL	Set listen interval nrf_wifi_umac_cmd_set_listen_interval
NRF_WIFI_UMAC_CMD_CONFIG_EXTENDED_PS	Configure extended power save nrf_wifi_umac_cmd_config_extended_ps
NRF_WIFI_UMAC_CMD_CONFIG_QUIET_PERIOD	Configure quiet period nrf_wifi_umac_cmd_config_quiet_period