esb.h File Reference

#include <stdbool.h>
#include <errno.h>
#include <nrf.h>
#include <hal/nrf_radio.h>
#include <zephyr/sys/util.h>
#include <zephyr/types.h>

Go to the source code of this file.

Data Structures
struct	esb_payload
	Enhanced ShockBurst payload. More...
struct	esb_evt
	Enhanced ShockBurst event. More...
struct	esb_config
	Main configuration structure for the module. More...

Macros
#define	ESB_DEFAULT_CONFIG
	Default radio parameters.
#define	ESB_LEGACY_CONFIG
	Default legacy radio parameters.
#define	ESB_CREATE_PAYLOAD(_pipe, ...)
	Macro to create an initializer for a TX data packet.

Typedefs
typedef void(*	esb_event_handler) (const struct esb_evt *event)
	Event handler prototype.

Enumerations
enum	esb_protocol { ESB_PROTOCOL_ESB , ESB_PROTOCOL_ESB_DPL }
	Enhanced ShockBurst protocols. More...
enum	esb_mode { ESB_MODE_PTX , ESB_MODE_PRX }
	Enhanced ShockBurst modes. More...
enum	esb_bitrate { ESB_BITRATE_1MBPS = NRF_RADIO_MODE_NRF_1MBIT , ESB_BITRATE_2MBPS = NRF_RADIO_MODE_NRF_2MBIT , ESB_BITRATE_250KBPS = NRF_RADIO_MODE_NRF_250KBIT , ESB_BITRATE_1MBPS_BLE = NRF_RADIO_MODE_BLE_1MBIT }
	Enhanced ShockBurst bitrate modes. More...
enum	esb_crc { ESB_CRC_16BIT = RADIO_CRCCNF_LEN_Two , ESB_CRC_8BIT = RADIO_CRCCNF_LEN_One , ESB_CRC_OFF = RADIO_CRCCNF_LEN_Disabled }
	Enhanced ShockBurst CRC modes. More...
enum	esb_tx_power
	Enhanced ShockBurst radio transmission power modes. More...
enum	esb_tx_mode { ESB_TXMODE_AUTO , ESB_TXMODE_MANUAL , ESB_TXMODE_MANUAL_START }
	Enhanced ShockBurst transmission modes. More...
enum	esb_evt_id { ESB_EVENT_TX_SUCCESS , ESB_EVENT_TX_FAILED , ESB_EVENT_RX_RECEIVED }
	Enhanced ShockBurst event IDs. More...

Functions
int	esb_init (const struct esb_config *config)
	Initialize the Enhanced ShockBurst module.
int	esb_suspend (void)
	Suspend the Enhanced ShockBurst module.
void	esb_disable (void)
	Disable the Enhanced ShockBurst module.
bool	esb_is_idle (void)
	Check if the Enhanced ShockBurst module is idle.
int	esb_write_payload (const struct esb_payload *payload)
	Write a payload for transmission or acknowledgement.
int	esb_read_rx_payload (struct esb_payload *payload)
	Read a payload.
int	esb_start_tx (void)
	Start transmitting data.
int	esb_start_rx (void)
	Start receiving data.
int	esb_stop_rx (void)
	Stop data reception.
int	esb_flush_tx (void)
	Flush the TX buffer.
int	esb_pop_tx (void)
	Pop the first item from the TX buffer.
bool	esb_tx_full (void)
	Check if there is some free space left in TX FIFO.
int	esb_flush_rx (void)
	Flush the RX buffer.
int	esb_set_address_length (uint8_t length)
	Set the length of the address.
int	esb_set_base_address_0 (const uint8_t *addr)
	Set the base address for pipe 0.
int	esb_set_base_address_1 (const uint8_t *addr)
	Set the base address for pipe 1 to pipe 7.
int	esb_set_prefixes (const uint8_t *prefixes, uint8_t num_pipes)
	Set the number of pipes and the pipe prefix addresses.
int	esb_enable_pipes (uint8_t enable_mask)
	Enable select pipes.
int	esb_update_prefix (uint8_t pipe, uint8_t prefix)
	Update pipe prefix.
int	esb_set_rf_channel (uint32_t channel)
	Set the channel to use for the radio.
int	esb_get_rf_channel (uint32_t *channel)
	Get the current radio channel.
int	esb_set_tx_power (int8_t tx_output_power)
	Set the radio output power.
int	esb_set_retransmit_delay (uint16_t delay)
	Set the packet retransmit delay.
int	esb_set_retransmit_count (uint16_t count)
	Set the number of retransmission attempts.
int	esb_set_bitrate (enum esb_bitrate bitrate)
	Set the radio bitrate.
int	esb_reuse_pid (uint8_t pipe)
	Reuse a packet ID for a specific pipe.