I3C Target Device API

I3C Target Device API. More...

Data Structures
struct	i3c_config_target
	Configuration parameters for I3C hardware to act as target device. More...
struct	i3c_target_config
	Structure describing a device that supports the I3C target API. More...
struct	i3c_target_callbacks
struct	i3c_target_driver_api

Functions
static int	i3c_target_tx_write (const struct device *dev, uint8_t *buf, uint16_t len)
	Writes to the target's TX FIFO.
static int	i3c_target_register (const struct device *dev, struct i3c_target_config *cfg)
	Registers the provided config as target device of a controller.
static int	i3c_target_unregister (const struct device *dev, struct i3c_target_config *cfg)
	Unregisters the provided config as target device.

Detailed Description

I3C Target Device API.

Function Documentation

i3c_target_register()

static int i3c_target_register ( const struct device *  dev, struct i3c_target_config *  cfg  )

inlinestatic

#include <zephyr/drivers/i3c/target_device.h>

Registers the provided config as target device of a controller.

Enable I3C target mode for the dev I3C bus driver using the provided config struct (cfg) containing the functions and parameters to send bus events. The I3C target will be registered at the address provided as i3c_target_config::address struct member. Any I3C bus events related to the target mode will be passed onto I3C target device driver via a set of callback functions provided in the 'callbacks' struct member.

Most of the existing hardware allows simultaneous support for master and target mode. This is however not guaranteed.

Parameters

dev	Pointer to the device structure for an I3C controller driver configured in target mode.
cfg	Config struct with functions and parameters used by the I3C target driver to send bus events

Return values

0	Is successful
-EINVAL	If parameters are invalid
-EIO	General input / output error.
-ENOSYS	If target mode is not implemented

i3c_target_tx_write()

static int i3c_target_tx_write ( const struct device *  dev, uint8_t *  buf, uint16_t  len  )

inlinestatic

#include <zephyr/drivers/i3c/target_device.h>

Writes to the target's TX FIFO.

Write to the TX FIFO dev I3C bus driver using the provided buffer and length. Some I3C targets will NACK read requests until data is written to the TX FIFO. This function will write as much as it can to the FIFO return the total number of bytes written. It is then up to the application to utalize the target callbacks to write the remaining data. Negative returns indicate error.

Most of the existing hardware allows simultaneous support for master and target mode. This is however not guaranteed.

Parameters

dev	Pointer to the device structure for an I3C controller driver configured in target mode.
buf	Pointer to the buffer
len	Length of the buffer

Return values

Total	number of bytes written
-ENOTSUP	Not in Target Mode
-ENOSPC	No space in Tx FIFO
-ENOSYS	If target mode is not implemented

i3c_target_unregister()

static int i3c_target_unregister ( const struct device *  dev, struct i3c_target_config *  cfg  )

inlinestatic

#include <zephyr/drivers/i3c/target_device.h>

Unregisters the provided config as target device.

This routine disables I3C target mode for the dev I3C bus driver using the provided config struct (cfg) containing the functions and parameters to send bus events.

Parameters

dev	Pointer to the device structure for an I3C controller driver configured in target mode.
cfg	Config struct with functions and parameters used by the I3C target driver to send bus events

Return values

0	Is successful
-EINVAL	If parameters are invalid
-ENOSYS	If target mode is not implemented