ST STM32L1 Discovery

Overview

The two generations of the STM32L1 Discovery development boards come with an integrated ST-LINK/V2 debugger and programmer. The boards have a 24-segment LCD and a touch slider, along with two user LEDs and a user button. Support circuitry for measuring power consumption is also available. It also comes with a comprehensive STM32 software HAL library and various packaged software examples.

There are two variants of the board:

  • STM32LDISCOVERY targets STM32L152RBT6, with 128K flash, 16K RAM, 4K EEPROM

  • STM32L152CDISCOVERY targets STM32L152RCT6, with 256K flash, 32K RAM, 8K EEPROM

The STM32LDISCOVERY is no longer sold, but was widely available. stm32l1_disco configuration enables support for STM32LDISCOVERY board and stm32l152c_disco configuration enables support for STM32L152CDISCOVERY board.

STM32LDISCOVERY

More information about the board can be found at the STM32LDISCOVERY website [1].

Hardware

The STM32 Discovery board features:

  • On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone ST-LINK/V2 (with SWD connector for programming and debugging)

  • Board power supply: through USB bus or from an external 5 V supply voltage

  • External application power supply: 3 V and 5 V

  • Four LEDs:

    • LD1 (red) for 3.3 V power on

    • LD2 (red/green) for USB communication

    • LD3 (green) for PC9 output

    • LD4 (blue) for PC8 output

  • Two push buttons (user and reset)

  • Extension header for all LQFP64 I/Os for quick connection to prototyping board and easy probing

More information about STM32L151x can be found in the STM32L1x reference manual [2].

Supported Features

The Zephyr stm32l1_disco and stm32l152c_disco board configurations support the following hardware features:

Supported hardware

Interface

Controller

Driver/component

NVIC

on-chip

nested vector interrupt controller

UART

on-chip

serial port-polling serial port-interrupt

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

CLOCK

on-chip

reset and clock control

FLASH

on-chip

flash memory

EEPROM

on-chip

eeprom

WATCHDOG

on-chip

window watchdog

I2C

on-chip

i2c

SPI

on-chip

spi

Other hardware features are not yet supported in this Zephyr port.

The configuration of stm32l1_disco can be found in boards/st/stm32l1_disco/stm32l1_disco_defconfig

Configuration of stm32l152c_disco can be found in boards/st/stm32l1_disco/stm32l152c_disco_defconfig

Connections and IOs

Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as input (with or without pull-up or pull-down), or as peripheral alternate function. Most of the GPIO pins are shared with digital or analog alternate functions. All GPIOs are high current capable except for analog inputs.

Default Zephyr Peripheral Mapping:

  • UART_1_TX : PA9

  • UART_1_RX : PA10

  • UART_2_TX : PA2

  • UART_2_RX : PA3

  • I2C1_SCL : PB6

  • I2C1_SDA : PB7

  • I2C2_SCL : PB10

  • I2C2_SDA : PB11

  • SPI1_NSS : PA4

  • SPI1_SCK : PA5

  • SPI1_MISO : PA6

  • SPI1_MOSI : PA7

  • SPI2_NSS : PB12

  • SPI2_SCK : PB13

  • SPI2_MISO : PB14

  • SPI2_MOSI : PB15

For more details please refer to STM32L1DISCOVERY board User Manual [3].

Programming and Debugging

Applications for the stm32l1_disco board configuration can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Flashing

STM32L1DISCOVERY and STM32L152CDISCOVERY boards include an ST-LINK/V2 embedded debug tool interface. This interface is supported by the openocd version included in the Zephyr SDK.

Flashing an application

Here is an example for the Blinky application.

# From the root of the zephyr repository
west build -b stm32l1_disco samples/basic/blinky
west flash

You will see the LED blinking every second.

Debugging

You can debug an application in the usual way. Here is an example for the Blinky application.

# From the root of the zephyr repository
west build -b stm32l1_disco samples/basic/blinky
west debug

References