FTP AT commands

The following commands list contains FTP related AT commands.

FTP client #XFTP

The #XFTP command allows you to send FTP commands.

Set command

The set command allows you to send FTP commands.

Syntax

#AT#XFTP=<cmd>[,<param1>[<param2]..]]

The <cmd> command is a string, and can be used as follows:

  • AT#XFTP="open",<username>,<password>,<hostname>[,<port>[,<sec_tag>]]

  • AT#XFTP="status"

  • AT#XFTP="ascii"

  • AT#XFTP="binary"

  • AT#XFTP="close"

  • AT#XFTP="verbose","on|off"

  • AT#XFTP="pwd"

  • AT#XFTP="cd",<folder>

  • AT#XFTP="ls"[,<options>[,<folder or file>]]

  • AT#XFTP="mkdir",<folder>

  • AT#XFTP="rmdir",<folder>

  • AT#XFTP="rename",<filename_old>,<filename_new>

  • AT#XFTP="delete",<file>

  • AT#XFTP="get",<file>

  • AT#XFTP="put",<file>[,<data>]

  • AT#XFTP="uput"[,<data>]

  • AT#XFTP="mput",<file>[,<data>]

The values of the parameters depend on the command string used. When using the put,``uput`` and mput commands, if the <data> attribute is not specified, SLM enters slm_data_mode.

Response syntax

The response syntax depends on the commands used.

Examples

AT#XFTP="open",,,"speedtest.tele2.net"
220 (vsFTPd 3.0.3)
200 Always in UTF8 mode.
331 Please specify the password.
230 Login successful.
OK

AT#XFTP="status"
215 UNIX Type: L8
211-FTP server status:
     Connected to ::ffff:202.238.218.44
     Logged in as ftp
     TYPE: ASCII
     No session bandwidth limit
     Session timeout in seconds is 300
     Control connection is plain text
     Data connections will be plain text
     At session startup, client count was 38
     vsFTPd 3.0.3 - secure, fast, stable
211 End of status
OK

AT#XFTP="ascii"
200 Switching to ASCII mode.
OK

AT#XFTP="binary"
200 Switching to Binary mode.
OK

AT#XFTP="close"
221 Goodbye.
OK

Read command

The read command is not supported.

Test command

The test command is not supported.

TFTP client #XTFTP

The #XTFTP command allows you to send TFTP commands.

Note

The maximum supported file size is 2100 bytes. TFTP write request is not supported yet.

Set command

The set command allows you to send TFTP commands based on RFC1350.

Syntax

AT#XTFTP=<op>,<url>,<port>,<file_path>[,<mode>]

  • The <op> parameter can accept one of the following values:

    • 1 - TFTP read request using IP protocol family version 4.

    • Currently not supported 2 - TFTP write request using IP protocol family version 4.

    • 3 - TFTP read request using IP protocol family version 6.

    • Currently not supported 4 - TFTP write request using IP protocol family version 6.

  • The <url> parameter is a string. It indicates the hostname or the IP address of the TFTP server. Its maximum size is 128 bytes. When the parameter is an IP address, it supports both IPv4 and IPv6.

  • The <port> parameter is an unsigned 16-bit integer (0 - 65535). It represents the TFTP service port on the remote server. Default port 69 is applied if this parameter is omitted or set to 0.

  • The <file_path> parameter is a string. It indicates the file path on the TFTP server to read from or write to. Its maximum size is 128 bytes.

  • The <mode> parameter is a string. It indicates the three modes defined in TFTP protocol. Valid values are netascii, octet and mail. The default value octet is applied if this parameter is omitted.

Response syntax

#XTFTP: <size>, "success"
<data>

#XTFTP: <error>, "<error_msg>"

  • The <size> value is an integer. When positive, it indicates the size of data in bytes read from TFTP server.

  • The <data> value is the arbitrary data read from TFTP server.

  • The <error> value is an integer. It is a negative integer based on the type of error.

  • The <error_msg> value is a string. It is the description that corresponds to the <error> value.

Examples

AT#XTFTP=1,"tftp.server",,"test_tftp_fake.txt"
#XTFTP: -4, "remote error"
ERROR

AT#XTFTP=1,"tftp.server",,"test_tftp.txt"
#XTFTP: 45,"success"
Test file for SLM TFTP client.
Does it work?
OK

AT#XTFTP=2,"tftp.server",,"test_upload.txt"
ERROR

Read command

The read command is not supported.

Test command

The test command tests the existence of the command and provides information about the type of its subparameters.

Syntax

AT#XTFTP=?

Examples

AT#XTFTP=?
#XTFTP: (1,2,3,4),<url>,<port>,<file_path>,<mode>
OK