nRF9160: Full modem firmware update using SMP Server

This sample application implements a Simple Management Protocol (SMP) Server, using the SMP transfer encoding with the MCU manager (mcumgr) management protocol, to provide an interface over UART which enables the device to do full modem firmware updates.

For more information about mcumgr and SMP, see Device Management.

Requirements

This sample supports the following development kit:

Hardware platforms

PCA

Board name

Build target

nRF9160 DK

PCA10090

nrf9160dk_nrf9160

nrf9160dk_nrf9160_ns

When built for an _ns build target, the sample is configured to compile and run as a non-secure application. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

Overview

The sample performs the following operations:

  1. It deinitializes the Modem library.

  2. It registers to mcumgr a stat command.

  3. It then registers the commands to upload the firmware and to get the hash.

  4. It finally enters an idle loop, waiting for any communication over the serial line.

The sample also provides a UART overlay that will allow your sample to transfer at a speed of 1M baud, and it enables support for the fmfu_mgmt command group. See Mcumgr based full modem update for more details.

Note

UART is the only transport method supported. RTT is enabled by default to ensure that you can view the log generated by the sample or other subsystems. See How to use RTT for details.

Building and running

This sample can be found under samples/nrf9160/fmfu_smp_svr in the nRF Connect SDK folder structure.

When built as a non-secure firmware image for the _ns build target, the sample automatically includes the Trusted Firmware-M (TF-M).

To build the sample with Visual Studio Code, follow the steps listed on the Building nRF Connect SDK application quick guide page in the nRF Connect for VS Code extension documentation. See Building and programming an application for other building and programming scenarios and Testing and debugging an application for general information about testing and debugging in the nRF Connect SDK.

To use the UART overlay for increasing the transfer speed, add the -DDTC_OVERLAY_FILE=uart.overlay flag to your build. See Providing CMake options for instructions on how to add this flag. For example, when building on the command line, add the UART overlay for nRF9160 DK in the following way:

west build -b nrf9160dk_nrf9160_ns -- -DDTC_OVERLAY_FILE=uart.overlay

Testing

After programming the sample to your development kit, test it by performing the following steps:

  1. Connect the USB cable and power on or reset your nRF9160 DK.

  2. Open a terminal emulator, observe that the sample starts, and then close the terminal emulator.

  3. Call the provided update_modem.py script specifying the COM port, the firmware ZIP file, and the UART baud rate shown in the following examples.

    • If you used the default baud rate:

      python update_modem.py mfw_nrf9160_1.2.2.zip /dev/ttyACM0 115200

    • If you used the -DDTC_OVERLAY_FILE=uart.overlay flag:

      python update_modem.py mfw_nrf9160_1.2.2.zip /dev/ttyACM0 1000000

Sample output

The python script should print the following output:

# nrf9160 modem firmware upgrade over serial port example started.
{
"duration": 406,
"error_code": "Ok",
"operation": "open_uart",
"outcome": "success",
"progress_percentage": 100
}
Programming modem bootloader.
...
Finished with file.
Verifying memory range 1 of 3
Verifying memory range 2 of 3
Verifying memory range 3 of 3
Verification success.
{
"duration": 5,
"error_code": "Ok",
"operation": "close_uart",
"outcome": "success",
"progress_percentage": 100
}
------------------------------------------------------------

Troubleshooting

You can use the mcumgr CLI tool to test if the sample is running correctly, as follows:

 mcumgr --conntype serial --connstring="dev=*COM Port*,baud=*Baudrate*" stat smp_com
 stat group: smp_com
     512 frame_max
     504 pack_max

Dependencies

This sample uses the following nRF Connect SDK libraries:

This sample uses the following sdk-nrfxlib library:

In addition, it uses the following secure firmware component: