Microchip MCP2515 CAN bus shields

Zephyr supports a couple of different shields carrying the Microchip MCP2515 Stand-Alone CAN Controller with SPI Interface.

DFRobot CAN BUS Shield V2.0

Overview

The DFRobot CAN BUS shield supports the Microship MCP2515 stand-alone CAN controller and JTA1050 high speed CAN transceiver. The shield has an Arduino Uno R3 compatible hardware interface.

Hardware

MCP2515
- Stand-Alone CAN 2.0B Controller
- Up to 1Mb/s baud rate
- Standard and extended data and remote frames
- 3x Tx Buffers
- 2x Rx Buffers
- 6x 29-bit Filters
- 2x 29-bit Masks
- Interrupt output
- One shot mode
- High speed SPI interface (10 MHz)
TJA1050
- Fully compatible with the “ISO 11898” standard
- High speed (up to 1 Mbaud)
Connectivity
- Industrial standard DB9 terminal (CAN)
- Screw terminals (CAN)
- Integrated MicroSD socket for data storage (SPI)
- Arduino Uno R3 compatible (SPI)

Name	Function	Usage
A0	None
A1	None
A2	None
A3	None
A4	None
A5	None
D0	RX	Ext. header only
D1	TX	Ext. header only
D2	GPIO_ACTIVE_LOW	MCP2515 - INT
D3	None
D4	SPI-CS	MicroSD
D5	None
D6	None
D7	None
D8	None
D9	None
D10	SPI-CS	MCP2515
D11	SPI-MOSI	MCP2515 / MicroSD
D12	SPI-MISO	MCP2515 / MicroSD
D13	SPI-CLK	MCP2515 / MicroSD
D14	I2C-SDA	Ext. header only
D15	I2C_SCL	Ext. header only

Power Supply
- 3.3V ~ 5V
Components
- Power switch
- Power LED
- RX0BF LED
- RX1BF LED

For more information about the DFRobot CAN-BUS V2.0 shield:

Keyestudio CAN-BUS Shield (KS0411)

Overview

The Keyestudio CAN BUS shield supports the Microship MCP2515 stand-alone CAN controller and MCP2551 high speed CAN transceiver. The shield has an Arduino Uno R3 compatible hardware interface.

Fig. 202 Keyestudio CAN-BUS Shield (KS0411) (Credit: Keyestudio)

Hardware

MCP2515
- Stand-Alone CAN 2.0B Controller
- Up to 1Mb/s baud rate
- Standard and extended data and remote frames
- 3x Tx Buffers
- 2x Rx Buffers
- 6x 29-bit Filters
- 2x 29-bit Masks
- Interrupt output
- One shot mode
- High speed SPI interface (10 MHz)
MCP2551
- Fully compatible with the “ISO 11898” standard
- High speed (up to 1 Mbaud)
Connectivity
- Industrial standard DB9 terminal (CAN)
- Pin headers (CAN)
- Integrated MicroSD socket for data storage (SPI)
- Arduino Uno R3 compatible (SPI)

Name	Function	Usage
A0	None
A1	None
A2	None
A3	None
A4	None
A5	None
D0	RX	Ext. header only
D1	TX	Ext. header only
D2	None
D3	None
D4	None
D5	None
D6	None
D7	None
D8	GPIO_ACTIVE_LOW	MCP2515 - INT
D9	SPI-CS	MicroSD
D10	SPI-CS	MCP2515
D11	SPI-MOSI	MCP2515 / MicroSD
D12	SPI-MISO	MCP2515 / MicroSD
D13	SPI-CLK	MCP2515 / MicroSD
D14	I2C-SDA	Ext. header only
D15	I2C_SCL	Ext. header only

Power Supply
- 5.0VDC

For more information about the Keyestudio CAN-BUS shield:

Programming

Set -DSHIELD=dfrobot_can_bus_v2_0 or -DSHIELD=keyestudio_can_bus_ks0411 when you invoke west build or cmake in your Zephyr application. For example:

Using west:

# From the root of the zephyr repository
west build -b nrf52dk_nrf52832 samples/drivers/can -- -DSHIELD=dfrobot_can_bus_v2_0
west flash

Using CMake and ninja:

# From the root of the zephyr repository
# Use cmake to configure a Ninja-based buildsystem:
cmake -B build -GNinja -DBOARD=nrf52dk_nrf52832 -DSHIELD=dfrobot_can_bus_v2_0 samples/drivers/can

# Now run ninja on the generated build system:
ninja -C build
ninja -C build flash

Using west:

# From the root of the zephyr repository
west build -b nrf52840dk_nrf52840 samples/drivers/can -- -DSHIELD=keyestudio_can_bus_ks0411
west flash

Using CMake and ninja:

# From the root of the zephyr repository
# Use cmake to configure a Ninja-based buildsystem:
cmake -B build -GNinja -DBOARD=nrf52840dk_nrf52840 -DSHIELD=keyestudio_can_bus_ks0411 samples/drivers/can

# Now run ninja on the generated build system:
ninja -C build
ninja -C build flash