X-NUCLEO-IKS01A3: MEMS Inertial and Environmental Multi sensor shield
Overview
The X-NUCLEO-IKS01A3 is a motion MEMS and environmental sensor expansion board for the STM32 Nucleo. It is equipped with Arduino UNO R3 connector layout, and is designed around the LSM6DSO 3D accelerometer and 3D gyroscope, the LIS2MDL 3-axis magnetometer, the LIS2DW12 3-axis accelerometer, the HTS221 humidity and temperature sensor, the LPS22HH pressure sensor, and the STTS751 temperature sensor.
The X-NUCLEO-IKS01A3 interfaces with the STM32 microcontroller via the I2C pin, and it is possible to change the default I2C port.
More information about the board can be found at the X-NUCLEO-IKS01A3 website 1.
Hardware Description
X-NUCLEO-IKS01A3 provides the following key features:
LSM6DO MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±250/±500/±1000/±2000 dps)
LIS2MDL MEMS 3D magnetometer (±50 gauss)
LIS2DW12 MEMS 3D accelerometer (±2/±4/±8/±16 g)
LPS22HH MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
HTS221 capacitive digital relative humidity and temperature
STTS751 Temperature sensor (-40 °C to +125 °C)
DIL24 socket for additional MEMS adapters and other sensors (configurable in I2C or SPI)
I2C sensor hub features on LSM6DSO available
Compatible with STM32 Nucleo boards
Equipped with Arduino UNO R3 connector
RoHS compliant
WEEE compliant
Hardware Configuration
X-NUCLEO-IKS01A3 board connects the various devices on two separate I2C bus:
LIS2DW12 and LSM6DO are on I2C2
LIS2MDL, LPS22HH, HTS221 are STTS751 are on I2C1
X-NUCLEO-IKS01A3 board can be configured in two different ways: Mode 1 and Mode 2
Mode 1: Standard Mode
In standard I2C mode the two buses are connected together. As a consequence, all devices on the shield reside on the same I2C bus and are accessible from the main board thru I2C bus.
The jumper configuration to activate this mode is:
JP7 => 1-2, 3-4 (I2C1 = I2C2, I2Cx=GND)
JP8 => 1-2, 3-4 (I2C1 = I2C2, I2Cx=GND)
Mode 2: SensorHub Mode
In SensorHub mode LSM6DSO and LIS2DW12 are connected to I2C2 and are accessible from the main board. All the other devices are connected to LSM6DSO master thru I2C1.
The jumper configuration to activate this mode is:
JP7 => 2-3 (I2C1 = I2Cx)
JP8 => 2-3 (I2C1 = I2Cx)
More information about X-NUCLEO-IKS01A3 configuration modes can be found in the X-NUCLEO-IKS01A3 user manual 2
Programming
Two samples are provided as examples for x-nucleo-iks01a3 shield:
X-NUCLEO-IKS01A3: shield Standard (Mode 1) sample application, to be used when the shield is configured in Standard Mode
X-NUCLEO-IKS01A3: shield (Mode 2) sample application, to be used when the shield is configured in SensorHub Mode
See also Shields for more details.