Definitions and prototypes for the GAP interface. More...

Modules
	Message Sequence Charts

	Defines

Data Structures
struct	ble_gap_addr_t
	Bluetooth Low Energy address. More...

struct	ble_gap_conn_params_t
	GAP connection parameters. More...

struct	ble_gap_conn_sec_mode_t
	GAP link requirements. More...

struct	ble_gap_conn_sec_t
	GAP connection security status. More...

struct	ble_gap_irk_t
	Identity Resolving Key. More...

struct	ble_gap_whitelist_t
	Whitelist structure. More...

struct	ble_gap_adv_params_t
	GAP advertising parameters. More...

struct	ble_gap_scan_params_t
	GAP scanning parameters. More...

struct	ble_gap_sec_params_t
	GAP security parameters. More...

struct	ble_gap_enc_info_t
	GAP Encryption Information. More...

struct	ble_gap_master_id_t
	GAP Master Identification. More...

struct	ble_gap_id_info_t
	GAP Identity Information. More...

struct	ble_gap_sign_info_t
	GAP Signing Information. More...

struct	ble_gap_evt_connected_t
	Event data for connected event. More...

struct	ble_gap_evt_disconnected_t
	Event data for disconnected event. More...

struct	ble_gap_evt_conn_param_update_t
	Event data for connection parameter update event. More...

struct	ble_gap_evt_sec_params_request_t
	Event data for security parameters request event. More...

struct	ble_gap_evt_sec_info_request_t
	Event data for securito info request event. More...

struct	ble_gap_evt_passkey_display_t
	Event data for passkey display event. More...

struct	ble_gap_evt_auth_key_request_t
	Event data for authentication key request event. More...

struct	ble_gap_sec_levels_t
	Security levels supported. More...

struct	ble_gap_sec_keys_t
	Keys that have been exchanged. More...

struct	ble_gap_evt_auth_status_t
	Event data for authentication status event. More...

struct	ble_gap_evt_conn_sec_update_t
	Event data for connection security update event. More...

struct	ble_gap_evt_timeout_t
	Event data for timeout event. More...

struct	ble_gap_evt_rssi_changed_t
	Event data for advertisement report event. More...

struct	ble_gap_evt_t
	GAP event callback event structure. More...

Enumerations
enum	BLE_GAP_SVCS { SD_BLE_GAP_ADDRESS_SET = 0x70, SD_BLE_GAP_ADDRESS_GET, SD_BLE_GAP_ADV_DATA_SET, SD_BLE_GAP_ADV_START, SD_BLE_GAP_ADV_STOP, SD_BLE_GAP_CONN_PARAM_UPDATE, SD_BLE_GAP_DISCONNECT, SD_BLE_GAP_TX_POWER_SET, SD_BLE_GAP_APPEARANCE_SET, SD_BLE_GAP_APPEARANCE_GET, SD_BLE_GAP_PPCP_SET, SD_BLE_GAP_PPCP_GET, SD_BLE_GAP_DEVICE_NAME_SET, SD_BLE_GAP_DEVICE_NAME_GET, SD_BLE_GAP_AUTHENTICATE, SD_BLE_GAP_SEC_PARAMS_REPLY, SD_BLE_GAP_AUTH_KEY_REPLY, SD_BLE_GAP_SEC_INFO_REPLY, SD_BLE_GAP_CONN_SEC_GET, SD_BLE_GAP_RSSI_START, SD_BLE_GAP_RSSI_STOP }
	GAP API SVC numbers. More...

enum	BLE_GAP_EVTS { BLE_GAP_EVT_CONNECTED = 0x10, BLE_GAP_EVT_DISCONNECTED, BLE_GAP_EVT_CONN_PARAM_UPDATE, BLE_GAP_EVT_SEC_PARAMS_REQUEST, BLE_GAP_EVT_SEC_INFO_REQUEST, BLE_GAP_EVT_PASSKEY_DISPLAY, BLE_GAP_EVT_AUTH_KEY_REQUEST, BLE_GAP_EVT_AUTH_STATUS, BLE_GAP_EVT_CONN_SEC_UPDATE, BLE_GAP_EVT_TIMEOUT, BLE_GAP_EVT_RSSI_CHANGED }
	GAP Event IDs. Those IDs uniquely identify an event coming from the stack to the application. More...

Functions
uint32_t	sd_ble_gap_address_set (ble_gap_addr_t const *const p_addr)
	Set local Bluetooth address. More...

uint32_t	sd_ble_gap_address_get (ble_gap_addr_t *const p_addr)
	Get local Bluetooth address. More...

uint32_t	sd_ble_gap_adv_data_set (uint8_t const const p_data, uint8_t dlen, uint8_t const const p_sr_data, uint8_t srdlen)
	Set, clear or update advertisement and scan response data. More...

uint32_t	sd_ble_gap_adv_start (ble_gap_adv_params_t const *const p_adv_params)
	Start advertising (GAP Discoverable, Connectable modes, Broadcast Procedure). More...

uint32_t	sd_ble_gap_adv_stop (void)
	Stop advertising (GAP Discoverable, Connectable modes, Broadcast Procedure). More...

uint32_t	sd_ble_gap_conn_param_update (uint16_t conn_handle, ble_gap_conn_params_t const *const p_conn_params)
	Update connection parameters. More...

uint32_t	sd_ble_gap_disconnect (uint16_t conn_handle, uint8_t hci_status_code)
	Disconnect (GAP Link Termination). More...

uint32_t	sd_ble_gap_tx_power_set (int8_t tx_power)
	Set the radio's transmit power. More...

uint32_t	sd_ble_gap_appearance_set (uint16_t appearance)
	Set GAP Appearance value. More...

uint32_t	sd_ble_gap_appearance_get (uint16_t *const p_appearance)
	Get GAP Appearance value. More...

uint32_t	sd_ble_gap_ppcp_set (ble_gap_conn_params_t const *const p_conn_params)
	Set GAP Peripheral Preferred Connection Parameters. More...

uint32_t	sd_ble_gap_ppcp_get (ble_gap_conn_params_t *const p_conn_params)
	Get GAP Peripheral Preferred Connection Parameters. More...

uint32_t	sd_ble_gap_device_name_set (ble_gap_conn_sec_mode_t const const p_write_perm, uint8_t const const p_dev_name, uint16_t len)
	Set GAP device name. More...

uint32_t	sd_ble_gap_device_name_get (uint8_t const p_dev_name, uint16_t const p_len)
	Get GAP device name. More...

uint32_t	sd_ble_gap_authenticate (uint16_t conn_handle, ble_gap_sec_params_t const *const p_sec_params)
	Initiate GAP Authentication procedure. More...

uint32_t	sd_ble_gap_sec_params_reply (uint16_t conn_handle, uint8_t sec_status, ble_gap_sec_params_t const *const p_sec_params)
	Reply with GAP security parameters. More...

uint32_t	sd_ble_gap_auth_key_reply (uint16_t conn_handle, uint8_t key_type, uint8_t const *const key)
	Reply with an authentication key. More...

uint32_t	sd_ble_gap_sec_info_reply (uint16_t conn_handle, ble_gap_enc_info_t const const p_enc_info, ble_gap_sign_info_t const const p_sign_info)
	Reply with GAP security information. More...

uint32_t	sd_ble_gap_conn_sec_get (uint16_t conn_handle, ble_gap_conn_sec_t *const p_conn_sec)
	Get the current connection security. More...

uint32_t	sd_ble_gap_rssi_start (uint16_t conn_handle)
	Start reporting the received signal strength to the application. More...

uint32_t	sd_ble_gap_rssi_stop (uint16_t conn_handle)
	Stop reporting the received singnal strength. More...

Detailed Description

Definitions and prototypes for the GAP interface.

Enumeration Type Documentation

enum BLE_GAP_EVTS

GAP Event IDs. Those IDs uniquely identify an event coming from the stack to the application.

Enumerator
BLE_GAP_EVT_CONNECTED	Connection established.
BLE_GAP_EVT_DISCONNECTED	Disconnected from peer.
BLE_GAP_EVT_CONN_PARAM_UPDATE	Connection Parameters updated.
BLE_GAP_EVT_SEC_PARAMS_REQUEST	Request to provide security parameters.
BLE_GAP_EVT_SEC_INFO_REQUEST	Request to provide security information.
BLE_GAP_EVT_PASSKEY_DISPLAY	Request to display a passkey to the user.
BLE_GAP_EVT_AUTH_KEY_REQUEST	Request to provide an authentication key.
BLE_GAP_EVT_AUTH_STATUS	Authentication procedure completed with status.
BLE_GAP_EVT_CONN_SEC_UPDATE	Connection security updated.
BLE_GAP_EVT_TIMEOUT	Timeout expired.
BLE_GAP_EVT_RSSI_CHANGED	Signal strength measurement report.

enum BLE_GAP_SVCS

GAP API SVC numbers.

Enumerator
SD_BLE_GAP_ADDRESS_SET	Set own Bluetooth Address.
SD_BLE_GAP_ADDRESS_GET	Get own Bluetooth Address.
SD_BLE_GAP_ADV_DATA_SET	Set Advertisement Data.
SD_BLE_GAP_ADV_START	Start Advertising.
SD_BLE_GAP_ADV_STOP	Stop Advertising.
SD_BLE_GAP_CONN_PARAM_UPDATE	Connection Parameter Update.
SD_BLE_GAP_DISCONNECT	Disconnect.
SD_BLE_GAP_TX_POWER_SET	Set TX Power.
SD_BLE_GAP_APPEARANCE_SET	Set Appearance.
SD_BLE_GAP_APPEARANCE_GET	Get Appearance.
SD_BLE_GAP_PPCP_SET	Set PPCP.
SD_BLE_GAP_PPCP_GET	Get PPCP.
SD_BLE_GAP_DEVICE_NAME_SET	Set Device Name.
SD_BLE_GAP_DEVICE_NAME_GET	Get Device Name.
SD_BLE_GAP_AUTHENTICATE	Initiate Pairing/Bonding.
SD_BLE_GAP_SEC_PARAMS_REPLY	Reply with Security Parameters.
SD_BLE_GAP_AUTH_KEY_REPLY	Reply with an authentication key.
SD_BLE_GAP_SEC_INFO_REPLY	Reply with Security Information.
SD_BLE_GAP_CONN_SEC_GET	Obtain connection security level.
SD_BLE_GAP_RSSI_START	Start reporting of changes in RSSI.
SD_BLE_GAP_RSSI_STOP	Stop reporting of changes in RSSI.

Function Documentation

uint32_t sd_ble_gap_address_get ( ble_gap_addr_t *const p_addr )

Get local Bluetooth address.

Parameters

[out] p_addr Pointer to address structure.

Returns: NRF_SUCCESS Address successfully retrieved.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.

uint32_t sd_ble_gap_address_set ( ble_gap_addr_t const *const p_addr )

Set local Bluetooth address.

Parameters

[in] p_addr Pointer to address structure.

Returns: NRF_SUCCESS Address successfully set.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; BLE_ERROR_GAP_INVALID_BLE_ADDR Invalid address.; NRF_ERROR_BUSY The stack is busy, process pending events and retry.

uint32_t sd_ble_gap_adv_data_set	(	uint8_t const *const	p_data,
		uint8_t	dlen,
		uint8_t const *const	p_sr_data,
		uint8_t	srdlen
	)

Set, clear or update advertisement and scan response data.

Note: The format of the advertisement data will be checked by this call to ensure interoperability. Limitations imposed by this API call to the data provided include having a flags data type in the scan response data and duplicating the local name in the advertisement data and scan response data.; : To clear the advertisement data and set it to a 0-length packet, simply provide a valid pointer (p_data/p_sr_data) with its corresponding length (dlen/srdlen) set to 0.; : The call will fail if p_data and p_sr_data are both NULL since this would have no effect.

Parameters

[in]	p_data	Raw data to be placed in advertisement packet. If NULL, no changes are made to the current advertisement packet data.
[in]	dlen	Data length for p_data. Max size: BLE_GAP_ADV_MAX_SIZE octets. Should be 0 if p_data is NULL, can be 0 if p_data is not NULL.
[in]	p_sr_data	Raw data to be placed in scan response packet. If NULL, no changes are made to the current scan response packet data.
[in]	srdlen	Data length for p_sr_data. Max size: BLE_GAP_ADV_MAX_SIZE octets. Should be 0 if p_sr_data is NULL, can be 0 if p_data is not NULL.

Returns: NRF_SUCCESS Advertisement data successfully updated or cleared.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_FLAGS Invalid combination of advertising flags supplied.; NRF_ERROR_INVALID_DATA Invalid data type(s) supplied, check the advertising data format specification.; NRF_ERROR_INVALID_LENGTH Invalid data length(s) supplied.; BLE_ERROR_GAP_UUID_LIST_MISMATCH Invalid UUID list supplied.; NRF_ERROR_BUSY The stack is busy, process pending events and retry.

uint32_t sd_ble_gap_adv_start ( ble_gap_adv_params_t const *const p_adv_params )

Start advertising (GAP Discoverable, Connectable modes, Broadcast Procedure).

Parameters

[in] p_adv_params Pointer to advertising parameters structure.

Returns: NRF_SUCCESS The BLE stack has started advertising.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_STATE Invalid state to perform operation.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied, check the accepted ranges and limits.; BLE_ERROR_GAP_INVALID_BLE_ADDR Invalid Bluetooth address supplied.; BLE_ERROR_GAP_DISCOVERABLE_WITH_WHITELIST Discoverable mode and whitelist incompatible.

uint32_t sd_ble_gap_adv_stop ( void )

Stop advertising (GAP Discoverable, Connectable modes, Broadcast Procedure).

Returns: NRF_SUCCESS The BLE stack has stopped advertising.; NRF_ERROR_INVALID_STATE Invalid state to perform operation (most probably not in advertising state).

uint32_t sd_ble_gap_appearance_get ( uint16_t *const p_appearance )

Get GAP Appearance value.

Parameters

[out] p_appearance Appearance (16-bit), see BLE_APPEARANCES.

Returns: NRF_SUCCESS Appearance value retrieved successfully.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.

uint32_t sd_ble_gap_appearance_set ( uint16_t appearance )

Set GAP Appearance value.

Parameters

[in] appearance Appearance (16-bit), see BLE_APPEARANCES.

Returns: NRF_SUCCESS Appearance value set successfully.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.

uint32_t sd_ble_gap_auth_key_reply	(	uint16_t	conn_handle,
		uint8_t	key_type,
		uint8_t const *const	key
	)

Reply with an authentication key.

Parameters

[in]	conn_handle	Connection handle.
[in]	key_type	See BLE_GAP_AUTH_KEY_TYPES.
[in]	key	If key type is BLE_GAP_AUTH_KEY_TYPE_NONE, then NULL. If key type is BLE_GAP_AUTH_KEY_TYPE_PASSKEY, then a 6-byte ASCII string (digit 0..9 only, no NULL termination). If key type is BLE_GAP_AUTH_KEY_TYPE_OOB, then a 16-byte OOB key value in Little Endian format.

This function is only used to reply to a BLE_GAP_EVT_AUTH_KEY_REQUEST, calling it at other times will result in an NRF_ERROR_INVALID_STATE.

Note: If the call returns an error code, the request is still pending, and the reply call may be repeated with corrected parameters.

Returns: NRF_SUCCESS Authentication key successfully set.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.; NRF_ERROR_INVALID_STATE Invalid state to perform operation.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.

uint32_t sd_ble_gap_authenticate	(	uint16_t	conn_handle,
		ble_gap_sec_params_t const *const	p_sec_params
	)

Initiate GAP Authentication procedure.

Parameters

[in]	conn_handle	Connection handle.
[in]	p_sec_params	Pointer to the ble_gap_sec_params_t structure with the security parameters to be used during the pairing procedure.

In the central role, this function will send an SMP Pairing Request, otherwise in the peripheral role, an SMP Security Request will be sent. In the peripheral role, only the timeout, bond and mitm fields of ble_gap_sec_params_t are used.

Note: The GAP Authentication procedure may be triggered by the central without calling this function when accessing a secure service.; Calling this function may result in the following events depending on the outcome and parameters: BLE_GAP_EVT_SEC_PARAMS_REQUEST, BLE_GAP_EVT_SEC_INFO_REQUEST, BLE_GAP_EVT_AUTH_KEY_REQUEST, BLE_GAP_EVT_AUTH_STATUS.; The timeout parameter in ble_gap_sec_params_t is interpreted here as the Security Request timeout

Returns: NRF_SUCCESS Successfully initiated authentication procedure.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.; NRF_ERROR_INVALID_STATE Invalid state to perform operation.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.

uint32_t sd_ble_gap_conn_param_update	(	uint16_t	conn_handle,
		ble_gap_conn_params_t const *const	p_conn_params
	)

Update connection parameters.

In the central role this will initiate a Link Layer connection parameter update procedure, otherwise in the peripheral role, this will send the corresponding L2CAP request and wait for the central to perform the procedure. In both cases, and regardless of success or failure, the application will be informed of the result with a BLE_GAP_EVT_CONN_PARAM_UPDATE event.

Note: If both a connection supervision timeout and a maximum connection interval are specified, then the following constraint applies: (conn_sup_timeout * 8) >= (max_conn_interval * (slave_latency + 1))

Parameters

[in]	conn_handle	Connection handle.
[in]	p_conn_params	Pointer to desired connection parameters. If NULL is provided on a peripheral role, the parameters in the PPCP characteristic of the GAP service will be used instead.

Returns: NRF_SUCCESS The Connection Update procedure has been started successfully.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied, check parameter limits and constraints.; NRF_ERROR_BUSY Procedure already in progress or not allowed at this time, process pending events and retry.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.; NRF_ERROR_NO_MEM Not enough memory to complete operation.

uint32_t sd_ble_gap_conn_sec_get	(	uint16_t	conn_handle,
		ble_gap_conn_sec_t *const	p_conn_sec
	)

Get the current connection security.

Parameters

[in]	conn_handle	Connection handle.
[out]	p_conn_sec	Pointer to a ble_gap_conn_sec_t structure to be filled in.

Returns: NRF_SUCCESS Current connection security successfully retrieved.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.

uint32_t sd_ble_gap_device_name_get	(	uint8_t *const	p_dev_name,
		uint16_t *const	p_len
	)

Get GAP device name.

Parameters

[in]	p_dev_name	Pointer to an empty buffer where the UTF-8 non NULL-terminated string will be placed. Set to NULL to obtain the complete device name length.
[in,out]	p_len	Length of the buffer pointed by p_dev_name, complete device name length on output.

Note: If the device name is longer than the size of the supplied buffer, p_len will return the complete device name length, and not the number of bytes actually returned in p_dev_name. The application may use this information to allocate a suitable buffer size.

Returns: NRF_SUCCESS GAP device name retrieved successfully.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_DATA_SIZE Invalid data size(s) supplied.

uint32_t sd_ble_gap_device_name_set	(	ble_gap_conn_sec_mode_t const *const	p_write_perm,
		uint8_t const *const	p_dev_name,
		uint16_t	len
	)

Set GAP device name.

Parameters

[in]	p_write_perm	Write permissions for the Device Name characteristic see ble_gap_conn_sec_mode_t.
[in]	p_dev_name	Pointer to a UTF-8 encoded, non NULL-terminated string.
[in]	len	Length of the UTF-8, non NULL-terminated string pointed to by p_dev_name in octets (must be smaller or equal than BLE_GAP_DEVNAME_MAX_LEN).

Returns: NRF_SUCCESS GAP device name and permissions set successfully.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.; NRF_ERROR_DATA_SIZE Invalid data size(s) supplied.

uint32_t sd_ble_gap_disconnect	(	uint16_t	conn_handle,
		uint8_t	hci_status_code
	)

Disconnect (GAP Link Termination).

This call initiates the disconnection procedure, and its completion will be communicated to the application with a BLE_GAP_EVT_DISCONNECTED event.

Parameters

[in]	conn_handle	Connection handle.
[in]	hci_status_code	HCI status code, see BLE_HCI_STATUS_CODES (accepted values are BTLE_REMOTE_USER_TERMINATED_CONNECTION and BTLE_CONN_INTERVAL_UNACCEPTABLE).

Returns: NRF_SUCCESS The disconnection procedure has been started successfully.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.; NRF_ERROR_INVALID_STATE Invalid state to perform operation (disconnection is already in progress or not connected at all).

uint32_t sd_ble_gap_ppcp_get ( ble_gap_conn_params_t *const p_conn_params )

Get GAP Peripheral Preferred Connection Parameters.

Parameters

[out] p_conn_params Pointer to a ble_gap_conn_params_t structure where the parameters will be stored.

Returns: NRF_SUCCESS Peripheral Preferred Connection Parameters retrieved successfully.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.

uint32_t sd_ble_gap_ppcp_set ( ble_gap_conn_params_t const *const p_conn_params )

Set GAP Peripheral Preferred Connection Parameters.

Parameters

[in] p_conn_params Pointer to a ble_gap_conn_params_t structure with the desired parameters.

Returns: NRF_SUCCESS Peripheral Preferred Connection Parameters set successfully.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.

uint32_t sd_ble_gap_rssi_start ( uint16_t conn_handle )

Start reporting the received signal strength to the application.

A new event is reported whenever the RSSI value changes, until sd_ble_gap_rssi_stop is called.

Parameters

[in] conn_handle Connection handle.

Returns: NRF_SUCCESS Successfully activated RSSI reporting.; NRF_ERROR_INVALID_STATE Invalid state to perform operation.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.

uint32_t sd_ble_gap_rssi_stop ( uint16_t conn_handle )

Stop reporting the received singnal strength.

An RSSI change detected before the call but not yet received by the application may be reported after sd_ble_gap_rssi_stop has been called.

Parameters

[in] conn_handle Connection handle.

Returns: NRF_SUCCESS Successfully deactivated RSSI reporting.; NRF_ERROR_INVALID_STATE Invalid state to perform operation.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.

uint32_t sd_ble_gap_sec_info_reply	(	uint16_t	conn_handle,
		ble_gap_enc_info_t const *const	p_enc_info,
		ble_gap_sign_info_t const *const	p_sign_info
	)

Reply with GAP security information.

Parameters

[in]	conn_handle	Connection handle.
[in]	p_enc_info	Pointer to a ble_gap_enc_info_t encryption information structure. May be NULL to signal none is available.
[in]	p_sign_info	Pointer to a ble_gap_sign_info_t signing information structure. May be NULL to signal none is available.

This function is only used to reply to a BLE_GAP_EVT_SEC_INFO_REQUEST, calling it at other times will result in NRF_ERROR_INVALID_STATE.

Note: If the call returns an error code, the request is still pending, and the reply call may be repeated with corrected parameters.; Data signing is not implemented yet. p_sign_info must therefore be NULL.

Returns: NRF_SUCCESS Successfully accepted security information.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.; NRF_ERROR_INVALID_STATE Invalid state to perform operation.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.; NRF_ERROR_BUSY The stack is busy, process pending events and retry.

uint32_t sd_ble_gap_sec_params_reply	(	uint16_t	conn_handle,
		uint8_t	sec_status,
		ble_gap_sec_params_t const *const	p_sec_params
	)

Reply with GAP security parameters.

Parameters

[in]	conn_handle	Connection handle.
[in]	sec_status	Security status, see BLE_GAP_SEC_STATUS.
[in]	p_sec_params	Pointer to a ble_gap_sec_params_t security parameters structure.

This function is only used to reply to a BLE_GAP_EVT_SEC_PARAMS_REQUEST, calling it at other times will result in an NRF_ERROR_INVALID_STATE.

Note: If the call returns an error code, the request is still pending, and the reply call may be repeated with corrected parameters.; The timeout parameter in ble_gap_sec_params_t is interpreted here as the SMP procedure timeout, and must be 30 seconds. The function will fail if the application supplies a different value.

Returns: NRF_SUCCESS Successfully accepted security parameter from the application.; NRF_ERROR_INVALID_ADDR Invalid pointer supplied.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.; NRF_ERROR_INVALID_STATE Invalid state to perform operation.; BLE_ERROR_INVALID_CONN_HANDLE Invalid connection handle supplied.

uint32_t sd_ble_gap_tx_power_set ( int8_t tx_power )

Set the radio's transmit power.

Parameters

[in] tx_power Radio transmit power in dBm (accepted values are -40, -30, -20, -16, -12, -8, -4, 0, and 4 dBm).

Note: -40 dBm will not actually give -40 dBm, but will instead be remapped to -30 dBm.

Returns: NRF_SUCCESS Successfully changed the transmit power.; NRF_ERROR_INVALID_PARAM Invalid parameter(s) supplied.; NRF_ERROR_BUSY The stack is busy, process pending events and retry.

Modules

Data Structures

Enumerations

Functions

Detailed Description

Enumeration Type Documentation

Function Documentation