Module for testing RF/PHY using DTM commands. More...

Macros
#define	DEFAULT_TX_POWER RADIO_TXPOWER_TXPOWER_Pos4dBm
	Configuration parameters. More...

#define	DEFAULT_TIMER NRF_TIMER0

#define	DEFAULT_TIMER_IRQn TIMER0_IRQn

#define	LE_RESET 0

#define	LE_RECEIVER_TEST 1

#define	LE_TRANSMITTER_TEST 2

#define	LE_TEST_END 3

#define	CARRIER_TEST 0

#define	CARRIER_TEST_STUDIO 1

#define	SET_TX_POWER 2

#define	SELECT_TIMER 3

#define	LE_PACKET_REPORTING_EVENT 0x8000

#define	LE_TEST_STATUS_EVENT_SUCCESS 0x0000

#define	LE_TEST_STATUS_EVENT_ERROR 0x0001

#define	DTM_PKT_PRBS9 0x00

#define	DTM_PKT_0X0F 0x01

#define	DTM_PKT_0X55 0x02

#define	DTM_PKT_VENDORSPECIFIC 0xFFFFFFFF

#define	DTM_SUCCESS 0x00
	Return codes from dtm_cmd(). More...

#define	DTM_ERROR_ILLEGAL_CHANNEL 0x01

#define	DTM_ERROR_INVALID_STATE 0x02

#define	DTM_ERROR_ILLEGAL_LENGTH 0x03

#define	DTM_ERROR_ILLEGAL_CONFIGURATION 0x04

#define	DTM_ERROR_UNINITIALIZED 0x05

#define	PACKET_TYPE_MAX DTM_PKT_0X55

Typedefs
typedef uint32_t	dtm_cmd_t
	BLE DTM command codes. More...

typedef uint32_t	dtm_event_t
	BLE DTM event type. More...

typedef uint32_t	dtm_freq_t
	BLE DTM frequency type. More...

typedef uint32_t	dtm_pkt_type_t
	BLE DTM packet types. More...

Functions
uint32_t	dtm_init (void)
	Function for initializing or re-initializing DTM module. More...

uint32_t	dtm_wait (void)
	Function for giving control to dtmlib for handling timer and radio events. Will return to caller at 625us intervals or whenever another event than radio occurs (such as UART input). Function will put MCU to sleep between events. More...

uint32_t	dtm_cmd (dtm_cmd_t cmd, dtm_freq_t freq, uint32_t length, dtm_pkt_type_t payload)
	Function for calling when a complete command has been prepared by the Tester. More...

bool	dtm_event_get (dtm_event_t *p_dtm_event)
	Function for reading the result of a DTM command. More...

bool	dtm_set_timer (uint32_t new_timer)
	Function for configuring the timer to use. More...

bool	dtm_set_txpower (uint32_t new_tx_power)
	Function for configuring the transmit power. More...

Detailed Description

Module for testing RF/PHY using DTM commands.

Macro Definition Documentation

#define CARRIER_TEST 0

Length=0 indicates a constant, unmodulated carrier until LE_TEST_END or LE_RESET

#define CARRIER_TEST_STUDIO 1

nRFgo Studio uses value 1 in length field, to indicate a constant, unmodulated carrier until LE_TEST_END or LE_RESET

#define DEFAULT_TIMER NRF_TIMER0

Default timer used for timing.

#define DEFAULT_TIMER_IRQn TIMER0_IRQn

IRQ used for timer. NOTE: MUST correspond to DEFAULT_TIMER.

#define DEFAULT_TX_POWER RADIO_TXPOWER_TXPOWER_Pos4dBm

Configuration parameters.

Default Transmission power using in the DTM module.

#define DTM_ERROR_ILLEGAL_CHANNEL 0x01

Physical channel number must be in the range 0..39.

#define DTM_ERROR_ILLEGAL_CONFIGURATION 0x04

Parameter out of range (legal range is function dependent).

#define DTM_ERROR_ILLEGAL_LENGTH 0x03

Payload size must be in the range 0..37.

#define DTM_ERROR_INVALID_STATE 0x02

Sequencing error: Command is not valid now.

#define DTM_ERROR_UNINITIALIZED 0x05

DTM module has not been initialized by the application.

#define DTM_PKT_0X0F 0x01

Bit pattern 11110000 (LSB is the leftmost bit).

#define DTM_PKT_0X55 0x02

Bit pattern 10101010 (LSB is the leftmost bit).

#define DTM_PKT_PRBS9 0x00

Bit pattern PRBS9.

#define DTM_PKT_VENDORSPECIFIC 0xFFFFFFFF

Vendor specific. Nordic: Continuous carrier test, or configuration.

#define DTM_SUCCESS 0x00

Return codes from dtm_cmd().

Indicate that the DTM function completed with success.

#define LE_PACKET_REPORTING_EVENT 0x8000

DTM Packet reporting event, returned by the device to the tester.

#define LE_RECEIVER_TEST 1

DTM command: Start receive test.

#define LE_RESET 0

DTM command: Reset device.

#define LE_TEST_END 3

DTM command: End test and send packet report.

#define LE_TEST_STATUS_EVENT_ERROR 0x0001

DTM Status event, indicating an error.

#define LE_TEST_STATUS_EVENT_SUCCESS 0x0000

DTM Status event, indicating success.

#define LE_TRANSMITTER_TEST 2

DTM command: Start transmission test.

#define PACKET_TYPE_MAX DTM_PKT_0X55

Highest value allowed as DTM Packet type.

#define SELECT_TIMER 3

Select on of the 16 MHz timers 0, 1 or 2

#define SET_TX_POWER 2

Set transmission power, value -40..+4 dBm in steps of 4

Typedef Documentation

typedef uint32_t dtm_cmd_t

BLE DTM command codes.

DTM command type.

typedef uint32_t dtm_event_t

BLE DTM event type.

Type for handling DTM event.

typedef uint32_t dtm_freq_t

BLE DTM frequency type.

Physical channel, valid range: 0..39.

typedef uint32_t dtm_pkt_type_t

BLE DTM packet types.

Type for holding the requested DTM payload type.

Function Documentation

uint32_t dtm_cmd	(	dtm_cmd_t	cmd,
		dtm_freq_t	freq,
		uint32_t	length,
		dtm_pkt_type_t	payload
	)

Function for calling when a complete command has been prepared by the Tester.

Parameters

[in]	cmd	One of the DTM_CMD values (bits 14:15 in the 16-bit UART format).
[in]	freq	Phys. channel no - actual frequency = (2402 + freq * 2) MHz (bits 8:13 in the 16-bit UART format).
[in]	length	Payload length, 0..37 (bits 2:7 in the 16-bit UART format).
[in]	payload	One of the DTM_PKT values (bits 0:1 in the 16-bit UART format).

Returns: DTM_SUCCESS or one of the DTM_ERROR_ values

bool dtm_event_get ( dtm_event_t * p_dtm_event )

Function for reading the result of a DTM command.

Parameters

[out] p_dtm_event Pointer to buffer for 16 bit event code according to DTM standard.

Returns: true: new event, false: no event since last call, this event has been read earlier

uint32_t dtm_init ( void )

Function for initializing or re-initializing DTM module.

Returns: DTM_SUCCESS on successful initialization of the DTM module.

bool dtm_set_timer ( uint32_t new_timer )

Function for configuring the timer to use.

Note: Must be called when no DTM test is running.

Parameters

[in] new_timer Index (0..2) of timer to be used by the DTM library

Returns: true: success, new timer was selected, false: parameter error

bool dtm_set_txpower ( uint32_t new_tx_power )

Function for configuring the transmit power.

Note: Must be called when no DTM test is running.

Parameters

[in] new_tx_power New output level, +4..-40, in steps of 4.

Returns: true: tx power setting changed, false: parameter error

uint32_t dtm_wait ( void )

Function for giving control to dtmlib for handling timer and radio events. Will return to caller at 625us intervals or whenever another event than radio occurs (such as UART input). Function will put MCU to sleep between events.

Returns: Time counter, incremented every 625 us.

Macros

Typedefs

Functions

Detailed Description

Macro Definition Documentation

Typedef Documentation

Function Documentation