BLE S110 Functions

Table of Contents

• 0x34 - sd_power_system_off
  • Function packet format.
  • Response packet format
• 0x52 - sd_temp_get
  • Function packet format.
  • Response packet format
• 0x60 - sd_ble_enable
  • Function packet format
  • Response packet format
• 0x62 - sd_ble_tx_buffer_count_get
  • Function packet format
  • Response packet format
• 0x63 - sd_ble_uuid_vs_add
  • Function packet format
  • Response packet format
• 0x64 - sd_ble_uuid_decode
  • Function packet format
  • Response packet format
• 0x65 - sd_ble_uuid_encode
  • Function packet format
  • Response packet format
• 0x66 - sd_ble_version_get
  • Function packet format
  • Response packet format
• 0x67 - sd_ble_user_mem_reply
  • Function packet format
  • Response packet format
• 0x68 - sd_ble_opt_set
  • Function packet format
  • Encoding of BLE Option
  • Response packet format
• 0x69 - sd_ble_opt_get
  • Function packet format
  • Response packet format

0x34 - sd_power_system_off

Function packet format.

Frame format encoding of the sd_power_system_off packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x34

Figure 1: Packet format for sd_system_power_off function.

Response packet format

There is no response for this command.

0x52 - sd_temp_get

Function packet format.

Frame format encoding of the sd_temp_get packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x52
1 byte	Temperature Present	0x00 - not present, 0x01 - present

Figure 1: Packet format for sd_temp_get function.

Response packet format

Frame format encoding of the sd_temp_get response packet:

Length	Parameter	Value
1 byte	Operation Code	0x52
4 bytes	nRF Error Code	See sd_temp_get
4 bytes	Measured Temperature Value	See sd_temp_get

Figure 2: Packet format for sd_temp_get response.

0x60 - sd_ble_enable

Function packet format

Frame format encoding of the sd_ble_enable packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x60, see BLE_COMMON_SVCS
1 byte	Enable Params Present	0x00 - not present, 0x01 - present
5 bytes	Conditional: Enable Params	See ble_enable_params_t

Figure 1: Packet format for sd_ble_enable function.

Response packet format

Frame format encoding of the sd_ble_enable response packet:

Length	Parameter	Value
1 byte	Operation Code	0x60, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_enable

Figure 2: Packet format for sd_ble_enabale response.

0x62 - sd_ble_tx_buffer_count_get

Function packet format

Frame format encoding of the sd_ble_tx_buffer_count_get packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x62, see BLE_COMMON_SVCS
1 byte	Tx Buffer Count Present	0x00 - not present, 0x01 - present

Figure 1: Packet format for sd_ble_tx_buffer_count_get function.

Response packet format

If a command was executed successfully, so that 'nRF Error Code' = NRF_SUCCESS, the nRF Error Code is followed by conditional data.

Frame format encoding of the sd_ble_tx_buffer_count_get response packet:

Length	Parameter	Value
1 byte	Operation Code	0x62, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_tx_buffer_count_get
1 byte	Conditional: Tx Buffer Count Present	0x00 - not present, 0x01 - present
1 byte	Conditional: Tx Buffer Count	See sd_ble_tx_buffer_count_get

Figure 2: Packet format for sd_ble_tx_buffer_count_get function response.

0x63 - sd_ble_uuid_vs_add

Function packet format

Frame format encoding of the sd_ble_uuid_vs_add packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x63, see BLE_COMMON_SVCS
1 byte	UUID Present	0x00 - not present, 0x01 - present
16 bytes	Conditional: Vendor Specific UUID	See ble_uuid128_t
1 byte	UUID type Present	0x00 - not present, 0x01 - present

Figure 1: Packet format for sd_ble_uuid_vs_add function.

Response packet format

If a command was executed successfully, so that 'nRF Error Code' = NRF_SUCCESS, the nRF Error Code is followed by conditional data.

Frame format encoding of the sd_ble_uuid_vs_add response packet:

Length	Parameter	Value
1 byte	Operation Code	0x63, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_uuid_vs_add
1 byte	UUID Type Present	0x00 - not present, 0x01 - present
1 byte	Conditional: UUID Type	Index to Vendor Specific UUID

Figure 2: Packet format for sd_ble_uuid_vs_add response.

0x64 - sd_ble_uuid_decode

Function packet format

Frame format encoding of the sd_ble_uuid_decode packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x64, see BLE_COMMON_SVCS
1 byte	Length of Raw UUID	Shall be 2 or 16 bytes
1 byte	Raw UUID Present	0x00 - not present, 0x01 - present
2 or 16 bytes	Raw UUID	Raw UUID to be decoded
1 byte	UUID Result Struct Present	0x00 - not present, 0x01 - present

Figure 1: Packet format for sd_ble_uuid_decode request function.

Response packet format

If a command was executed successfully, so that 'nRF Error Code' = NRF_SUCCESS, the nRF Error Code is followed by conditional data.

Frame format encoding of the sd_ble_uuid_decode response packet:

Length	Parameter	Value
1 byte	Operation Code	0x64, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_uuid_decode
1 byte	Conditional: ble_uuid_t Present	0x00 - not present, 0x01 - present
3 bytes	Conditional: Encoded UUID	Raw UUID decoded to ble_uuid_t

ble_uuid_t is encoded in the following order:

Length	Parameter	Value
2 bytes	UUID	UUID Value
1 byte	Type	UUID Type

Figure 2: Packet format for sd_ble_uuid_decode response.

0x65 - sd_ble_uuid_encode

Function packet format

Frame format encoding of the sd_ble_uuid_encode packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x65, see BLE_COMMON_SVCS
1 byte	UUID Present	0x00 - not present, 0x01 - present
3 bytes	Conditional: UUID	See ble_uuid_t
1 byte	Length Present	0x00 - not present, 0x01 - present
1 byte	UUID Result Buffer Present	0x00 - not present, 0x01 - present

As can also be seen inside Figure 1, the 3 bytes inside ble_uuid_t are encoded as:

Length	Parameter	Value
2 bytes	UUID	UUID Value
1 byte	Type	UUID Type

Figure 1: Packet format for sd_ble_uuid_encode function.

Response packet format

If a command was executed successfully, so that 'nRF Error Code' = NRF_SUCCESS, the nRF Error Code is followed by conditional data.

Frame format encoding of the sd_ble_uuid_encode response packet:

Length	Parameter	Value
1 byte	Operation Code	0x65, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_uuid_encode
1 byte	Conditional: Length of encoded UUID	2 or 16
2 or 16 bytes	Conditional: Encoded UUID	UUID value

Figure 2: Packet format for sd_ble_uuid_encode response.

0x66 - sd_ble_version_get

Function packet format

Frame format encoding of the sd_ble_version_get packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x66, see BLE_COMMON_SVCS
1 byte	Version Present	0x00 - not present, 0x01 - present

Figure 1: Packet format for sd_ble_version_get function.

Response packet format

If a command was executed successfully, so that 'nRF Error Code' = NRF_SUCCESS, the nRF Error Code is followed by conditional data.

Frame format encoding of the sd_ble_version_get response packet:

Length	Parameter	Value
1 byte	Operation Code	0x66, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_version_get
1 byte	Conditional: Version Number	See ble_version_t::version_number
2 bytes	Conditional: Company ID	See ble_version_t::company_id
2 bytes	Conditional: Subversion Number	See ble_version_t::subversion_number

Figure 2: Packet format for sd_ble_version_get response.

0x67 - sd_ble_user_mem_reply

Function packet format

Frame format encoding of the sd_ble_user_mem_reply packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x67, see BLE_COMMON_SVCS
2 bytes	Connection Handle	Handle value
1 byte	Memory Block Structure Present	0x00 - not present, 0x01 - present
2 bytes	Conditional: Length	Length of memory block, see ble_user_mem_block_t::len
1 byte	Conditional: Memory Block Present	0x00 - not present, 0x01 - present

Figure 1: Packet format for sd_ble_user_mem_reply function.

Note

When sd_ble_user_mem_reply is called, a user memory context is created using app_ble_user_mem_context_create and conn_ble_user_mem_context_create. This context corresponds to a single connection indicated by the connection handle. The context is used to synchronize the user memory block between Connectivity and Application processor. It is released using app_ble_user_mem_context_destroy and conn_ble_user_mem_context_destroy when BLE_EVT_USER_MEM_RELEASE is received.

Response packet format

If a command was executed successfully, so that 'nRF Error Code' = NRF_SUCCESS, the nRF Error Code is followed by conditional data.

Frame format encoding of the sd_ble_user_mem_reply response packet:

Length	Parameter	Value
1 byte	Operation Code	0x67, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_user_mem_reply

Figure 2: Packet format for sd_ble_user_mem_reply response.

0x68 - sd_ble_opt_set

Function packet format

Frame format encoding of the sd_ble_opt_set packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x68, see BLE_COMMON_SVCS
4 bytes	Option ID	See sd_ble_opt_set
1 byte	Option present	0x00 - not present, 0x01 - present
1 ... 19 bytes	Conditional: Option	See ble_opt_t

Figure 1: Packet format for sd_ble_opt_set function.

Encoding of BLE Option

The Option field (if present) is encoded depending on the Option ID field.

If 'Option ID' equals BLE_GAP_OPT_CH_MAP, Option is encoded as follows:

Length	Parameter	Value
2 bytes	Connection Handle	See ble_gap_opt_ch_map_t::conn_handle
5 bytes	Channel Map	See ble_gap_opt_ch_map_t::ch_map[5]

Figure 2: Encoding of Option when Option ID equals BLE_GAP_OPT_CH_MAP.

If 'Option ID' equals BLE_GAP_OPT_LOCAL_CONN_LATENCY, Option is encoded as follows:

Length	Parameter	Value
2 bytes	Connection Handle	See ble_gap_opt_local_conn_latency_t
2 bytes	Requested Latency	See ble_gap_opt_local_conn_latency_t
1 byte	Actual Latency present	0x00 - not present, 0x01 - present
2 bytes	Conditional: Actual Latency	See ble_gap_opt_local_conn_latency_t

Figure 2: Encoding of Option when Option ID equals BLE_GAP_OPT_LOCAL_CONN_LATENCY.

If 'Option ID' = BLE_GAP_OPT_PASSKEY, Option is encoded as follows:

Length	Parameter	Value
6 bytes	Passkey	See ble_gap_opt_passkey_t

Figure 3: Encoding of Option when Option ID equals BLE_GAP_OPT_PASSKEY.

If 'Option ID' = BLE_GAP_OPT_PRIVACY, Option is encoded as follows:

Length	Parameter	Value
1 byte	IRK present	0x00 - not present, 0x01 - present
16 bytes	Conditional: IRK	See ble_gap_opt_privacy_t
2 bytes	Interval	See ble_gap_opt_privacy_t

Figure 4: Encoding of Option when Option ID equals BLE_GAP_OPT_PRIVACY.

If 'Option ID' = BLE_GAP_OPT_SCAN_REQ_REPORT, Option is encoded as follows:

Length	Parameter	Value
1 byte	Scan request report (bitfield): - enable: 1 bit	See ble_gap_opt_scan_req_report_t

If 'GAP Option ID' = BLE_GAP_OPT_COMPAT_MODE, Option is encoded as follows:

Length	Parameter	Value
1 byte	Compatibility mode (bitfield): - mode_1_enable: 1 bit	See ble_gap_opt_compat_mode_t

If 'Option ID' = BLE_COMMON_OPT_RADIO_CPU_MUTEX, Option is encoded as follows:

Length	Parameter	Value
1 byte	Radio CPU mutex (bitfield): - enable: 1 bit	See ble_common_opt_radio_cpu_mutex_t

Figure 5: Encoding of Option when Option ID equals BLE_GAP_OPT_SCAN_REQ_REPORT or BLE_GAP_OPT_COMPAT_MODE or BLE_COMMON_OPT_RADIO_CPU_MUTEX.

Response packet format

Frame encoding of the sd_ble_opt_set response packet:

Length	Parameter	Value
1 byte	Operation Code	0x68, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_opt_set

Figure 6: Packet format for sd_ble_opt_set response.

0x69 - sd_ble_opt_get

Function packet format

Frame format encoding of the sd_ble_opt_get packet.

The parameters are encoded in the following order:

Length	Parameter	Value
1 byte	Operation Code	0x69, see BLE_COMMON_SVCS
4 bytes	Option ID	See sd_ble_opt_get
1 byte	Option present	0x00 - not present, 0x01 - present

Figure 1: Packet format for sd_ble_opt_get function.

Response packet format

If a command was executed successfully, so that 'nRF Error Code' = NRF_SUCCESS, the nRF Error Code is followed by conditional data.

Frame encoding of the sd_ble_opt_get response packet:

Length	Parameter	Value
1 byte	Operation Code	0x69, see BLE_COMMON_SVCS
4 bytes	nRF Error Code	See sd_ble_opt_get
4 bytes	Conditional: Option ID	See sd_ble_opt_get
1 ... 19 bytes	Conditional: Option	See ble_opt_t

Figure 2: Packet format for sd_ble_opt_get response.

Encoding of the conditional field "Option" is done in the same way as in the sd_ble_opt_set request packet, which is described in detail in section Encoding of BLE Option.