GPIO pin abstraction and port abstraction for reading and writing byte-wise to GPIO ports. More...

Enumerations
enum	nrf_gpio_port_dir_t { NRF_GPIO_PORT_DIR_OUTPUT, NRF_GPIO_PORT_DIR_INPUT }
	Enumerator used for setting the direction of a GPIO port. More...

enum	nrf_gpio_pin_dir_t { NRF_GPIO_PIN_DIR_INPUT, NRF_GPIO_PIN_DIR_OUTPUT }

enum	nrf_gpio_port_select_t { NRF_GPIO_PORT_SELECT_PORT0 = 0, NRF_GPIO_PORT_SELECT_PORT1, NRF_GPIO_PORT_SELECT_PORT2, NRF_GPIO_PORT_SELECT_PORT3 }
	Enumerator used for selecting between port 0 - 3. More...

enum	nrf_gpio_pin_pull_t { NRF_GPIO_PIN_NOPULL = GPIO_PIN_CNF_PULL_Disabled, NRF_GPIO_PIN_PULLDOWN = GPIO_PIN_CNF_PULL_Pulldown, NRF_GPIO_PIN_PULLUP = GPIO_PIN_CNF_PULL_Pullup }
	Enumerator used for selecting the pin to be pulled down or up at the time of pin configuration. More...

enum	nrf_gpio_pin_sense_t { NRF_GPIO_PIN_NOSENSE = GPIO_PIN_CNF_SENSE_Disabled, NRF_GPIO_PIN_SENSE_LOW = GPIO_PIN_CNF_SENSE_Low, NRF_GPIO_PIN_SENSE_HIGH = GPIO_PIN_CNF_SENSE_High }
	Enumerator used for selecting the pin to sense high or low level on the pin input. More...

Functions
static __INLINE void	nrf_gpio_range_cfg_output (uint32_t pin_range_start, uint32_t pin_range_end)
	Function for configuring the GPIO pin range as outputs with normal drive strength. This function can be used to configure pin range as simple output with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases). More...

static __INLINE void	nrf_gpio_range_cfg_input (uint32_t pin_range_start, uint32_t pin_range_end, nrf_gpio_pin_pull_t pull_config)
	Function for configuring the GPIO pin range as inputs with given initial value set, hiding inner details. This function can be used to configure pin range as simple input. More...

static __INLINE void	nrf_gpio_cfg_output (uint32_t pin_number)
	Function for configuring the given GPIO pin number as output with given initial value set, hiding inner details. This function can be used to configure pin range as simple input with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases). More...

static __INLINE void	nrf_gpio_cfg_input (uint32_t pin_number, nrf_gpio_pin_pull_t pull_config)
	Function for configuring the given GPIO pin number as input with given initial value set, hiding inner details. This function can be used to configure pin range as simple input with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases). More...

static __INLINE void	nrf_gpio_cfg_sense_input (uint32_t pin_number, nrf_gpio_pin_pull_t pull_config, nrf_gpio_pin_sense_t sense_config)
	Function for configuring the given GPIO pin number as input with given initial value set, hiding inner details. This function can be used to configure pin range as simple input with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases). Sense capability on the pin is configurable, and input is connected to buffer so that the GPIO->IN register is readable. More...

static __INLINE void	nrf_gpio_pin_dir_set (uint32_t pin_number, nrf_gpio_pin_dir_t direction)
	Function for setting the direction for a GPIO pin. More...

static __INLINE void	nrf_gpio_pin_set (uint32_t pin_number)
	Function for setting a GPIO pin. More...

static __INLINE void	nrf_gpio_pin_clear (uint32_t pin_number)
	Function for clearing a GPIO pin. More...

static __INLINE void	nrf_gpio_pin_toggle (uint32_t pin_number)
	Function for toggling a GPIO pin. More...

static __INLINE void	nrf_gpio_pin_write (uint32_t pin_number, uint32_t value)
	Function for writing a value to a GPIO pin. More...

static __INLINE uint32_t	nrf_gpio_pin_read (uint32_t pin_number)
	Function for reading the input level of a GPIO pin. More...

static __INLINE void	nrf_gpio_word_byte_write (volatile uint32_t *word_address, uint8_t byte_no, uint8_t value)
	Generic function for writing a single byte of a 32 bit word at a given address. More...

static __INLINE uint8_t	nrf_gpio_word_byte_read (const volatile uint32_t *word_address, uint8_t byte_no)
	Generic function for reading a single byte of a 32 bit word at a given address. More...

static __INLINE void	nrf_gpio_port_dir_set (nrf_gpio_port_select_t port, nrf_gpio_port_dir_t dir)
	Function for setting the direction of a port. More...

static __INLINE uint8_t	nrf_gpio_port_read (nrf_gpio_port_select_t port)
	Function for reading a GPIO port. More...

static __INLINE void	nrf_gpio_port_write (nrf_gpio_port_select_t port, uint8_t value)
	Function for writing to a GPIO port. More...

static __INLINE void	nrf_gpio_port_set (nrf_gpio_port_select_t port, uint8_t set_mask)
	Function for setting individual pins on GPIO port. More...

static __INLINE void	nrf_gpio_port_clear (nrf_gpio_port_select_t port, uint8_t clr_mask)
	Function for clearing individual pins on GPIO port. More...

Detailed Description

GPIO pin abstraction and port abstraction for reading and writing byte-wise to GPIO ports.

Here, the GPIO ports are defined as follows:

Port 0 -> pin 0-7
Port 1 -> pin 8-15
Port 2 -> pin 16-23
Port 3 -> pin 24-31

Enumeration Type Documentation

enum nrf_gpio_pin_dir_t

Pin direction definitions.

Enumerator
NRF_GPIO_PIN_DIR_INPUT	Input.
NRF_GPIO_PIN_DIR_OUTPUT	Output.

enum nrf_gpio_pin_pull_t

Enumerator used for selecting the pin to be pulled down or up at the time of pin configuration.

Enumerator
NRF_GPIO_PIN_NOPULL	Pin pullup resistor disabled.
NRF_GPIO_PIN_PULLDOWN	Pin pulldown resistor enabled.
NRF_GPIO_PIN_PULLUP	Pin pullup resistor enabled.

enum nrf_gpio_pin_sense_t

Enumerator used for selecting the pin to sense high or low level on the pin input.

Enumerator
NRF_GPIO_PIN_NOSENSE	Pin sense level disabled.
NRF_GPIO_PIN_SENSE_LOW	Pin sense low level.
NRF_GPIO_PIN_SENSE_HIGH	Pin sense high level.

enum nrf_gpio_port_dir_t

Enumerator used for setting the direction of a GPIO port.

Enumerator
NRF_GPIO_PORT_DIR_OUTPUT	Output.
NRF_GPIO_PORT_DIR_INPUT	Input.

enum nrf_gpio_port_select_t

Enumerator used for selecting between port 0 - 3.

Enumerator
NRF_GPIO_PORT_SELECT_PORT0	Port 0 (GPIO pin 0-7)
NRF_GPIO_PORT_SELECT_PORT1	Port 1 (GPIO pin 8-15)
NRF_GPIO_PORT_SELECT_PORT2	Port 2 (GPIO pin 16-23)
NRF_GPIO_PORT_SELECT_PORT3	Port 3 (GPIO pin 24-31)

Function Documentation

static __INLINE void nrf_gpio_cfg_input	(	uint32_t	pin_number,
		nrf_gpio_pin_pull_t	pull_config
	)

static

Function for configuring the given GPIO pin number as input with given initial value set, hiding inner details. This function can be used to configure pin range as simple input with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases).

Parameters

pin_number	specifies the pin number of gpio pin numbers to be configured (allowed values 0-30)
pull_config	State of the pin range pull resistor (no pull, pulled down or pulled high)

Note: Sense capability on the pin is disabled, and input is connected to buffer so that the GPIO->IN register is readable

static __INLINE void nrf_gpio_cfg_output ( uint32_t pin_number )

static

Function for configuring the given GPIO pin number as output with given initial value set, hiding inner details. This function can be used to configure pin range as simple input with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases).

Parameters

pin_number specifies the pin number of gpio pin numbers to be configured (allowed values 0-30)

Note: Sense capability on the pin is disabled, and input is disconnected from the buffer as the pins are configured as output.

static __INLINE void nrf_gpio_cfg_sense_input	(	uint32_t	pin_number,
		nrf_gpio_pin_pull_t	pull_config,
		nrf_gpio_pin_sense_t	sense_config
	)

static

Function for configuring the given GPIO pin number as input with given initial value set, hiding inner details. This function can be used to configure pin range as simple input with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases). Sense capability on the pin is configurable, and input is connected to buffer so that the GPIO->IN register is readable.

Parameters

pin_number	specifies the pin number of gpio pin numbers to be configured (allowed values 0-30).
pull_config	state of the pin pull resistor (no pull, pulled down or pulled high).
sense_config	sense level of the pin (no sense, sense low or sense high).

static __INLINE void nrf_gpio_pin_clear ( uint32_t pin_number )

static

Function for clearing a GPIO pin.

Note that the pin must be configured as an output for this function to have any effect.

Parameters

pin_number specifies the pin number [0:31] to clear.

static __INLINE void nrf_gpio_pin_dir_set	(	uint32_t	pin_number,
		nrf_gpio_pin_dir_t	direction
	)

static

Function for setting the direction for a GPIO pin.

Parameters

pin_number	specifies the pin number [0:31] for which to set the direction.
direction	specifies the direction

static __INLINE uint32_t nrf_gpio_pin_read ( uint32_t pin_number )

static

Function for reading the input level of a GPIO pin.

Note that the pin must have input connected for the value returned from this function to be valid.

Parameters

pin_number specifies the pin number [0:31] to read.

Returns

Return values

0	if the pin input level is low.
1	if the pin input level is high.
>	1 should never occur.

static __INLINE void nrf_gpio_pin_set ( uint32_t pin_number )

static

Function for setting a GPIO pin.

Note that the pin must be configured as an output for this function to have any effect.

Parameters

pin_number specifies the pin number [0:31] to set.

static __INLINE void nrf_gpio_pin_toggle ( uint32_t pin_number )

static

Function for toggling a GPIO pin.

Note that the pin must be configured as an output for this function to have any effect.

Parameters

pin_number specifies the pin number [0:31] to toggle.

static __INLINE void nrf_gpio_pin_write	(	uint32_t	pin_number,
		uint32_t	value
	)

static

Function for writing a value to a GPIO pin.

Note that the pin must be configured as an output for this function to have any effect.

Parameters

pin_number	specifies the pin number [0:31] to write.
value	specifies the value to be written to the pin. 0 clears the pin >=1 sets the pin.

static __INLINE void nrf_gpio_port_clear	(	nrf_gpio_port_select_t	port,
		uint8_t	clr_mask
	)

static

Function for clearing individual pins on GPIO port.

Parameters

port	is the port for which to clear the pins.
clr_mask	is a mask specifying which pins to clear. A bit set to 1 indicates that the corresponding port pin shall be cleared.

See Also: nrf_gpio_port_dir_set()

static __INLINE void nrf_gpio_port_dir_set	(	nrf_gpio_port_select_t	port,
		nrf_gpio_port_dir_t	dir
	)

static

Function for setting the direction of a port.

Parameters

port	is the port for which to set the direction.
dir	direction to be set for this port.

static __INLINE uint8_t nrf_gpio_port_read ( nrf_gpio_port_select_t port )

static

Function for reading a GPIO port.

Parameters

port	is the port to read.

Returns: the input value on this port.

static __INLINE void nrf_gpio_port_set	(	nrf_gpio_port_select_t	port,
		uint8_t	set_mask
	)

static

Function for setting individual pins on GPIO port.

Parameters

port	is the port for which to set the pins.
set_mask	is a mask specifying which pins to set. A bit set to 1 indicates that the corresponding port pin shall be set.

See Also: nrf_gpio_port_dir_set()

static __INLINE void nrf_gpio_port_write	(	nrf_gpio_port_select_t	port,
		uint8_t	value
	)

static

Function for writing to a GPIO port.

Parameters

port	is the port to write.
value	is the value to write to this port.

See Also: nrf_gpio_port_dir_set()

static __INLINE void nrf_gpio_range_cfg_input	(	uint32_t	pin_range_start,
		uint32_t	pin_range_end,
		nrf_gpio_pin_pull_t	pull_config
	)

static

Function for configuring the GPIO pin range as inputs with given initial value set, hiding inner details. This function can be used to configure pin range as simple input.

Parameters

pin_range_start	specifies the start number (inclusive) in the range of pin numbers to be configured (allowed values 0-30)
pin_range_end	specifies the end number (inclusive) in the range of pin numbers to be configured (allowed values 0-30)
pull_config	State of the pin range pull resistor (no pull, pulled down or pulled high)

Note: For configuring only one pin as input use nrf_gpio_cfg_input Sense capability on the pin is disabled, and input is connected to buffer so that the GPIO->IN register is readable

static __INLINE void nrf_gpio_range_cfg_output	(	uint32_t	pin_range_start,
		uint32_t	pin_range_end
	)

static

Function for configuring the GPIO pin range as outputs with normal drive strength. This function can be used to configure pin range as simple output with gate driving GPIO_PIN_CNF_DRIVE_S0S1 (normal cases).

Parameters

pin_range_start	specifies the start number (inclusive) in the range of pin numbers to be configured (allowed values 0-30)
pin_range_end	specifies the end number (inclusive) in the range of pin numbers to be configured (allowed values 0-30)

Note: For configuring only one pin as output use nrf_gpio_cfg_output Sense capability on the pin is disabled, and input is disconnected from the buffer as the pins are configured as output.

static __INLINE uint8_t nrf_gpio_word_byte_read	(	const volatile uint32_t *	word_address,
		uint8_t	byte_no
	)

static

Generic function for reading a single byte of a 32 bit word at a given address.

This function should not be called from outside the nrf_gpio abstraction layer.

Parameters

word_address	is the address of the word to be read.
byte_no	is the the byte number (0-3) of the word to be read.

Returns: byte "byte_no" of word at address "word_address".

static __INLINE void nrf_gpio_word_byte_write	(	volatile uint32_t *	word_address,
		uint8_t	byte_no,
		uint8_t	value
	)

static

Generic function for writing a single byte of a 32 bit word at a given address.

This function should not be called from outside the nrf_gpio abstraction layer.

Parameters

word_address	is the address of the word to be written.
byte_no	is the the word byte number (0-3) to be written.
value	is the value to be written to byte "byte_no" of word at address "word_address"

Enumerations

Functions

Detailed Description

Enumeration Type Documentation

Function Documentation