UART driver¶
-
group
nrfx_uart
UART peripheral driver.
Defines
-
NRFX_UART_INSTANCE
(id)¶ Macro for creating a UART driver instance.
-
NRFX_UART_DEFAULT_EXTENDED_STOP_CONFIG
¶ UART additional stop bits configuration.
-
NRFX_UART_DEFAULT_EXTENDED_PARITYTYPE_CONFIG
¶ UART additional parity type configuration.
-
NRFX_UART_DEFAULT_CONFIG
(_pin_tx, _pin_rx)¶ UART driver default configuration.
This configuration sets up UART with the following options:
hardware flow control disabled
no parity bit
one stop bit
baudrate: 115200
- Parameters
_pin_tx – [in] TX pin.
_pin_rx – [in] RX pin.
Typedefs
-
typedef void (*
nrfx_uart_event_handler_t
)(nrfx_uart_event_t const *p_event, void *p_context)¶ UART interrupt event handler.
- Parameters
p_event – [in] Pointer to event structure. Event is allocated on the stack so it is available only within the context of the event handler.
p_context – [in] Context passed to the interrupt handler, set on initialization.
Enums
Functions
-
nrfx_err_t
nrfx_uart_init
(nrfx_uart_t const *p_instance, nrfx_uart_config_t const *p_config, nrfx_uart_event_handler_t event_handler)¶ Function for initializing the UART driver.
This function configures and enables UART. After this function GPIO pins are controlled by UART.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
p_config – [in] Pointer to the structure with the initial configuration.
event_handler – [in] Event handler provided by the user. If not provided, the driver works in blocking mode.
- Returns NRFX_SUCCESS
Initialization is successful.
- Returns NRFX_ERROR_INVALID_STATE
The driver is already initialized.
- Returns NRFX_ERROR_BUSY
Some other peripheral with the same instance ID is already in use. This is possible only if Peripheral Resource Sharing (PRS) module is enabled.
-
void
nrfx_uart_uninit
(nrfx_uart_t const *p_instance)¶ Function for uninitializing the UART driver.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
-
NRFX_STATIC_INLINE uint32_t
nrfx_uart_task_address_get
(nrfx_uart_t const *p_instance, nrf_uart_task_t task)¶ Function for getting the address of the specified UART task.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
task – [in] Task.
- Returns
Task address.
-
NRFX_STATIC_INLINE uint32_t
nrfx_uart_event_address_get
(nrfx_uart_t const *p_instance, nrf_uart_event_t event)¶ Function for getting the address of the specified UART event.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
event – [in] Event.
- Returns
Event address.
-
nrfx_err_t
nrfx_uart_tx
(nrfx_uart_t const *p_instance, uint8_t const *p_data, size_t length)¶ Function for sending data over UART.
If an event handler was provided in nrfx_uart_init() call, this function returns immediately and the handler is called when the transfer is done. Otherwise, the transfer is performed in blocking mode, that is this function returns when the transfer is finished. Blocking mode is not using interrupt so there is no context switching inside the function.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
p_data – [in] Pointer to data.
length – [in] Number of bytes to send.
- Returns NRFX_SUCCESS
Initialization was successful.
- Returns NRFX_ERROR_BUSY
Driver is already transferring.
- Returns NRFX_ERROR_FORBIDDEN
The transfer was aborted from a different context (blocking mode only).
-
bool
nrfx_uart_tx_in_progress
(nrfx_uart_t const *p_instance)¶ Function for checking if UART is currently transmitting.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
- Returns true
The UART is transmitting.
- Returns false
The UART is not transmitting.
-
void
nrfx_uart_tx_abort
(nrfx_uart_t const *p_instance)¶ Function for aborting any ongoing transmission.
Note
NRFX_UART_EVT_TX_DONE event will be generated in non-blocking mode. It will contain number of bytes sent until the abort was called. The event handler will be called from the function context.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
-
nrfx_err_t
nrfx_uart_rx
(nrfx_uart_t const *p_instance, uint8_t *p_data, size_t length)¶ Function for receiving data over UART.
If an event handler is provided in the nrfx_uart_init() call, this function returns immediately and the handler is called when the transfer is done. Otherwise, the transfer is performed in blocking mode, that is this function returns when the transfer is finished. Blocking mode is not using interrupt so there is no context switching inside the function. The receive buffer pointer is double-buffered in non-blocking mode. The secondary buffer can be set immediately after starting the transfer and will be filled when the primary buffer is full. The double-buffering feature allows receiving data continuously.
If this function is used without a previous call to nrfx_uart_rx_enable, the reception will be stopped on error or when the supplied buffer fills up. In both cases, RX FIFO gets disabled. This means that, in case of error, the bytes that follow are lost. If this nrfx_uart_rx() function is used with the previous call to nrfx_uart_rx_enable, the reception is stopped in case of error, but FIFO is still ongoing. The receiver is still working, so after handling the error, an immediate repeated call to this nrfx_uart_rx() function with fresh data buffer will re-establish reception. To disable the receiver, you must call nrfx_uart_rx_disable explicitly.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
p_data – [in] Pointer to data.
length – [in] Number of bytes to receive.
- Returns NRFX_SUCCESS
Reception is complete (in case of blocking mode) or it is successfully started (in case of non-blocking mode).
- Returns NRFX_ERROR_BUSY
The driver is already receiving (and the secondary buffer has already been set in non-blocking mode).
- Returns NRFX_ERROR_FORBIDDEN
The transfer was aborted from a different context (blocking mode only, also see nrfx_uart_rx_disable).
- Returns NRFX_ERROR_INTERNAL
The UART peripheral reported an error.
-
bool
nrfx_uart_rx_ready
(nrfx_uart_t const *p_instance)¶ Function for testing the receiver state in blocking mode.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
- Returns true
The receiver has at least one byte of data to get.
- Returns false
The receiver is empty.
-
void
nrfx_uart_rx_enable
(nrfx_uart_t const *p_instance)¶ Function for enabling the receiver.
UART has a 6-byte-long RX FIFO and it is used to store incoming data. If a user does not call the UART receive function before the FIFO is filled, an overrun error will appear. The receiver must be explicitly closed by the user
- Parameters
p_instance – [in] Pointer to the driver instance structure.
-
void
nrfx_uart_rx_disable
(nrfx_uart_t const *p_instance)¶ Function for disabling the receiver.
This function must be called to close the receiver after it has been explicitly enabled by
- Parameters
p_instance – [in] Pointer to the driver instance structure.
-
void
nrfx_uart_rx_abort
(nrfx_uart_t const *p_instance)¶ Function for aborting any ongoing reception.
Note
NRFX_UART_EVT_TX_DONE event will be generated in non-blocking mode. It will contain number of bytes received until the abort was called. The event handler will be called from the UART interrupt context.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
-
uint32_t
nrfx_uart_errorsrc_get
(nrfx_uart_t const *p_instance)¶ Function for reading error source mask. Mask contains values from nrf_uart_error_mask_t.
Note
Function must be used in blocking mode only. In case of non-blocking mode, an error event is generated. Function clears error sources after reading.
- Parameters
p_instance – [in] Pointer to the driver instance structure.
- Returns
Mask of reported errors.
-
struct
nrfx_uart_t
¶ - #include <nrfx_uart.h>
Data structure of the UART driver instance.
-
struct
nrfx_uart_config_t
¶ - #include <nrfx_uart.h>
Structure for the UART configuration.
Public Members
-
uint32_t
pseltxd
¶ TXD pin number.
-
uint32_t
pselrxd
¶ RXD pin number.
-
uint32_t
pselcts
¶ CTS pin number.
-
uint32_t
pselrts
¶ RTS pin number.
-
void *
p_context
¶ Context passed to interrupt handler.
-
nrf_uart_baudrate_t
baudrate
¶ Baud rate.
-
uint8_t
interrupt_priority
¶ Interrupt priority.
-
nrf_uart_config_t
hal_cfg
¶ Parity, flow control and stop bits settings.
-
uint32_t
-
struct
nrfx_uart_xfer_evt_t
¶ - #include <nrfx_uart.h>
Structure for the UART transfer completion event.
-
struct
nrfx_uart_error_evt_t
¶ - #include <nrfx_uart.h>
Structure for the UART error event.
Public Members
-
nrfx_uart_xfer_evt_t
rxtx
¶ Transfer details, including number of bytes transferred.
-
uint32_t
error_mask
¶ Mask of error flags that generated the event.
-
nrfx_uart_xfer_evt_t
-
struct
nrfx_uart_event_t
¶ - #include <nrfx_uart.h>
Structure for the UART event.
Public Members
-
nrfx_uart_evt_type_t
type
¶ Event type.
-
nrfx_uart_xfer_evt_t
rxtx
¶ Data provided for transfer completion events.
-
nrfx_uart_error_evt_t
error
¶ Data provided for error event.
-
union nrfx_uart_event_t.[anonymous]
data
¶ Union to store event data.
-
nrfx_uart_evt_type_t
-