SAADC HAL¶
-
group
nrf_saadc_hal
Hardware access layer for managing the SAADC peripheral.
Typedefs
-
typedef int16_t
nrf_saadc_value_t
¶ Type of a single ADC conversion result.
Enums
-
enum
nrf_saadc_resolution_t
¶ Resolution of the analog-to-digital converter.
Values:
-
enumerator
NRF_SAADC_RESOLUTION_8BIT
¶ 8 bit resolution.
-
enumerator
NRF_SAADC_RESOLUTION_10BIT
¶ 10 bit resolution.
-
enumerator
NRF_SAADC_RESOLUTION_12BIT
¶ 12 bit resolution.
-
enumerator
NRF_SAADC_RESOLUTION_14BIT
¶ 14 bit resolution.
-
enumerator
-
enum
nrf_saadc_input_t
¶ Input selection for the analog-to-digital converter.
Values:
-
enumerator
NRF_SAADC_INPUT_DISABLED
¶ Not connected.
-
enumerator
NRF_SAADC_INPUT_AIN0
¶ Analog input 0 (AIN0).
-
enumerator
NRF_SAADC_INPUT_AIN1
¶ Analog input 1 (AIN1).
-
enumerator
NRF_SAADC_INPUT_AIN2
¶ Analog input 2 (AIN2).
-
enumerator
NRF_SAADC_INPUT_AIN3
¶ Analog input 3 (AIN3).
-
enumerator
NRF_SAADC_INPUT_AIN4
¶ Analog input 4 (AIN4).
-
enumerator
NRF_SAADC_INPUT_AIN5
¶ Analog input 5 (AIN5).
-
enumerator
NRF_SAADC_INPUT_AIN6
¶ Analog input 6 (AIN6).
-
enumerator
NRF_SAADC_INPUT_AIN7
¶ Analog input 7 (AIN7).
-
enumerator
NRF_SAADC_INPUT_VDD
¶ VDD as input.
-
enumerator
NRF_SAADC_INPUT_VDDHDIV5
¶ VDDH/5 as input.
-
enumerator
-
enum
nrf_saadc_oversample_t
¶ Analog-to-digital converter oversampling mode.
Values:
-
enumerator
NRF_SAADC_OVERSAMPLE_DISABLED
¶ No oversampling.
-
enumerator
NRF_SAADC_OVERSAMPLE_2X
¶ Oversample 2x.
-
enumerator
NRF_SAADC_OVERSAMPLE_4X
¶ Oversample 4x.
-
enumerator
NRF_SAADC_OVERSAMPLE_8X
¶ Oversample 8x.
-
enumerator
NRF_SAADC_OVERSAMPLE_16X
¶ Oversample 16x.
-
enumerator
NRF_SAADC_OVERSAMPLE_32X
¶ Oversample 32x.
-
enumerator
NRF_SAADC_OVERSAMPLE_64X
¶ Oversample 64x.
-
enumerator
NRF_SAADC_OVERSAMPLE_128X
¶ Oversample 128x.
-
enumerator
NRF_SAADC_OVERSAMPLE_256X
¶ Oversample 256x.
-
enumerator
-
enum
nrf_saadc_resistor_t
¶ Analog-to-digital converter channel resistor control.
Values:
-
enumerator
NRF_SAADC_RESISTOR_DISABLED
¶ Bypass resistor ladder.
-
enumerator
NRF_SAADC_RESISTOR_PULLDOWN
¶ Pull-down to GND.
-
enumerator
NRF_SAADC_RESISTOR_PULLUP
¶ Pull-up to VDD.
-
enumerator
NRF_SAADC_RESISTOR_VDD1_2
¶ Set input at VDD/2.
-
enumerator
-
enum
nrf_saadc_gain_t
¶ Gain factor of the analog-to-digital converter input.
Values:
-
enumerator
NRF_SAADC_GAIN1_6
¶ Gain factor 1/6.
-
enumerator
NRF_SAADC_GAIN1_5
¶ Gain factor 1/5.
-
enumerator
NRF_SAADC_GAIN1_4
¶ Gain factor 1/4.
-
enumerator
NRF_SAADC_GAIN1_3
¶ Gain factor 1/3.
-
enumerator
NRF_SAADC_GAIN1_2
¶ Gain factor 1/2.
-
enumerator
NRF_SAADC_GAIN1
¶ Gain factor 1.
-
enumerator
NRF_SAADC_GAIN2
¶ Gain factor 2.
-
enumerator
NRF_SAADC_GAIN4
¶ Gain factor 4.
-
enumerator
-
enum
nrf_saadc_reference_t
¶ Reference selection for the analog-to-digital converter.
Values:
-
enumerator
NRF_SAADC_REFERENCE_INTERNAL
¶ Internal reference (0.6 V).
-
enumerator
NRF_SAADC_REFERENCE_VDD4
¶ VDD/4 as reference.
-
enumerator
-
enum
nrf_saadc_acqtime_t
¶ Analog-to-digital converter acquisition time.
Values:
-
enumerator
NRF_SAADC_ACQTIME_3US
¶ 3 us.
-
enumerator
NRF_SAADC_ACQTIME_5US
¶ 5 us.
-
enumerator
NRF_SAADC_ACQTIME_10US
¶ 10 us.
-
enumerator
NRF_SAADC_ACQTIME_15US
¶ 15 us.
-
enumerator
NRF_SAADC_ACQTIME_20US
¶ 20 us.
-
enumerator
NRF_SAADC_ACQTIME_40US
¶ 40 us.
-
enumerator
-
enum
nrf_saadc_mode_t
¶ Analog-to-digital converter channel mode.
Values:
-
enumerator
NRF_SAADC_MODE_SINGLE_ENDED
¶ Single-ended mode. PSELN will be ignored, negative input to ADC shorted to GND.
-
enumerator
NRF_SAADC_MODE_DIFFERENTIAL
¶ Differential mode.
-
enumerator
-
enum
nrf_saadc_burst_t
¶ Analog-to-digital converter channel burst mode.
Values:
-
enumerator
NRF_SAADC_BURST_DISABLED
¶ Burst mode is disabled (normal operation).
-
enumerator
NRF_SAADC_BURST_ENABLED
¶ Burst mode is enabled. SAADC takes 2^OVERSAMPLE number of samples as fast as it can, and sends the average to Data RAM.
-
enumerator
-
enum
nrf_saadc_task_t
¶ Analog-to-digital converter tasks.
Values:
-
enumerator
NRF_SAADC_TASK_START
¶ Start the ADC and prepare the result buffer in RAM.
-
enumerator
NRF_SAADC_TASK_SAMPLE
¶ Take one ADC sample. If scan is enabled, all channels are sampled.
-
enumerator
NRF_SAADC_TASK_STOP
¶ Stop the ADC and terminate any ongoing conversion.
-
enumerator
NRF_SAADC_TASK_CALIBRATEOFFSET
¶ Starts offset auto-calibration.
-
enumerator
-
enum
nrf_saadc_event_t
¶ Analog-to-digital converter events.
Values:
-
enumerator
NRF_SAADC_EVENT_STARTED
¶ The ADC has started.
-
enumerator
NRF_SAADC_EVENT_END
¶ The ADC has filled up the result buffer.
-
enumerator
NRF_SAADC_EVENT_DONE
¶ A conversion task has been completed.
-
enumerator
NRF_SAADC_EVENT_RESULTDONE
¶ A result is ready to get transferred to RAM.
-
enumerator
NRF_SAADC_EVENT_CALIBRATEDONE
¶ Calibration is complete.
-
enumerator
NRF_SAADC_EVENT_STOPPED
¶ The ADC has stopped.
-
enumerator
NRF_SAADC_EVENT_CH0_LIMITH
¶ Last result is equal or above CH[0].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH0_LIMITL
¶ Last result is equal or below CH[0].LIMIT.LOW.
-
enumerator
NRF_SAADC_EVENT_CH1_LIMITH
¶ Last result is equal or above CH[1].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH1_LIMITL
¶ Last result is equal or below CH[1].LIMIT.LOW.
-
enumerator
NRF_SAADC_EVENT_CH2_LIMITH
¶ Last result is equal or above CH[2].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH2_LIMITL
¶ Last result is equal or below CH[2].LIMIT.LOW.
-
enumerator
NRF_SAADC_EVENT_CH3_LIMITH
¶ Last result is equal or above CH[3].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH3_LIMITL
¶ Last result is equal or below CH[3].LIMIT.LOW.
-
enumerator
NRF_SAADC_EVENT_CH4_LIMITH
¶ Last result is equal or above CH[4].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH4_LIMITL
¶ Last result is equal or below CH[4].LIMIT.LOW.
-
enumerator
NRF_SAADC_EVENT_CH5_LIMITH
¶ Last result is equal or above CH[5].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH5_LIMITL
¶ Last result is equal or below CH[5].LIMIT.LOW.
-
enumerator
NRF_SAADC_EVENT_CH6_LIMITH
¶ Last result is equal or above CH[6].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH6_LIMITL
¶ Last result is equal or below CH[6].LIMIT.LOW.
-
enumerator
NRF_SAADC_EVENT_CH7_LIMITH
¶ Last result is equal or above CH[7].LIMIT.HIGH.
-
enumerator
NRF_SAADC_EVENT_CH7_LIMITL
¶ Last result is equal or below CH[7].LIMIT.LOW.
-
enumerator
-
enum
nrf_saadc_int_mask_t
¶ Analog-to-digital converter interrupt masks.
Values:
-
enumerator
NRF_SAADC_INT_STARTED
¶ Interrupt on EVENTS_STARTED event.
-
enumerator
NRF_SAADC_INT_END
¶ Interrupt on EVENTS_END event.
-
enumerator
NRF_SAADC_INT_DONE
¶ Interrupt on EVENTS_DONE event.
-
enumerator
NRF_SAADC_INT_RESULTDONE
¶ Interrupt on EVENTS_RESULTDONE event.
-
enumerator
NRF_SAADC_INT_CALIBRATEDONE
¶ Interrupt on EVENTS_CALIBRATEDONE event.
-
enumerator
NRF_SAADC_INT_STOPPED
¶ Interrupt on EVENTS_STOPPED event.
-
enumerator
NRF_SAADC_INT_CH0LIMITH
¶ Interrupt on EVENTS_CH[0].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH0LIMITL
¶ Interrupt on EVENTS_CH[0].LIMITL event.
-
enumerator
NRF_SAADC_INT_CH1LIMITH
¶ Interrupt on EVENTS_CH[1].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH1LIMITL
¶ Interrupt on EVENTS_CH[1].LIMITL event.
-
enumerator
NRF_SAADC_INT_CH2LIMITH
¶ Interrupt on EVENTS_CH[2].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH2LIMITL
¶ Interrupt on EVENTS_CH[2].LIMITL event.
-
enumerator
NRF_SAADC_INT_CH3LIMITH
¶ Interrupt on EVENTS_CH[3].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH3LIMITL
¶ Interrupt on EVENTS_CH[3].LIMITL event.
-
enumerator
NRF_SAADC_INT_CH4LIMITH
¶ Interrupt on EVENTS_CH[4].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH4LIMITL
¶ Interrupt on EVENTS_CH[4].LIMITL event.
-
enumerator
NRF_SAADC_INT_CH5LIMITH
¶ Interrupt on EVENTS_CH[5].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH5LIMITL
¶ Interrupt on EVENTS_CH[5].LIMITL event.
-
enumerator
NRF_SAADC_INT_CH6LIMITH
¶ Interrupt on EVENTS_CH[6].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH6LIMITL
¶ Interrupt on EVENTS_CH[6].LIMITL event.
-
enumerator
NRF_SAADC_INT_CH7LIMITH
¶ Interrupt on EVENTS_CH[7].LIMITH event.
-
enumerator
NRF_SAADC_INT_CH7LIMITL
¶ Interrupt on EVENTS_CH[7].LIMITL event.
-
enumerator
NRF_SAADC_INT_ALL
¶ Mask of all interrupts.
-
enumerator
Functions
-
NRF_STATIC_INLINE void
nrf_saadc_task_trigger
(NRF_SAADC_Type *p_reg, nrf_saadc_task_t task)¶ Function for triggering the specified SAADC task.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
task – [in] SAADC task.
-
NRF_STATIC_INLINE uint32_t
nrf_saadc_task_address_get
(NRF_SAADC_Type const *p_reg, nrf_saadc_task_t task)¶ Function for getting the address of the specified SAADC task register.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
task – [in] SAADC task.
- Returns
Address of the specified SAADC task.
-
NRF_STATIC_INLINE bool
nrf_saadc_event_check
(NRF_SAADC_Type const *p_reg, nrf_saadc_event_t event)¶ Function for retrieving the state of the SAADC event.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
event – [in] Event to be checked.
- Returns true
The event has been generated.
- Returns false
The event has not been generated.
-
NRF_STATIC_INLINE void
nrf_saadc_event_clear
(NRF_SAADC_Type *p_reg, nrf_saadc_event_t event)¶ Function for clearing the specific SAADC event.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
event – [in] SAADC event.
-
NRF_STATIC_INLINE uint32_t
nrf_saadc_event_address_get
(NRF_SAADC_Type const *p_reg, nrf_saadc_event_t event)¶ Function for getting the address of the specified SAADC event register.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
event – [in] SAADC event.
- Returns
Address of the specified SAADC event.
-
NRF_STATIC_INLINE void
nrf_saadc_subscribe_set
(NRF_SAADC_Type *p_reg, nrf_saadc_task_t task, uint8_t channel)¶ Function for setting the subscribe configuration for a given SAADC task.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
task – [in] Task for which to set the configuration.
channel – [in] Channel through which to subscribe events.
-
NRF_STATIC_INLINE void
nrf_saadc_subscribe_clear
(NRF_SAADC_Type *p_reg, nrf_saadc_task_t task)¶ Function for clearing the subscribe configuration for a given SAADC task.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
task – [in] Task for which to clear the configuration.
-
NRF_STATIC_INLINE void
nrf_saadc_publish_set
(NRF_SAADC_Type *p_reg, nrf_saadc_event_t event, uint8_t channel)¶ Function for setting the publish configuration for a given SAADC event.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
event – [in] Event for which to set the configuration.
channel – [in] Channel through which to publish the event.
-
NRF_STATIC_INLINE void
nrf_saadc_publish_clear
(NRF_SAADC_Type *p_reg, nrf_saadc_event_t event)¶ Function for clearing the publish configuration for a given SAADC event.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
event – [in] Event for which to clear the configuration.
-
NRF_STATIC_INLINE nrf_saadc_event_t
nrf_saadc_limit_event_get
(uint8_t channel, nrf_saadc_limit_t limit_type)¶ Function for getting the SAADC channel monitoring limit events.
- Parameters
channel – [in] Channel number.
limit_type – [in] Low limit or high limit.
- Returns
The SAADC channel monitoring limit event.
-
NRF_STATIC_INLINE void
nrf_saadc_channel_input_set
(NRF_SAADC_Type *p_reg, uint8_t channel, nrf_saadc_input_t pselp, nrf_saadc_input_t pseln)¶ Function for configuring the input pins for the specified SAADC channel.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
channel – [in] Channel number.
pselp – [in] Positive input.
pseln – [in] Negative input. Set to NRF_SAADC_INPUT_DISABLED in single ended mode.
-
NRF_STATIC_INLINE void
nrf_saadc_channel_pos_input_set
(NRF_SAADC_Type *p_reg, uint8_t channel, nrf_saadc_input_t pselp)¶ Function for configuring the positive input pin for the specified SAADC channel.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
channel – [in] Channel number.
pselp – [in] Positive input.
-
NRF_STATIC_INLINE void
nrf_saadc_channel_limits_set
(NRF_SAADC_Type *p_reg, uint8_t channel, int16_t low, int16_t high)¶ Function for setting the SAADC channel monitoring limits.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
channel – [in] Channel number.
low – [in] Low limit.
high – [in] High limit.
-
NRF_STATIC_INLINE void
nrf_saadc_int_set
(NRF_SAADC_Type *p_reg, uint32_t mask)¶ Function for setting the configuration of SAADC interrupts.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
mask – [in] Interrupts configuration to be set.
-
NRF_STATIC_INLINE void
nrf_saadc_int_enable
(NRF_SAADC_Type *p_reg, uint32_t mask)¶ Function for enabling specified SAADC interrupts.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
mask – [in] Mask of interrupts to be enabled.
-
NRF_STATIC_INLINE uint32_t
nrf_saadc_int_enable_check
(NRF_SAADC_Type const *p_reg, uint32_t mask)¶ Function for checking if the specified interrupts are enabled.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
mask – [in] Mask of interrupts to be checked.
- Returns
Mask of enabled interrupts.
-
NRF_STATIC_INLINE void
nrf_saadc_int_disable
(NRF_SAADC_Type *p_reg, uint32_t mask)¶ Function for disabling specified interrupts.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
mask – [in] Mask of interrupts to be disabled.
-
NRF_STATIC_INLINE uint32_t
nrf_saadc_limit_int_get
(uint8_t channel, nrf_saadc_limit_t limit_type)¶ Function for generating masks for SAADC channel limit interrupts.
- Parameters
channel – [in] SAADC channel number.
limit_type – [in] Limit type.
- Returns
Interrupt mask.
-
NRF_STATIC_INLINE bool
nrf_saadc_busy_check
(NRF_SAADC_Type const *p_reg)¶ Function for checking whether the SAADC is busy.
This function checks whether the analog-to-digital converter is busy with a conversion.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
- Returns true
The SAADC is busy.
- Returns false
The SAADC is not busy.
-
NRF_STATIC_INLINE void
nrf_saadc_enable
(NRF_SAADC_Type *p_reg)¶ Function for enabling the SAADC.
The analog-to-digital converter must be enabled before use.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
-
NRF_STATIC_INLINE void
nrf_saadc_disable
(NRF_SAADC_Type *p_reg)¶ Function for disabling the SAADC.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
-
NRF_STATIC_INLINE bool
nrf_saadc_enable_check
(NRF_SAADC_Type const *p_reg)¶ Function for checking if the SAADC is enabled.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
- Returns true
The SAADC is enabled.
- Returns false
The SAADC is not enabled.
-
NRF_STATIC_INLINE void
nrf_saadc_buffer_init
(NRF_SAADC_Type *p_reg, nrf_saadc_value_t *p_buffer, uint32_t size)¶ Function for initializing the SAADC result buffer.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
p_buffer – [in] Pointer to the result buffer.
size – [in] Size of the buffer (in 16-bit samples).
-
NRF_STATIC_INLINE void
nrf_saadc_buffer_pointer_set
(NRF_SAADC_Type *p_reg, nrf_saadc_value_t *p_buffer)¶ Function for setting the SAADC result buffer pointer.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
p_buffer – [in] Pointer to the result buffer.
-
NRF_STATIC_INLINE nrf_saadc_value_t *
nrf_saadc_buffer_pointer_get
(NRF_SAADC_Type const *p_reg)¶ Function for getting the SAADC result buffer pointer.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
- Returns
Pointer to the result buffer.
-
NRF_STATIC_INLINE uint16_t
nrf_saadc_amount_get
(NRF_SAADC_Type const *p_reg)¶ Function for getting the number of samples written to the result buffer since the previous START task.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
- Returns
Number of 16-bit samples written to the buffer.
-
NRF_STATIC_INLINE void
nrf_saadc_resolution_set
(NRF_SAADC_Type *p_reg, nrf_saadc_resolution_t resolution)¶ Function for setting the SAADC sample resolution.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
resolution – [in] Bit resolution.
-
NRF_STATIC_INLINE nrf_saadc_resolution_t
nrf_saadc_resolution_get
(NRF_SAADC_Type const *p_reg)¶ Function for getting the SAADC sample resolution.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
- Returns
Sample resolution.
-
NRF_STATIC_INLINE void
nrf_saadc_oversample_set
(NRF_SAADC_Type *p_reg, nrf_saadc_oversample_t oversample)¶ Function for configuring the oversampling feature.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
oversample – [in] Oversampling mode.
-
NRF_STATIC_INLINE nrf_saadc_oversample_t
nrf_saadc_oversample_get
(NRF_SAADC_Type const *p_reg)¶ Function for getting the oversampling feature configuration.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
- Returns
Oversampling configuration.
-
NRF_STATIC_INLINE uint32_t
nrf_saadc_oversample_sample_count_get
(nrf_saadc_oversample_t oversample)¶ Function for getting the sample count needed for one averaged result for a given oversampling configuration.
- Parameters
oversample – [in] Oversampling configuration.
- Returns
Sample count.
-
NRF_STATIC_INLINE void
nrf_saadc_continuous_mode_enable
(NRF_SAADC_Type *p_reg, uint16_t cc)¶ Function for enabling the continuous sampling.
This function configures the SAADC internal timer to automatically take new samples at a fixed sample rate. Trigger the START task to begin continuous sampling. To stop the sampling, trigger the STOP task.
Note
The internal timer can only be used when a single input channel is enabled.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
cc – [in] Capture and compare value. Sample rate is 16 MHz/cc. Valid
CC
range is from 80 to 2047.
-
NRF_STATIC_INLINE bool
nrf_saadc_continuous_mode_enable_check
(NRF_SAADC_Type const *p_reg)¶ Function for checking if the continuous sampling is enabled.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
- Returns true
The continuous sampling is enabled.
- Returns false
The continuous sampling is disabled.
-
NRF_STATIC_INLINE void
nrf_saadc_continuous_mode_disable
(NRF_SAADC_Type *p_reg)¶ Function for disabling the continuous sampling.
New samples can still be acquired by manually triggering the SAMPLE task or by PPI.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
-
NRF_STATIC_INLINE void
nrf_saadc_channel_init
(NRF_SAADC_Type *p_reg, uint8_t channel, nrf_saadc_channel_config_t const *config)¶ Function for initializing the SAADC channel.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
channel – [in] Channel number.
config – [in] Pointer to the channel configuration structure.
-
NRF_STATIC_INLINE void
nrf_saadc_burst_set
(NRF_SAADC_Type *p_reg, uint8_t channel, nrf_saadc_burst_t burst)¶ Function for configuring the burst mode for the specified channel.
- Parameters
p_reg – [in] Pointer to the structure of registers of the peripheral.
channel – [in] Channel number.
burst – [in] Burst mode setting.
-
NRF_STATIC_INLINE nrf_saadc_value_t
nrf_saadc_value_min_get
(nrf_saadc_resolution_t resolution)¶ Function for getting the minimum value of the conversion result.
The minimum value of the conversion result depends on the configured resolution.
- Parameters
resolution – [in] Bit resolution.
- Returns
Minimum value of the conversion result.
-
NRF_STATIC_INLINE nrf_saadc_value_t
nrf_saadc_value_max_get
(nrf_saadc_resolution_t resolution)¶ Function for getting the maximum value of the conversion result.
The maximum value of the conversion result depends on the configured resolution.
- Parameters
resolution – [in] Bit resolution.
- Returns
Maximum value of the conversion result.
-
struct
nrf_saadc_config_t
¶ - #include <nrf_saadc.h>
Analog-to-digital converter configuration structure.
Public Members
-
nrf_saadc_resolution_t
resolution
¶ Resolution of samples.
-
nrf_saadc_oversample_t
oversample
¶ Oversampling configuration.
-
nrf_saadc_value_t *
buffer
¶ Pointer to sample buffer.
-
uint32_t
buffer_size
¶ Size of the sample buffer.
-
nrf_saadc_resolution_t
-
struct
nrf_saadc_channel_config_t
¶ - #include <nrf_saadc.h>
Analog-to-digital converter channel configuration structure.
Public Members
-
nrf_saadc_resistor_t
resistor_p
¶ Resistor value on positive input.
-
nrf_saadc_resistor_t
resistor_n
¶ Resistor value on negative input.
-
nrf_saadc_gain_t
gain
¶ Gain control value.
-
nrf_saadc_reference_t
reference
¶ Reference control value.
-
nrf_saadc_acqtime_t
acq_time
¶ Acquisition time.
-
nrf_saadc_mode_t
mode
¶ SAADC mode. Single-ended or differential.
-
nrf_saadc_burst_t
burst
¶ Burst mode configuration.
-
nrf_saadc_resistor_t
-
typedef int16_t