-
CONFIG_BOARD_ENABLE_CPUNET
¶
Enable nRF53 Network MCU
Enable nRF53 Network MCU
Enable nRF53 Network MCU
Type: bool
Help¶
This option enables releasing the Network 'force off' signal, which
as a consequence will power up the Network MCU during system boot.
Additionally, the option allocates GPIO pins that will be used by UARTE
of the Network MCU.
Note: GPIO pin allocation can only be configured by the secure Application
MCU firmware, so when this option is used with the non-secure version of
the board, the application needs to take into consideration, that the
secure firmware image must already have configured GPIO allocation for the
Network MCU.
Help¶
This option enables releasing the Network 'force off' signal, which
as a consequence will power up the Network MCU during system boot.
Additionally, the option allocates GPIO pins that will be used by UARTE
of the Network MCU.
Note: GPIO pin allocation can only be configured by the secure Application
MCU firmware, so when this option is used with the non-secure version of
the board, the application needs to take into consideration, that the
secure firmware image must already have configured GPIO allocation for the
Network MCU.
Help¶
This option enables releasing the Network 'force off' signal, which
as a consequence will power up the Network MCU during system boot.
Additionally, the option allocates GPIO pins that will be used by UARTE
of the Network MCU.
Note: GPIO pin allocation can only be configured by the secure Application
MCU firmware, so when this option is used with the non-secure version of
the board, the application needs to take into consideration, that the
secure firmware image must already have configured GPIO allocation for the
Network MCU.
Direct dependencies¶
BOARD_BL5340_DVK_CPUAPP
|| BOARD_BL5340_DVK_CPUAPPNS
|| BOARD_NRF5340DK_NRF5340_CPUAPP
|| BOARD_NRF5340DK_NRF5340_CPUAPPNS
|| BOARD_THINGY53_NRF5340_CPUAPP
|| BOARD_THINGY53_NRF5340_CPUAPPNS
(Includes any dependencies from ifs and menus.)
Defaults¶
y if
BT
||NRF_802154_SER_HOST
y if
BT
||NRF_802154_SER_HOST
y if
BT
||NRF_802154_SER_HOST
Symbols that select this symbol¶
Kconfig definitions¶
At <Zephyr>/boards/arm/bl5340_dvk/Kconfig:70
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:27
→ <Zephyr>/boards/Kconfig:57
Menu path: (Top) → Board Options
config BOARD_ENABLE_CPUNET
bool "Enable nRF53 Network MCU"
default y if BT || NRF_802154_SER_HOST
depends on BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPPNS
help
This option enables releasing the Network 'force off' signal, which
as a consequence will power up the Network MCU during system boot.
Additionally, the option allocates GPIO pins that will be used by UARTE
of the Network MCU.
Note: GPIO pin allocation can only be configured by the secure Application
MCU firmware, so when this option is used with the non-secure version of
the board, the application needs to take into consideration, that the
secure firmware image must already have configured GPIO allocation for the
Network MCU.
At <Zephyr>/boards/arm/nrf5340dk_nrf5340/Kconfig:69
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:27
→ <Zephyr>/boards/Kconfig:57
Menu path: (Top) → Board Options
config BOARD_ENABLE_CPUNET
bool "Enable nRF53 Network MCU"
default y if BT || NRF_802154_SER_HOST
depends on BOARD_NRF5340DK_NRF5340_CPUAPP || BOARD_NRF5340DK_NRF5340_CPUAPPNS
help
This option enables releasing the Network 'force off' signal, which
as a consequence will power up the Network MCU during system boot.
Additionally, the option allocates GPIO pins that will be used by UARTE
of the Network MCU.
Note: GPIO pin allocation can only be configured by the secure Application
MCU firmware, so when this option is used with the non-secure version of
the board, the application needs to take into consideration, that the
secure firmware image must already have configured GPIO allocation for the
Network MCU.
At <Zephyr>/boards/arm/thingy53_nrf5340/Kconfig:72
Included via <Zephyr>/Kconfig:8
→ <Zephyr>/Kconfig.zephyr:27
→ <Zephyr>/boards/Kconfig:57
Menu path: (Top) → Board Options
config BOARD_ENABLE_CPUNET
bool "Enable nRF53 Network MCU"
default y if BT || NRF_802154_SER_HOST
depends on BOARD_THINGY53_NRF5340_CPUAPP || BOARD_THINGY53_NRF5340_CPUAPPNS
help
This option enables releasing the Network 'force off' signal, which
as a consequence will power up the Network MCU during system boot.
Additionally, the option allocates GPIO pins that will be used by UARTE
of the Network MCU.
Note: GPIO pin allocation can only be configured by the secure Application
MCU firmware, so when this option is used with the non-secure version of
the board, the application needs to take into consideration, that the
secure firmware image must already have configured GPIO allocation for the
Network MCU.
(The ‘depends on’ condition includes propagated dependencies from ifs and menus.)