nxp,imx8m-pinctrl

Vendor: NXP Semiconductors

Description

The node has the 'pinctrl' node label set in MCUX SoC's devicetree. These
nodes can be autogenerated using the MCUXpresso config tools combined with
the imx_dts_gen.py script in NXP's HAL. The mux, mode, input, daisy, and cfg
fields in a group select the pins to be configured, and the remaining
devicetree properties set configuration values for those pins
for example, here is an group configuring UART2 pins:

group0 {
    pinmux = <&iomuxc_uart2_rxd_uart_rx_uart2_rx,
        &iomuxc_uart2_txd_uart_tx_uart2_tx>;
    drive-strength = "40-ohm";
    slew-rate = "slow";
};

This will select UART2_RXD as UART2 rx, and UART2_TXD as UART2 tx.
Both pins will be configured with a slow slew rate, and maximum drive
strength.
Note that the soc level iomuxc dts file can be examined to find the possible
pinmux options. Here are the affects of each property on the
IOMUXC SW_PAD_CTL register:
nxp,lvttl: LVTTL=1
input-schmitt-enable: HYS=1
bias-pull-up: PUE=1
drive-open-drain: ODE=1
slew-rate: SRE=<enum_idx>
drive-strength: DSE=<enum_idx>
input-enable: SION=1 (in SW_MUX_CTL_PAD register)

If only required properties are supplied, the pin will have the following
configuration:
LVTLL=0,
HYS=0,
PUE=0,
ODE=0,
SRE=<slew-rate>,
DSE=<drive-strength>,
SION=0,

Properties

Top level properties

These property descriptions apply to “nxp,imx8m-pinctrl” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

(None)

Grandchild node properties

Name

Type

Details

pinmux

phandles

Pin mux selections for this group. See the soc level iomuxc DTSI file
for a defined list of these options.

This property is required.

drive-strength

string

Pin output drive strength. Sets the DSE field in the IOMUXC peripheral.
the drive strength is expressed as a output impedance at a given voltage,
but maximum current values can be calculated from these impedances
for a specific load impedance.
000 HI-Z — Output driver is disabled (Hi-Z State)
001 255_OHM — 255 Ohm @3.3V, 240 Ohm @2.5V, 230 Ohm @1.8V, 265 Ohm @1.2V
010 105_OHM — 105 Ohm @3.3V, 100 Ohm @2.5V, 85 Ohm @1.8V, 110 Ohm @1.2V
011 75_OHM — 75 Ohm @3.3V, 70 Ohm @2.5V, 60 Ohm @1.8V, 80 Ohm @1.2V
100 85_OHM — 85 Ohm @3.3V, 80 Ohm @2.5V, 75 Ohm @1.8V, 90 Ohm @1.2V
101 65_OHM — 65 Ohm @3.3V, 60 Ohm @2.5V, 55 Ohm @1.8V, 65 Ohm @1.2V
110 45_OHM — 45 Ohm @3.3V, 45 Ohm @2.5V, 40 Ohm @1.8V, 50 Ohm @1.2V
111 40_OHM — 40 Ohm @3.3V, 40 Ohm @2.5V, 33 Ohm @1.8V, 40 Ohm @1.2V

This property is required.

Legal values: 'disabled', '255-ohm', '105-ohm', '75-ohm', '85-ohm', '65-ohm', '45-ohm', '40-ohm'

slew-rate

string

Select slew rate for pin. Corresponds to SRE field in IOMUXC peripheral
00 SLOW — Slow Frequency Slew Rate (50Mhz)
01 MEDIUM — Medium Frequency Slew Rate (100Mhz)
10 FAST — Fast Frequency Slew Rate (150Mhz)
11 MAX — Max Frequency Slew Rate (200Mhz)

This property is required.

Legal values: 'slow', 'medium', 'fast', 'max'

nxp,lvttl

boolean

Enable LVTTL input. Sets LVTTL field in IOMUXC peripheral

bias-pull-up

boolean

enable pull-up resistor

bias-pull-down

boolean

enable pull-down resistor

drive-open-drain

boolean

drive with open drain (hardware AND)

input-enable

boolean

enable input on pin (e.g. enable an input buffer, no effect on output)

input-schmitt-enable

boolean

enable schmitt-trigger mode