NXP RDDRONE-FMUK66

Overview

The RDDRONE FMUK66 is an drone control board with commonly used peripheral connectors and a Kinetis K66 on board.

  • Comes with a J-Link Edu Mini for programming and UART console.

RDDRONE-FMUK66

Hardware

  • MK66FN2MOVLQ18 MCU (180 MHz, 2 MB flash memory, 256 KB RAM, low-power, crystal-less USB, and 144 Low profile Quad Flat Package (LQFP))

  • Dual role USB interface with micro-B USB connector

  • RGB LED

  • FXOS8700CQ accelerometer and magnetometer

  • FXAS21002CQ gyro

  • BMM150 magnetometer

  • ML3114A2 barometer

  • BMP280 barometer

  • Connector for PWM servo/motor controls

  • Connector for UART GPS/GLONASS

  • SDHC

For more information about the K64F SoC and FRDM-K64F board:

Supported Features

The rddrone-fmuk66 board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

SYSTICK

on-chip

systick

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

I2C

on-chip

i2c

SPI

on-chip

spi

WATCHDOG

on-chip

watchdog

ADC

on-chip

adc

DAC

on-chip

dac

PWM

on-chip

pwm

ETHERNET

on-chip

ethernet

UART

on-chip

serial port-polling; serial port-interrupt

FLASH

on-chip

soc flash

USB

on-chip

USB device

CAN

on-chip

can

RTC

on-chip

rtc

DMA

on-chip

dma

The default configuration can be found in the defconfig file:

boards/arm/rddrone_fmuk66/rddrone_fmuk66_defconfig

Other hardware features are not currently supported by the port.

System Clock

The K66F SoC is configured to use the 16 MHz external oscillator on the board with the on-chip PLL to generate a 160 MHz system clock.

Serial Port

The K66F SoC has six UARTs. LPUART0 is configured for the console, UART0 is labeled Serial 2, UART2 is labeled GPS, UART4 is labeled Serial 1. Any of these UARTs may be used as the console by overlaying the board device tree.

USB

The K66F SoC has a USB OTG (USBOTG) controller that supports both device and host functions through its micro USB connector (K66F USB). Only USB device function is supported in Zephyr at the moment.

Programming and Debugging

Build and flash applications as usual (see Building an Application and Run an Application for more details).

Configuring a Debug Probe

A debug probe is used for both flashing and debugging the board. This board is configured by default to use jlink. The board package with accessories comes with a jlink mini edu and cable specifically for this board along with a usb to uart that connects directly to the jlink mini edu. This is the expected default configuration for programming and getting a console.

# From the root of the zephyr repository
west build -b rddrone-fmuk66 samples/hello_world

Configuring a Console

Use the following settings with your serial terminal of choice (minicom, putty, etc.):

  • Speed: 115200

  • Data: 8 bits

  • Parity: None

  • Stop bits: 1

Flashing

Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b rddrone-fmuk66 samples/hello_world
west flash

Open a serial terminal, reset the board (press the SW1 button), and you should see the following message in the terminal:

***** Booting Zephyr OS v2.7.0 *****
Hello World! rddrone-fmuk66

Debugging

Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b rddrone-fmuk66 samples/hello_world
west debug

Open a serial terminal, step through the application in your debugger, and you should see the following message in the terminal:

***** Booting Zephyr OS v2.7.0 *****
Hello World! rddrone-fmuk66

https://www.nxp.com/design/designs/px4-robotic-drone-vehicle-flight-management-unit-vmu-fmu-rddrone-fmuk66:RDDRONE-FMUK66

https://nxp.gitbook.io/hovergames/userguide/getting-started

https://www.nxp.com/webapp/Download?colCode=SPF-39053

https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/general-purpose-mcus/k-series-cortex-m4/k6x-ethernet/kinetis-k66-180-mhz-dual-high-speed-full-speed-usbs-2mb-flash-microcontrollers-mcus-based-on-arm-cortex-m4-core:K66_180

https://www.nxp.com/docs/en/data-sheet/K66P144M180SF5V2.pdf

https://www.nxp.com/webapp/Download?colCode=K66P144M180SF5RMV2