ST Nucleo H753ZI

Overview

The STM32 Nucleo-144 boards offer combinations of performance and power that provide an affordable and flexible way for users to build prototypes and try out new concepts. For compatible boards, the SMPS (Switched-Mode Power Supply) significantly reduces power consumption in Run mode.

The Arduino-compatible ST Zio connector expands functionality of the Nucleo open development platform, with a wide choice of specialized Arduino* Uno V3 shields.

The STM32 Nucleo-144 board does not require any separate probe as it integrates the ST-LINK/V2-1 debugger/programmer.

The STM32 Nucleo-144 board comes with the STM32 comprehensive free software libraries and examples available with the STM32Cube MCU Package.

Key Features

  • STM32 microcontroller in LQFP144 package

  • Ethernet compliant with IEEE-802.3-2002 (depending on STM32 support)

  • USB OTG or full-speed device (depending on STM32 support)

  • 3 user LEDs

  • 2 user and reset push-buttons

  • 32.768 kHz crystal oscillator

  • Board connectors:

  • USB with Micro-AB

  • SWD

  • Ethernet RJ45 (depending on STM32 support)

  • ST Zio connector including Arduino* Uno V3

  • ST morpho

  • Flexible power-supply options: ST-LINK USB VBUS or external sources.

  • On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration

  • capability: mass storage, virtual COM port and debug port.

  • Comprehensive free software libraries and examples available with the STM32Cube MCU package.

  • Arm* Mbed Enabled* compliant (only for some Nucleo part numbers)

Nucleo H753ZI

More information about the board can be found at the Nucleo H753ZI website.

Hardware

Nucleo H753ZI provides the following hardware components:

  • STM32H753ZI in LQFP144 package

  • ARM 32-bit Cortex-M7 CPU with FPU

  • Chrom-ART Accelerator

  • Hardware JPEG Codec

  • 480 MHz max CPU frequency

  • VDD from 1.62 V to 3.6 V

  • 2 MB Flash

  • 1 MB SRAM

  • High-resolution timer (2.1 ns)

  • 32-bit timers(2)

  • 16-bit timers(12)

  • SPI(6)

  • I2C(4)

  • I2S (3)

  • USART(4)

  • UART(4)

  • USB OTG Full Speed and High Speed(1)

  • USB OTG Full Speed(1)

  • CAN FD(2)

  • SAI(2)

  • SPDIF_Rx(4)

  • HDMI_CEC(1)

  • Dual Mode Quad SPI(1)

  • Camera Interface

  • GPIO (up to 114) with external interrupt capability

  • 16-bit ADC(3) with 36 channels / 3.6 MSPS

  • 12-bit DAC with 2 channels(2)

  • True Random Number Generator (RNG)

  • 16-channel DMA

  • LCD-TFT Controller with XGA resolution

  • Cryptographic acceleration: AES 128, 192, 256, TDES, HASH (MD5, SHA-1, SHA-2), HMAC

  • Secure firmware upgrade support, Secure access mode

Supported Features

The Zephyr nucleo_h753zi board configuration supports the following hardware features:

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

UART

on-chip

serial port

PINMUX

on-chip

pinmux

GPIO

on-chip

gpio

RTC

on-chip

counter

I2C

on-chip

i2c

PWM

on-chip

pwm

ADC

on-chip

adc

RNG

on-chip

True Random number generator

ETHERNET

on-chip

ethernet

SPI

on-chip

spi

USB

on-chip

usb_device

CAN/CANFD

on-chip

canbus

Other hardware features are not yet supported on this Zephyr port.

The default configuration can be found in the defconfig file: boards/arm/nucleo_h753zi/nucleo_h753zi_defconfig

For mode details please refer to STM32 Nucleo-144 board User Manual.

Default Zephyr Peripheral Mapping:

The Nucleo H753ZI board features a ST Zio connector (extended Arduino Uno V3) and a ST morpho connector. Board is configured as follows:

  • UART_3 TX/RX : PD8/PD9 (ST-Link Virtual Port Com)

  • USER_PB : PC13

  • LD1 : PB0

  • LD2 : PB7

  • LD3 : PB14

  • I2C : PB8, PB9

  • ADC1_INP15 : PA3

  • ETH : PA1, PA2, PA7, PB13, PC1, PC4, PC5, PG11, PG13

  • SPI1 NSS/SCK/MISO/MOSI : PD14PA5/PA6/PB5 (Arduino SPI)

  • CAN/CANFD : PD0, PD1

System Clock

Nucleo H753ZI System Clock could be driven by an internal or external oscillator, as well as the main PLL clock. By default, the System clock is driven by the PLL clock at 96MHz, driven by an 8MHz high-speed external clock.

Serial Port

Nucleo H753ZI board has 4 UARTs and 4 USARTs. The Zephyr console output is assigned to UART3. Default settings are 115200 8N1.

CAN, CANFD

Requires an external CAN or CANFD transceiver.

Programming and Debugging

Applications for the nucleo_h753zi board configuration can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Note

If using OpenOCD you will need a recent development version as the last official release does not support H7 series yet. You can also choose the stm32cubeprogrammer runner.

Flashing

Nucleo H753ZI board includes an ST-LINK/V2-1 embedded debug tool interface.

Flashing an application to Nucleo H753ZI

Here is an example for the Hello World application.

Run a serial host program to connect with your Nucleo board.

$ minicom -b 115200 -D /dev/ttyACM0

Build and flash the application:

# From the root of the zephyr repository
west build -b nucleo_h753zi samples/hello_world
west flash

You should see the following message on the console:

$ Hello World! nucleo_h753zi

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b nucleo_h753zi samples/hello_world
west debug