CC1352R1 LaunchXL

Overview

The Texas Instruments CC1352R LaunchPad™ (LAUNCHXL-CC1352R1) is a development kit for the SimpleLink™ multi-Standard CC1352R wireless MCU.

See the TI CC1352R LaunchPad Product Page for details.

TI CC1352R LaunchPad

Texas Instruments CC1352R LaunchPad™

Hardware

The CC1352R LaunchPad™ development kit features the CC1352R wireless MCU. The board is equipped with two LEDs, two push buttons and BoosterPack connectors for expansion. It also includes an integrated (XDS110) debugger.

The CC13522 wireless MCU has a 48 MHz Arm® Cortex®-M4F SoC and an integrated Sub-1 and 2.4 GHz transceiver supporting multiple protocols including Bluetooth® Low Energy and IEEE® 802.15.4.

See the TI CC1352R Product Page for additional details.

Supported Features

The CC1352R LaunchPad board configuration supports the following hardware features:

Interface

Controller

Driver/Component

GPIO

on-chip

gpio

MPU

on-chip

arch/arm

NVIC

on-chip

arch/arm

PINMUX

on-chip

pinmux

UART

on-chip

serial

I2C

on-chip

i2c

SPI

on-chip

spi

WDT

on-chip

watchdog

AUX_ADC

on-chip

adc

HWINFO

on-chip

hwinfo

Other hardware features have not been enabled yet for this board.

Connections and IOs

All I/O signals are accessible from the BoosterPack connectors. Pin function aligns with the LaunchPad standard.

Pin

Function

Usage

DIO3

GPIO

DIO4

I2C_MSSCL

I2C SCL

DIO5

I2C_MSSDA

I2C SDA

DIO6

GPIO

Red LED

DIO7

GPIO

Green LED

DIO8

SSI0_RX

SPI MISO

DIO9

SSI0_TX

SPI MOSI

DIO10

SSI0_CLK

SPI CLK

DIO11

SSIO_CS

SPI CS

DIO12

UART0_RX

UART RXD

DIO13

UART0_TX

UART TXD

DIO14

GPIO

Button 2

DIO15

GPIO

Button 1

DIO16

JTAG TDO

DIO17

JTAG TDI

DIO18

UART0_RTS

UART RTS / JTAG SWO

DIO19

UART0_CTS

UART CTS

DIO20

GPIO

Flash CS

DIO21

GPIO

DIO22

GPIO

DIO23

AUX_IO

A0

DIO24

AUX_IO

A1

DIO25

AUX_IO

A2

DIO26

AUX_IO

A3

DIO27

AUX_IO

A4

DIO28

AUX_IO

A5

DIO29

AUX_IO

A6

DIO30

AUX_IO

A7

Programming and Debugging

Before flashing or debugging ensure the RESET, TMS, TCK, TDO, and TDI jumpers are in place. Also place jumpers on the TXD and RXD signals for a serial console using the XDS110 application serial port.

Prerequisites:

  1. Ensure the XDS-110 emulation firmware on the board is updated.

    Download and install the latest XDS-110 emulation package.

    Follow these xds110 firmware update directions

    Note that the emulation package install may place the xdsdfu utility in <install_dir>/ccs_base/common/uscif/xds110/.

  2. Install OpenOCD

    You can obtain OpenOCD by following these installing the latest Zephyr SDK instructions.

    After the installation, add the directory containing the OpenOCD executable to your environment’s PATH variable. For example, use this command in Linux:

    export PATH=$ZEPHYR_SDK_INSTALL_DIR/sysroots/x86_64-pokysdk-linux/usr/bin/openocd:$PATH
    

Flashing

Applications for the CC1352R LaunchPad board configuration can be built and flashed in the usual way (see Building an Application and Run an Application for more details).

Here is an example for the Hello World application.

First, run your favorite terminal program to listen for output.

$ screen <tty_device> 115200

Replace <tty_device> with the port where the XDS110 application serial device can be found. For example, /dev/ttyACM0.

Then build and flash the application in the usual way.

# From the root of the zephyr repository
west build -b cc1352r1_launchxl samples/hello_world
west flash

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b cc1352r1_launchxl samples/hello_world
west debug

Bootloader

The ROM bootloader on CC13x2 and CC26x2 devices is enabled by default. The bootloader will start if there is no valid application image in flash or the so-called backdoor is enabled (via option CONFIG_CC13X2_CC26X2_BOOTLOADER_BACKDOOR_ENABLE) and BTN-1 is held down during reset. See the bootloader documentation in chapter 10 of the TI CC13x2 / CC26x2 Technical Reference Manual for additional information.

Power Management and UART

System and device power management are supported on this platform, and can be enabled via the standard Kconfig options in Zephyr, such as CONFIG_PM, CONFIG_PM_DEVICE.

When system power management is turned on (CONFIG_PM=y), sleep state 2 (standby mode) is allowed, and polling is used to retrieve input by calling uart_poll_in(), it is possible for characters to be missed if the system enters standby mode between calls to uart_poll_in(). This is because the UART is inactive while the system is in standby mode. The workaround is to disable sleep state 2 while polling:

pm_policy_state_lock_get(PM_STATE_STANDBY, PM_ALL_SUBSTATES);
<code that calls uart_poll_in() and expects input at any point in time>
pm_policy_state_lock_put(PM_STATE_STANDBY, PM_ALL_SUBSTATES);

References

CC1352R1 LaunchPad Quick Start Guide:

http://www.ti.com/lit/pdf/swru525