.. _bluetooth_shell: Shell ##### The Bluetooth Shell is an application based on the :ref:`shell_api` module. It offer a collection of commands made to easily interact with the Bluetooth stack. Bluetooth Shell Setup and Usage ******************************* First you need to build and flash your board with the Bluetooth shell. For how to do that, see the :ref:`getting_started`. The Bluetooth shell itself is located in :zephyr_file:`tests/bluetooth/shell/`. When it's done, connect to the CLI using your favorite serial terminal application. You should see the following prompt: .. code-block:: console uart:~$ For more details on general usage of the shell, see :ref:`shell_api`. The first step is enabling Bluetooth. To do so, use the :code:`bt init` command. The following message is printed to confirm Bluetooth has been initialized. .. code-block:: console uart:~$ bt init Bluetooth initialized Settings Loaded [00:02:26.771,148] fs_nvs: nvs_mount: 8 Sectors of 4096 bytes [00:02:26.771,148] fs_nvs: nvs_mount: alloc wra: 0, fe8 [00:02:26.771,179] fs_nvs: nvs_mount: data wra: 0, 0 [00:02:26.777,984] bt_hci_core: hci_vs_init: HW Platform: Nordic Semiconductor (0x0002) [00:02:26.778,015] bt_hci_core: hci_vs_init: HW Variant: nRF52x (0x0002) [00:02:26.778,045] bt_hci_core: hci_vs_init: Firmware: Standard Bluetooth controller (0x00) Version 3.2 Build 99 [00:02:26.778,656] bt_hci_core: bt_init: No ID address. App must call settings_load() [00:02:26.794,738] bt_hci_core: bt_dev_show_info: Identity: EB:BF:36:26:42:09 (random) [00:02:26.794,769] bt_hci_core: bt_dev_show_info: HCI: version 5.3 (0x0c) revision 0x0000, manufacturer 0x05f1 [00:02:26.794,799] bt_hci_core: bt_dev_show_info: LMP: version 5.3 (0x0c) subver 0xffff Identities ********** Identities are a Zephyr host concept, allowing a single physical device to behave like multiple logical Bluetooth devices. The shell allows the creation of multiple identities, to a maximum that is set by the Kconfig symbol :kconfig:option:`CONFIG_BT_ID_MAX`. To create a new identity, use :code:`bt id-create` command. You can then use it by selecting it with its ID :code:`bt id-select `. Finally, you can list all the available identities with :code:`id-show`. Scan for devices **************** Start scanning by using the :code:`bt scan on` command. Depending on the environment you're in, you may see a lot of lines printed on the shell. To stop the scan, run :code:`bt scan off`, the scrolling should stop. Here is an example of what you can expect: .. code-block:: console uart:~$ bt scan on Bluetooth active scan enabled [DEVICE]: CB:01:1A:2D:6E:AE (random), AD evt type 0, RSSI -78 C:1 S:1 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff [DEVICE]: 20:C2:EE:59:85:5B (random), AD evt type 3, RSSI -62 C:0 S:0 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff [DEVICE]: E3:72:76:87:2F:E8 (random), AD evt type 3, RSSI -74 C:0 S:0 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff [DEVICE]: 1E:19:25:8A:CB:84 (random), AD evt type 3, RSSI -67 C:0 S:0 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff [DEVICE]: 26:42:F3:D5:A0:86 (random), AD evt type 3, RSSI -73 C:0 S:0 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff [DEVICE]: 0C:61:D1:B9:5D:9E (random), AD evt type 3, RSSI -87 C:0 S:0 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff [DEVICE]: 20:C2:EE:59:85:5B (random), AD evt type 3, RSSI -66 C:0 S:0 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff [DEVICE]: 25:3F:7A:EE:0F:55 (random), AD evt type 3, RSSI -83 C:0 S:0 D:0 SR:0 E:0 Prim: LE 1M, Secn: No packets, Interval: 0x0000 (0 us), SID: 0xff uart:~$ bt scan off Scan successfully stopped As you can see, this can lead to a high number of results. To reduce that number and easily find a specific device, you can enable scan filters. There are four types of filters: by name, by RSSI, by address and by periodic advertising interval. To apply a filter, use the :code:`bt scan-set-filter` command followed by the type of filters. You can add multiple filters by using the commands again. For example, if you want to look only for devices with the name *test shell*: .. code-block:: console uart:~$ bt scan-filter-set name "test shell" Or if you want to look for devices at a very close range: .. code-block:: console uart:~$ bt scan-filter-set rssi -40 RSSI cutoff set at -40 dB Finally, if you want to remove all filters: .. code-block:: console uart:~$ bt scan-filter-clear all You can use the command :code:`bt scan on` to create an *active* scanner, meaning that the scanner will ask the advertisers for more information by sending a *scan request* packet. Alternatively, you can create a *passive scanner* by using the :code:`bt scan passive` command, so the scanner will not ask the advertiser for more information. Connecting to a device ********************** To connect to a device, you need to know its address and type of address and use the :code:`bt connect` command with the address and the type as arguments. Here is an example: .. code-block:: console uart:~$ bt connect 52:84:F6:BD:CE:48 random Connection pending Connected: 52:84:F6:BD:CE:48 (random) Remote LMP version 5.3 (0x0c) subversion 0xffff manufacturer 0x05f1 LE Features: 0x000000000001412f LE PHY updated: TX PHY LE 2M, RX PHY LE 2M LE conn param req: int (0x0018, 0x0028) lat 0 to 42 LE conn param updated: int 0x0028 lat 0 to 42 You can list the active connections of the shell using the :code:`bt connections` command. The shell maximum number of connections is defined by :kconfig:option:`CONFIG_BT_MAX_CONN`. You can disconnect from a connection with the :code:`bt disconnect ` command. .. note:: If you were scanning just before, you can connect to the last scanned device by simply running the :code:`bt connect` command. Alternatively, you can use the :code:`bt connect-name ` command to automatically enable scanning with a name filter and connect to the first match. Advertising *********** Begin advertising by using the :code:`bt advertise on` command. This will use the default parameters and advertise a resolvable private address with the name of the device. You can choose to use the identity address instead by running the :code:`bt advertise on identity` command. To stop advertising use the :code:`bt advertise off` command. To enable more advanced features of advertising, you should create an advertiser using the :code:`bt adv-create` command. Parameters for the advertiser can be passed either at the creation of it or by using the :code:`bt adv-param` command. To begin advertising with this newly created advertiser, use the :code:`bt adv-start` command, and then the :code:`bt adv-stop` command to stop advertising. When using the custom advertisers, you can choose if it will be connectable or scannable. This leads to four options: :code:`conn-scan`, :code:`conn-nscan`, :code:`nconn-scan` and :code:`nconn-nscan`. Those parameters are mandatory when creating an advertiser or updating its parameters. For example, if you want to create a connectable and scannable advertiser and start it: .. code-block:: console uart:~$ bt adv-create conn-scan Created adv id: 0, adv: 0x200022f0 uart:~$ bt adv-start Advertiser[0] 0x200022f0 set started You may notice that with this, the custom advertiser does not advertise the device name; you need to enable it. Continuing from the previous example: .. code-block:: console uart:~$ bt adv-stop Advertiser set stopped uart:~$ bt adv-param conn-scan name uart:~$ bt adv-start Advertiser[0] 0x200022f0 set started You should now see the name of the device in the advertising data. You can also set the advertising data manually by using the :code:`bt adv-data` command. The following example shows how to set the advertiser name with it: .. code-block:: console uart:~$ bt adv-create conn-scan Created adv id: 0, adv: 0x20002348 uart:~$ bt adv-data 1009426C7565746F6F74682D5368656C6C uart:~$ bt adv-start Advertiser[0] 0x20002348 set started The data must be formatted according to the Bluetooth Core Specification (see version 5.3, vol. 3, part C, 11). In this example, the first octet is the size of the data (the data and one octet for the data type), the second one is the type of data, ``0x09`` is the Complete Local Name and the remaining data are the name in ASCII. So, on the other device you should see the name *Bluetooth-Shell*. When advertising, if others devices use an *active* scanner, you may receive *scan request* packets. To visualize those packets, you can add :code:`scan-reports` to the parameters of your advertiser. Directed Advertising ==================== It is possible to use directed advertising on the shell if you want to reconnect to a device. The following example demonstrates how to create a directed advertiser with the address specified right after the parameter :code:`directed`. The :code:`low` parameter indicates that we want to use the low duty cycle mode, and the :code:`dir-rpa` parameter is required if the remote device is privacy-enabled and supports address resolution of the target address in directed advertisement. .. code-block:: console uart:~$ bt adv-create conn-scan directed D7:54:03:CE:F3:B4 random low dir-rpa Created adv id: 0, adv: 0x20002348 After that, you can start the advertiser and then the target device will be able to reconnect. Extended Advertising ==================== Let's now have a look at some extended advertising features. To enable extended advertising, use the `ext-adv` parameter. .. code-block:: console uart:~$ bt adv-create conn-nscan ext-adv name-ad Created adv id: 0, adv: 0x200022f0 uart:~$ bt adv-start Advertiser[0] 0x200022f0 set started This will create an extended advertiser, that is connectable and non-scannable. Encrypted Advertising Data ========================== Zephyr has support for the Encrypted Advertising Data feature. The :code:`bt encrypted-ad` sub-commands allow managing the advertising data of a given advertiser. To encrypt the advertising data, key materials need to be provided, that can be done with :code:`bt encrypted-ad set-keys `. The session key is 16 bytes long and the initialisation vector is 8 bytes long. You can add advertising data by using :code:`bt encrypted-ad add-ad` and :code:`bt encrypted-ad add-ead`. The former will take add one advertising data structure (as defined in the Core Specification), when the later will read the given data, encrypt them and then add the generated encrypted advertising data structure. It's possible to mix encrypted and non-encrypted data, when done adding advertising data, :code:`bt encrypted-ad commit-ad` can be used to apply the change to the data to the selected advertiser. After that the advertiser can be started as described previously. It's possible to clear the advertising data by using :code:`bt encrypted-ad clear-ad`. On the Central side, it's possible to decrypt the received encrypted advertising data by setting the correct keys material as described earlier and then enabling the decrypting of the data with :code:`bt encrypted-ad decrypt-scan on`. .. note:: To see the advertising data in the scan report :code:`bt scan-verbose-output` need to be enabled. .. note:: It's possible to increase the length of the advertising data by increasing the value of :kconfig:option:`CONFIG_BT_CTLR_ADV_DATA_LEN_MAX` and :kconfig:option:`CONFIG_BT_CTLR_SCAN_DATA_LEN_MAX`. Here is a simple example demonstrating the usage of EAD: .. tabs:: .. group-tab:: Peripheral .. code-block:: console uart:~$ bt init ... uart:~$ bt adv-create conn-nscan ext-adv Created adv id: 0, adv: 0x81769a0 uart:~$ bt encrypted-ad set-keys 9ba22d3824efc70feb800c80294cba38 2e83f3d4d47695b6 session key set to: 00000000: 9b a2 2d 38 24 ef c7 0f eb 80 0c 80 29 4c ba 38 |..-8$... ....)L.8| initialisation vector set to: 00000000: 2e 83 f3 d4 d4 76 95 b6 |.....v.. | uart:~$ bt encrypted-ad add-ad 06097368656C6C uart:~$ bt encrypted-ad add-ead 03ffdead03ffbeef uart:~$ bt encrypted-ad commit-ad Advertising data for Advertiser[0] 0x81769a0 updated. uart:~$ bt adv-start Advertiser[0] 0x81769a0 set started .. group-tab:: Central .. code-block:: console uart:~$ bt init ... uart:~$ bt scan-verbose-output on uart:~$ bt encrypted-ad set-keys 9ba22d3824efc70feb800c80294cba38 2e83f3d4d47695b6 session key set to: 00000000: 9b a2 2d 38 24 ef c7 0f eb 80 0c 80 29 4c ba 38 |..-8$... ....)L.8| initialisation vector set to: 00000000: 2e 83 f3 d4 d4 76 95 b6 |.....v.. | uart:~$ bt encrypted-ad decrypt-scan on Received encrypted advertising data will now be decrypted using provided key materials. uart:~$ bt scan on Bluetooth active scan enabled [DEVICE]: 68:49:30:68:49:30 (random), AD evt type 5, RSSI -59 shell C:1 S:0 D:0 SR:0 E:1 Prim: LE 1M, Secn: LE 2M, Interval: 0x0000 (0 us), SID: 0x0 [SCAN DATA START - EXT_ADV] Type 0x09: shell Type 0x31: Encrypted Advertising Data: 0xe2, 0x17, 0xed, 0x04, 0xe7, 0x02, 0x1d, 0xc9, 0x40, 0x07, uart:~0x18, 0x90, 0x6c, 0x4b, 0xfe, 0x34, 0xad [START DECRYPTED DATA] Type 0xff: 0xde, 0xad Type 0xff: 0xbe, 0xef [END DECRYPTED DATA] [SCAN DATA END] ... Filter Accept List ****************** It's possible to create a list of allowed addresses that can be used to connect to those addresses automatically. Here is how to do it: .. code-block:: console uart:~$ bt fal-add 47:38:76:EA:29:36 random uart:~$ bt fal-add 66:C8:80:2A:05:73 random uart:~$ bt fal-connect on The shell will then connect to the first available device. In the example, if both devices are advertising at the same time, we will connect to the first address added to the list. The Filter Accept List can also be used for scanning or advertising by using the option :code:`fal`. For example, if we want to scan for a bunch of selected addresses, we can set up a Filter Accept List: .. code-block:: console uart:~$ bt fal-add 65:4B:9E:83:AF:73 random uart:~$ bt fal-add 73:72:82:B4:8F:B9 random uart:~$ bt fal-add 5D:85:50:1C:72:64 random uart:~$ bt scan on fal You should see only those three addresses reported by the scanner. Enabling security ***************** When connected to a device, you can enable multiple levels of security, here is the list for Bluetooth LE: * **1** No encryption and no authentication; * **2** Encryption and no authentication; * **3** Encryption and authentication; * **4** Bluetooth LE Secure Connection. To enable security, use the :code:`bt security ` command. For levels requiring authentication (level 3 and above), you must first set the authentication method. To do it, you can use the :code:`bt auth all` command. After that, when you will set the security level, you will be asked to confirm the passkey on both devices. On the shell side, do it with the command :code:`bt auth-passkey-confirm`. Pairing ======= Enabling authentication requires the devices to be bondable. By default the shell is bondable. You can make the shell not bondable using :code:`bt bondable off`. You can list all the devices you are paired with using the command :code:`bt bonds`. The maximum number of paired devices is set using :kconfig:option:`CONFIG_BT_MAX_PAIRED`. You can remove a paired device using :code:`bt clear ` or remove all paired devices with the command :code:`bt clear all`. GATT **** The following examples assume that you have two devices already connected. To perform service discovery on the client side, use the :code:`gatt discover` command. This should print all the services that are available on the GATT server. On the server side, you can register pre-defined test services using the :code:`gatt register` command. When done, you should see the newly added services on the client side when running the discovery command. You can now subscribe to those new services on the client side. Here is an example on how to subscribe to the test service: .. code-block:: console uart:~$ gatt subscribe 26 25 Subscribed The server can now notify the client with the command :code:`gatt notify`. Another option available through the GATT command is initiating the MTU exchange. To do it, use the :code:`gatt exchange-mtu` command. To update the shell maximum MTU, you need to update Kconfig symbols in the configuration file of the shell. For more details, see :ref:`bluetooth_mtu_update_sample`. L2CAP ***** The :code:`l2cap` command exposes parts of the L2CAP API. The following example shows how to register a LE PSM, connect to it from another device and send 3 packets of 14 octets each. The example assumes that the two devices are already connected. On device A, register the LE PSM: .. code-block:: console uart:~$ l2cap register 29 L2CAP psm 41 sec_level 1 registered On device B, connect to the registered LE PSM and send data: .. code-block:: console uart:~$ l2cap connect 29 Chan sec: 1 L2CAP connection pending Channel 0x20000210 connected Channel 0x20000210 status 1 uart:~$ l2cap send 3 14 Rem 2 Rem 1 Rem 0 Outgoing data channel 0x20000210 transmitted Outgoing data channel 0x20000210 transmitted Outgoing data channel 0x20000210 transmitted On device A, you should have received the data: .. code-block:: console Incoming conn 0x20002398 Channel 0x20000210 status 1 Channel 0x20000210 connected Channel 0x20000210 requires buffer Incoming data channel 0x20000210 len 14 00000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff |........ ...... | Channel 0x20000210 requires buffer Incoming data channel 0x20000210 len 14 00000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff |........ ...... | Channel 0x20000210 requires buffer Incoming data channel 0x20000210 len 14 00000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff |........ ...... | Logging ******* You can configure the logging level per module at runtime. This depends on the maximum logging level that is compiled in. To configure, use the :code:`log` command. Here are some examples: * List the available modules and their current logging level .. code-block:: console uart:~$ log status * Disable logging for *bt_hci_core* .. code-block:: console uart:~$ log disable bt_hci_core * Enable error logs for *bt_att* and *bt_smp* .. code-block:: console uart:~$ log enable err bt_att bt_smp * Disable logging for all modules .. code-block:: console uart:~$ log disable * Enable warning logs for all modules .. code-block:: console uart:~$ log enable wrn