:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: nxp,imx-mipi-dsi
.. _dtbinding_nxp_imx_mipi_dsi:

nxp,imx-mipi-dsi
################

Vendor: :ref:`NXP Semiconductors <dt_vendor_nxp>`

Description
***********

These nodes are "mipi-dsi" bus nodes.

.. code-block:: none

   NXP MCUX MIPI DSI

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``nxp,lcdif``
           - ``phandle``
           - .. code-block:: none

                Instance of the LCDIF peripheral. Only required when using the MIPI DSI in video mode.


         * - ``dpi-color-coding``
           - ``string``
           - .. code-block:: none

                MIPI DPI interface color coding. Sets the distribution of RGB bits within the 24-bit d bus, as specified by the DPI specification.


             Legal values: ``'16-bit-config-1'``, ``'16-bit-config-2'``, ``'16-bit-config-3'``, ``'18-bit-config-1'``, ``'18-bit-config-2'``, ``'24-bit'``

         * - ``dpi-pixel-packet``
           - ``string``
           - .. code-block:: none

                MIPI DSI pixel packet type send through DPI interface.


             Legal values: ``'16-bit'``, ``'18-bit'``, ``'18-bit-loose'``, ``'24-bit'``

         * - ``dpi-video-mode``
           - ``string``
           - .. code-block:: none

                DPI video mode.


             Legal values: ``'non-burst-sync-pulse'``, ``'non-burst-sync-event'``, ``'burst'``

         * - ``dpi-bllp-mode``
           - ``string``
           - .. code-block:: none

                Behavior in BLLP (Blanking or Low-Power Interval).


             Legal values: ``'low-power'``, ``'blank'``, ``'null'``

         * - ``autoinsert-eotp``
           - ``boolean``
           - .. code-block:: none

                Automatically insert an EoTp short packet when switching from HS to LP mode.


         * - ``dphy-ref-frequency``
           - ``int``
           - .. code-block:: none

                Maximum clock speed supported by the device, in Hz.


             This property is **required**.

         * - ``phy-clock``
           - ``int``
           - .. code-block:: none

                MIPI PHY clock frequency. Should be set to ensure clock frequency is at least (pixel clock * bits per output pixel) / number of mipi data lanes




   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nxp,imx-mipi-dsi" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


             This property is **required**.

             Constant value: ``1``

         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


             This property is **required**.

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.