:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: panasonic,reduced-arduino-header
.. _dtbinding_panasonic_reduced_arduino_header:

panasonic,reduced-arduino-header
################################

Vendor: :ref:`Panasonic Corporation <dt_vendor_panasonic>`

Description
***********



.. code-block:: none

   Panasonic's reduced Arduino header.

                                 D15    21
                                 D14    20
                                 AREF   -
                                 GND    -
       -   N/C                   D13    19
       -   IOREF                 D12    18
       -   RESET                 D11    17
       -   3V3                   D10    16
       -   5V                    D9     NC
       -   GND                   D8     NC
       -   GND
       -   VIN                   D7     NC
                                 D6     NC
       0   A0                    D5     11
       1   A1                    D4     10
       2   A2                    D3     9
       3   A3                    D2     8
       NC  A4                    D1     7
       NC  A5                    D0     6

   Panasonic's reduced Arduino header is based on the Arduino UNO layout
   and provides four different headers. The main difference is that some
   pins are not available due to the lack of pins on the Panasonic module.
   These unconnected pins are labeled "NC" in the mapping above.

   So:

   1. Power Supply header exactly, like on Arduino UNO layout.

   2. Analog Input header, like on Arduino UNO layout, but A4 and A5 are
   not connected.

   3. 8-pin header (opposite Analog Input).  Digital input signals, like on
   Arduino UNO layout, labeled from D0 at the bottom to D7 at the top, but D6
   and D7 are not connected.

   4. 10-pin header (opposite Power Supply). Digital input signals, like on
   Arduino UNO layout, labeled from D8 at the bottom through D15 at the top,
   but D8 and D9 are not connected.

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``gpio-map``
           - ``compound``
           - This property is **required**.

         * - ``gpio-map-mask``
           - ``compound``
           - 

         * - ``gpio-map-pass-thru``
           - ``compound``
           - 

         * - ``#gpio-cells``
           - ``int``
           - .. code-block:: none

                Number of items to expect in a GPIO specifier


             This property is **required**.



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "panasonic,reduced-arduino-header" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.