:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: mikro-bus
.. _dtbinding_mikro_bus:

mikro-bus
#########

Vendor: :ref:`Generic or vendor-independent <dt_no_vendor>`

Description
***********



.. code-block:: none

   GPIO pins exposed on Mikro BUS headers.

   The Mikro BUS layout provides two headers, aligned on the opposite
   edges of the board.

   Documentation:
   https://www.mikroe.com/mikrobus
   https://download.mikroe.com/documents/standards/mikrobus/mikrobus-standard-specification-v200.pdf

   This binding provides a nexus mapping for 10 pins, left side pins are
   numbered 0 - 5 (AN - MOSI), the right side pins are numbered 6 - 10
   (PWM - SDA). The bottom 2 pins on each side are used for input voltage
   and ground, they are not mapped in the nexus.

                          Analog - AN     PWM - PWM output
                           Reset - RST    INT - Hardware Interrupt
                 SPI Chip Select - CS      RX - UART Receive
                       SPI Clock - SCK     TX - UART Transmit
   SPI Master Input Slave Output - MISO   SCL - I2C Clock
   SPI Master Output Slave Input - MOSI   SDA - I2C Data
                  VCC-3.3V power - +3.3V  +5V - VCC-5V power
                Reference Ground - GND    GND - Reference Ground

   Board's silkscreen may vary depending on your board, but coherent with
   the description above as it's according to the standard's specification.

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``gpio-map``
           - ``compound``
           - This property is **required**.

         * - ``gpio-map-mask``
           - ``compound``
           - 

         * - ``gpio-map-pass-thru``
           - ``compound``
           - 

         * - ``#gpio-cells``
           - ``int``
           - .. code-block:: none

                Number of items to expect in a GPIO specifier


             This property is **required**.



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "mikro-bus" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.