:orphan:
.. raw:: html
.. dtcompatible:: nordic,nrf-led-matrix
.. _dtbinding_nordic_nrf_led_matrix:
nordic,nrf-led-matrix
#####################
Vendor: :ref:`Nordic Semiconductor `
Description
***********
.. code-block:: none
Generic LED matrix driven by nRF SoC GPIOs
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``row-gpios``
- ``phandle-array``
- .. code-block:: none
Array of GPIOs to be used as rows of the matrix.
This property is **required**.
* - ``col-gpios``
- ``phandle-array``
- .. code-block:: none
Array of GPIOs to be used as columns of the matrix.
This property is **required**.
* - ``pixel-mapping``
- ``uint8-array``
- .. code-block:: none
Array of bytes that specify which rows and columns of the matrix
control its particular pixels, line by line. Each byte in this
array corresponds to one pixel of the matrix and specifies the row
index in the high nibble and the column index in the low nibble.
For example, the following snippet (from the bbc_microbit board DTS):
width = <5>;
height = <5>;
pixel-mapping = [00 13 01 14 02
23 24 25 26 27
...
specifies that:
- pixel (0,0) is controlled by row 0 and column 0
- pixel (1,0) is controlled by row 1 and column 3
- pixel (0,1) is controlled by row 2 and column 3
- pixel (1,1) is controlled by row 2 and column 4
and so on.
This property is **required**.
* - ``refresh-frequency``
- ``int``
- .. code-block:: none
Frequency of refreshing the matrix, in Hz.
This property is **required**.
* - ``timer``
- ``phandle``
- .. code-block:: none
Reference to a TIMER instance for controlling refreshing of the matrix.
This property is **required**.
* - ``pwm``
- ``phandle``
- .. code-block:: none
Reference to a PWM instance for generating pulse signals on column
GPIOs. If not provided, GPIOTE and PPI channels are allocated and
used instead for generating those pulses.
* - ``pixel-group-size``
- ``int``
- .. code-block:: none
This value specifies the maximum number of LEDs in one row that can
be lit simultaneously.
If set to 1, only a single LED is turned on in a particular time slot.
Bigger values increase the maximum achievable brightness of the LEDs
and lower the CPU load by decreasing the frequency of execution of
the timer interrupt handler.
In case GPIOTE and PPI channels are used for generating the pixel pulse
signals, the number of channels that need to be allocated is equal to
this value.
If GPIOTE and PPI channels are used, the upper limit for the value is
defined by the number of CC channels in the used timer minus one.
If PWM is used, the upper limit is the number of PWM channels.
This property is **required**.
* - ``height``
- ``int``
- .. code-block:: none
Height of the panel driven by the controller, with the units in pixels.
This property is **required**.
* - ``width``
- ``int``
- .. code-block:: none
Width of the panel driven by the controller, with the units in pixels.
This property is **required**.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "nordic,nrf-led-matrix" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`dt-important-props` for more information.
* - ``reg``
- ``array``
- .. code-block:: none
register space
See :ref:`dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
See :ref:`dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
See :ref:`dt-important-props` for more information.
This property is **deprecated**.
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``power-domain``
- ``phandle``
- .. code-block:: none
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
* - ``zephyr,pm-device-runtime-auto``
- ``boolean``
- .. code-block:: none
Automatically configure the device for runtime power management after the
init function runs.