.. _mimxrt1160_evk: NXP MIMXRT1160-EVK ################## Overview ******** The dual core i.MX RT1160 runs on the Cortex-M7 core at 600 MHz and on the Cortex-M4 at 240 MHz. The i.MX RT1160 MCU offers support over a wide temperature range and is qualified for consumer, industrial and automotive markets. .. image:: ../../../../../../../../../zephyr/boards/arm/mimxrt1160_evk/doc/mimxrt1160_evk.jpg :align: center :alt: MIMXRT1160-EVK Hardware ******** - MIMXRT1166DVM6A MCU - 600MHz Cortex-M7 & 240Mhz Cortex-M4 - 2MB SRAM with 512KB of TCM for Cortex-M7 and 256KB of TCM for Cortex-M4 - Memory - 512 Mbit SDRAM - 128 Mbit QSPI Flash - 512 Mbit Octal Flash - TF socket for SD card - Display - MIPI LCD connector - Ethernet - 10/100 Mbit/s Ethernet PHY - 10/100/1000 Mbit/s Ethernet PHY - USB - USB 2.0 OTG connector - USB 2.0 host connector - Audio - 3.5 mm audio stereo headphone jack - Board-mounted microphone - Left and right speaker out connectors - Power - 5 V DC jack - Debug - JTAG 20-pin connector - OpenSDA with DAPLink - Sensor - MIPI camera sensor connector - Expansion port - Arduino interface - CAN bus connector For more information about the MIMXRT1160 SoC and MIMXRT1160-EVK board, see these references: - `i.MX RT1160 Website`_ - `i.MX RT1160 Datasheet`_ - `i.MX RT1160 Reference Manual`_ - `MIMXRT1160-EVK Website`_ - `MIMXRT1160-EVK Board Hardware User's Guide`_ External Memory =============== This platform has the following external memories: +--------------------+------------+-------------------------------------+ | Device | Controller | Status | +====================+============+=====================================+ | W9825G6KH | SEMC | Enabled via device configuration | | | | data block, which sets up SEMC at | | | | boot time | +--------------------+------------+-------------------------------------+ | IS25WP128 | FLEXSPI | Enabled via flash configurationn | | | | block, which sets up FLEXSPI at | | | | boot time. | +--------------------+------------+-------------------------------------+ Supported Features ================== The mimxrt1160_evk board configuration supports the hardware features listed below. For additional features not yet supported, please also refer to the :ref:`mimxrt1170_evk` , which is the superset board in NXP's i.MX RT11xx family. NXP prioritizes enabling the superset board with NXP's Full Platform Support for Zephyr. Therefore, the mimxrt1170_evk board may have additional features already supported, which can also be re-used on this mimxrt1160_evk board: +-----------+------------+-------------------------------------+ | Interface | Controller | Driver/Component | +===========+============+=====================================+ | NVIC | on-chip | nested vector interrupt controller | +-----------+------------+-------------------------------------+ | SYSTICK | on-chip | systick | +-----------+------------+-------------------------------------+ | GPIO | on-chip | gpio | +-----------+------------+-------------------------------------+ | COUNTER | on-chip | counter | +-----------+------------+-------------------------------------+ | UART | on-chip | serial port-polling; | | | | serial port-interrupt | +-----------+------------+-------------------------------------+ | SPI | on-chip | spi | +-----------+------------+-------------------------------------+ | I2C | on-chip | i2c | +-----------+------------+-------------------------------------+ | ADC | on-chip | adc | +-----------+------------+-------------------------------------+ | CAN | on-chip | flexcan | +-----------+------------+-------------------------------------+ | WATCHDOG | on-chip | watchdog | +-----------+------------+-------------------------------------+ | PWM | on-chip | pwm | +-----------+------------+-------------------------------------+ | DMA | on-chip | dma | +-----------+------------+-------------------------------------+ | GPT | on-chip | gpt | +-----------+------------+-------------------------------------+ | USB | on-chip | USB Device | +-----------+------------+-------------------------------------+ | HWINFO | on-chip | Unique device serial number | +-----------+------------+-------------------------------------+ | CAAM RNG | on-chip | entropy | +-----------+------------+-------------------------------------+ | FLEXSPI | on-chip | flash programming | +-----------+------------+-------------------------------------+ The default configuration can be found in the defconfig file: ``boards/arm/mimxrt1160_evk/mimxrt1160_evk_cm7_defconfig`` Other hardware features are not currently supported by the port. Connections and I/Os ==================== The MIMXRT1160 SoC has six pairs of pinmux/gpio controllers. +---------------+-----------------+---------------------------+ | Name | Function | Usage | +===============+=================+===========================+ | WAKEUP | GPIO | SW7 | +---------------+-----------------+---------------------------+ | GPIO_AD_04 | GPIO | LED | +---------------+-----------------+---------------------------+ | GPIO_AD_24 | LPUART1_TX | UART Console | +---------------+-----------------+---------------------------+ | GPIO_AD_25 | LPUART1_RX | UART Console | +---------------+-----------------+---------------------------+ | GPIO_LPSR_00 | CAN3_TX | flexcan | +---------------+-----------------+---------------------------+ | GPIO_LPSR_01 | CAN3_RX | flexcan | +---------------+-----------------+---------------------------+ | GPIO_AD_29 | SPI1_CS0 | spi | +---------------+-----------------+---------------------------+ | GPIO_AD_28 | SPI1_CLK | spi | +---------------+-----------------+---------------------------+ | GPIO_AD_30 | SPI1_SDO | spi | +---------------+-----------------+---------------------------+ | GPIO_AD_31 | SPI1_SDI | spi | +---------------+-----------------+---------------------------+ | GPIO_AD_08 | LPI2C1_SCL | i2c | +---------------+-----------------+---------------------------+ | GPIO_AD_09 | LPI2C1_SDA | i2c | +---------------+-----------------+---------------------------+ | GPIO_LPSR_05 | LPI2C5_SCL | i2c | +---------------+-----------------+---------------------------+ | GPIO_LPSR_04 | LPI2C5_SDA | i2c | +---------------+-----------------+---------------------------+ | GPIO_AD_04 | FLEXPWM1_PWM2 | pwm | +---------------+-----------------+---------------------------+ Dual Core samples ***************** +-----------+------------------+----------------------------+ | Core | Boot Address | Comment | +===========+==================+============================+ | Cortex M7 | 0x30000000[630K] | primary core | +-----------+------------------+----------------------------+ | Cortex M4 | 0x20020000[96k] | boots from OCRAM | +-----------+------------------+----------------------------+ +----------+------------------+-----------------------+ | Memory | Address[Size] | Comment | +==========+==================+=======================+ | flexspi1 | 0x30000000[16M] | Cortex M7 flash | +----------+------------------+-----------------------+ | sdram0 | 0x80030000[64M] | Cortex M7 ram | +----------+------------------+-----------------------+ | ocram | 0x20020000[512K] | Cortex M4 "flash" | +----------+------------------+-----------------------+ | sram1 | 0x20000000[128K] | Cortex M4 ram | +----------+------------------+-----------------------+ | ocram2 | 0x200C0000[512K] | Mailbox/shared memory | +----------+------------------+-----------------------+ Only the first 16K of ocram2 has the correct MPU region attributes set to be used as shared memory System Clock ============ The MIMXRT1160 SoC is configured to use SysTick as the system clock source, running at 600MHz. When targeting the M4 core, SysTick will also be used, running at 240MHz When power management is enabled, the 32 KHz low frequency oscillator on the board will be used as a source for the GPT timer to generate a system clock. This clock enables lower power states, at the cost of reduced resolution Serial Port =========== The MIMXRT1160 SoC has 12 UARTs. One is configured for the console and the remaining are not used. Programming and Debugging ************************* Build and flash applications as usual (see :ref:`build_an_application` and :ref:`application_run` for more details). Building a Dual-Core Image ========================== Dual core samples load the M4 core image from flash into the shared ``ocram`` region. The M7 core then sets the M4 boot address to this region. The only sample currently enabled for dual core builds is the ``openamp`` sample. To flash a dual core sample, the M4 image must be flashed first, so that it is written to flash. Then, the M7 image must be flashed. The openamp sysbuild sample will do this automatically by setting the image order. The secondary core can be debugged normally in single core builds (where the target is ``mimxrt1160_evk_cm4``). For dual core builds, the secondary core should be placed into a loop, then a debugger can be attached (see `AN13264`_, section 4.2.3 for more information) Configuring a Debug Probe ========================= A debug probe is used for both flashing and debugging the board. This board is configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`, however the :ref:`pyocd-debug-host-tools` do not yet support programming the external flashes on this board so you must reconfigure the board for one of the following debug probes instead. .. _Using J-Link RT1160: Using J-Link --------------------------------- Install the :ref:`jlink-debug-host-tools` and make sure they are in your search path. There are two options: the onboard debug circuit can be updated with Segger J-Link firmware, or :ref:`jlink-external-debug-probe` can be attached to the EVK. See `Using J-Link with MIMXRT1160-EVK or MIMXRT1170-EVK`_ for more details. Configuring a Console ===================== Regardless of your choice in debug probe, we will use the OpenSDA microcontroller as a usb-to-serial adapter for the serial console. Check that jumpers J5 and J8 are **on** (they are on by default when boards ship from the factory) to connect UART signals to the OpenSDA microcontroller. Connect a USB cable from your PC to J11. Use the following settings with your serial terminal of choice (minicom, putty, etc.): - Speed: 115200 - Data: 8 bits - Parity: None - Stop bits: 1 Flashing ======== Here is an example for the :ref:`hello_world` application. Before power on the board, make sure SW1 is set to 0001b .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: mimxrt1160_evk_cm7 :goals: flash Power off the board, and change SW1 to 0010b. Then power on the board and open a serial terminal, reset the board (press the SW4 button), and you should see the following message in the terminal: .. code-block:: console ***** Booting Zephyr OS v2.6.0-xxxx-xxxxxxxxxxxxx ***** Hello World! mimxrt1160_evk_cm7 Debugging ========= Here is an example for the :ref:`hello_world` application. .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: mimxrt1160_evk_cm7 :goals: debug Open a serial terminal, step through the application in your debugger, and you should see the following message in the terminal: .. code-block:: console ***** Booting Zephyr OS v2.4.0-xxxx-xxxxxxxxxxxxx ***** Hello World! mimxrt1160_evk_cm7 .. _MIMXRT1160-EVK Website: https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1160-evaluation-kit:MIMXRT1160-EVK .. _MIMXRT1160-EVK Board Hardware User's Guide: https://www.nxp.com/webapp/Download?colCode=UM11617 .. _i.MX RT1160 Website: https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/i-mx-rt-crossover-mcus/i-mx-rt1160-crossover-mcu-family-high-performance-mcu-with-arm-cortex-m7-and-cortex-m4-cores:i.MX-RT1160 .. _i.MX RT1160 Datasheet: https://www.nxp.com/docs/en/data-sheet/IMXRT1160CEC.pdf .. _i.MX RT1160 Reference Manual: https://www.nxp.com/webapp/Download?colCode=IMXRT1160RM .. _Using J-Link with MIMXRT1160-EVK or MIMXRT1170-EVK: https://community.nxp.com/t5/i-MX-RT-Knowledge-Base/Using-J-Link-with-MIMXRT1160-EVK-or-MIMXRT1170-EVK/ta-p/1529760 .. _AN13264: https://www.nxp.com/docs/en/application-note/AN13264.pdf Experimental ENET Driver ======================== Current default ethernet driver is eth_mcux, with binding `nxp,kinetis-ethernet`. There is a new driver with binding `nxp,enet`, which is experimental and undergoing development, but will have enhanced capability, such as not hardcoding code for only one phy in the driver like eth_mcux. To build for this EVK with the new driver, include the experimental overlay to west build with the option `-DEXTRA_DTC_OVERLAY_FILE=nxp,enet-experimental.overlay`.