.. _mimx8mq_evk: NXP MIMX8MQ EVK ############### Overview ******** i.MX8MQ EVK board is based on NXP i.MX8MQ applications processor, composed of a quad Cortex®-A53 cluster and a single Cortex®-M4 core. Zephyr OS is ported to run on the Cortex®-M4 core. - Board features: - RAM: 3GB LPDDR4 - Storage: - 16GB eMMC5.0 - 32MB QSPI NOR - microSD Socket - Wireless: - WiFi: 2.4/5GHz IEEE 802.11 a/b/g/n/ac - Bluetooth: v4.1 - USB: - OTG - 1x type C - HOST - 1x type A - Ethernet - PCI-E M.2 - LEDs: - 1x Power status LED - 1x UART LED - Debug - JTAG 10-pin connector - MicroUSB for UART debug, two COM ports for A53 and M4 .. image:: ../../../../../../../../../zephyr/boards/arm/mimx8mq_evk/doc/img/mimx8mq_evk.jpg :align: center :alt: MIMX8MQ EVK More information about the board can be found at the `NXP website`_. Supported Features ================== The Zephyr mimx8mq_evk board configuration supports the following hardware features: +-----------+------------+-------------------------------------+ | Interface | Controller | Driver/Component | +===========+============+=====================================+ | NVIC | on-chip | nested vector interrupt controller | +-----------+------------+-------------------------------------+ | SYSTICK | on-chip | systick | +-----------+------------+-------------------------------------+ | CLOCK | on-chip | clock_control | +-----------+------------+-------------------------------------+ | PINMUX | on-chip | pinmux | +-----------+------------+-------------------------------------+ | UART | on-chip | serial port-polling; | | | | serial port-interrupt | +-----------+------------+-------------------------------------+ The default configuration can be found in the defconfig file: :zephyr_file:`boards/arm/mimx8mq_evk/mimx8mq_evk_cm4_defconfig`. Other hardware features are not currently supported by the port. Connections and IOs =================== MIMX8MQ EVK board was tested with the following pinmux controller configuration. +---------------+-----------------+---------------------------+ | Board Name | SoC Name | Usage | +===============+=================+===========================+ | UART2 RXD | UART2_TXD | UART Console | +---------------+-----------------+---------------------------+ | UART2 TXD | UART2_RXD | UART Console | +---------------+-----------------+---------------------------+ System Clock ============ The M4 Core is configured to run at a 266 MHz clock speed. Serial Port =========== The i.MX8MQ SoC has four UARTs. UART_2 is configured for the console and the remaining are not used/tested. Programming and Debugging ************************* The MIMX8MQ EVK board doesn't have QSPI flash for the M4 and it needs to be started by the A53 core. The A53 core is responsible to load the M4 binary application into the RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer, and get the M4 out of reset. The A53 can perform these steps at bootloader level or after the Linux system has booted. The M4 can use up to 3 different RAMs. These are the memory mapping for A53 and M4: +------------+-------------------------+------------------------+-----------------------+----------------------+ | Region | Cortex-A53 | Cortex-M4 (System Bus) | Cortex-M4 (Code Bus) | Size | +============+=========================+========================+=======================+======================+ | OCRAM | 0x00900000-0x0091FFFF | 0x20200000-0x2021FFFF | 0x00900000-0x0091FFFF | 128KB | +------------+-------------------------+------------------------+-----------------------+----------------------+ | TCMU | 0x00800000-0x0081FFFF | 0x20000000-0x2001FFFF | | 128KB | +------------+-------------------------+------------------------+-----------------------+----------------------+ | TCML | 0x007E0000-0x007FFFFF | | 0x1FFE0000-0x1FFFFFFF | 128KB | +------------+-------------------------+------------------------+-----------------------+----------------------+ | OCRAM_S | 0x00180000-0x00187FFF | 0x20180000-0x20187FFF | 0x00180000-0x00187FFF | 32KB | +------------+-------------------------+------------------------+-----------------------+----------------------+ For more information about memory mapping see the `i.MX 8M Applications Processor Reference Manual`_ (section 2.1.2 and 2.1.3) At compilation time you have to choose which RAM will be used. This configuration is done in the file ``boards/arm/mimx8mq_evk/mimx8mq_evk_cm4.dts`` with "zephyr,flash" (when CONFIG_XIP=y) and "zephyr,sram" properties. The available configurations are: .. code-block:: none "zephyr,flash" - &tcml_code - &ocram_code - &ocram_s_code "zephyr,sram" - &tcmu_sys - &ocram_sys - &ocram_s_sys Load and run Zephyr on M4 from A53 using u-boot. .. tabs:: .. group-tab:: From an SD card Copy the compiled ``zephyr.bin`` to the first FAT partition of the SD card and plug the SD card into the board. Power it up and stop the u-boot execution at prompt. Load the M4 binary onto the desired memory and start its execution using: .. code-block:: console fatload mmc 0:1 0x40480000 zephyr.bin cp.b 0x40480000 0x7e0000 0x8000 bootaux 0x7e0000 .. group-tab:: From serial This procedure requires ``screen`` and ``lrzsz`` to be installed. Start ``screen``, power up the board, and stop the u-boot execution at prompt: .. code-block:: console screen 115200 Start ``loadx`` with offset ``7e0000``: .. code-block:: console loadx 7e0000 115200 Send the compiled ``zephyr.bin`` with ``sx`` by pressing :kbd:`Ctrl-a` followed by :kbd:`:` and write: .. code-block:: console exec !! sx Start execution: .. code-block:: console bootaux 0x7e0000 Debugging ========= MIMX8MQ EVK board can be debugged by connecting an external JLink JTAG debugger to the J401 debug connector and to the PC. Then the application can be debugged using the usual way. Here is an example for the :ref:`hello_world` application. .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: mimx8mq_evk_cm4 :goals: debug Open a serial terminal, step through the application in your debugger, and you should see the following message in the terminal: .. code-block:: console ***** Booting Zephyr OS build zephyr-v2.6.99-30942-g6ee70bd22058 ***** Hello World! mimx8mq_evk_cm4 References ========== .. _NXP website: https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-applications-processor:MCIMX8M-EVK .. _i.MX 8M Applications Processor Reference Manual: https://www.nxp.com/webapp/Download?colCode=IMX8MDQLQRM