Enhanced ShockBurst (ESB)

This user guide describes what Enhanced ShockBurst (ESB) is and how to use it with an nRF5 Series device.

Enhanced ShockBurst (ESB) is a basic protocol supporting two-way data packet communication including packet buffering, packet acknowledgment, and automatic retransmission of lost packets. ESB provides radio communication with low power consumption, and the implementation is small in code size and easy to use.

The ESB protocol was embedded in hardware in the legacy nRF24L Series. The Enhanced ShockBurst module enables an nRF5 Series device to communicate with an nRF5 or nRF24L Series device using the ESB protocol.

ESB features automatic packet transaction handling for easy implementation of a reliable bidirectional data link. A transaction is a packet exchange between two transceivers, with one transceiver acting as the Primary Receiver (PRX) and the other transceiver acting as the Primary Transmitter (PTX).

Enhanced ShockBurst network

Enhanced ShockBurst network

Features

  • Supports a star network topology with typically one Primary Receiver (PRX) and up to 8 Primary Transmitters (PTX)

  • 1 to 32 bytes dynamic payload length in legacy mode

  • 1 to 252 bytes static payload length between nRF5 Series devices

  • Bidirectional data transfer between each PTX and the PRX

  • Packet acknowledgment and automatic packet retransmission functionality

  • Individual TX and RX FIFOs for every pipe

  • Backward compatible with legacy nRF24Lxx Enhanced ShockBurst

  • Support for external front-end modules.

Resources

ESB requires exclusive access to all fixed and configured resources for the Enhanced ShockBurst library to ensure correct operation:

Resource type

Resource

Required

Radio

NRF_RADIO

fixed

Timer

NRF_TIMER2

configurable

DPPI/PPI channels

6 channels

automatically allocated

Event generator unit

NRF_EGU0 events 6 - 7

fixed

Software interrupt

0

fixed

Note

There is no MPU enforcement of this exclusive access, so manipulating these resources gives undefined behavior.

The radio and timer interrupt handlers run at priority level 0 (highest level), and the ESB callback functions run at priority level 1. Other interrupts used by the application must use priority level 2 or lower (level 2 to 7) to ensure correct operation.

ESB requires the MPSL library for front-end module support. This library is always linked into the build, however, it is not initialized by default to provide your application and the ESB protocol with access to all hardware resources. See Direct support for more details.

Backward compatibility

The Enhanced ShockBurst library is compatible with the legacy nRFgo SDK. To ensure that your application built with the nRF Connect SDK can communicate with nRF24 devices that run applications built with the nRFgo SDK, use the configuration ESB_LEGACY_CONFIG.

Note, however, that the provided samples in the two SDKs do not correspond, so that you cannot use the Transmitter sample from one SDK with the Receiver sample from the other SDK.

Packet transaction

An Enhanced ShockBurst packet transaction is initiated by a packet transmission from the PTX and successfully completed when the PTX has received an acknowledgment packet (ACK packet) from the PRX.

To enable a bidirectional data link, the PRX is allowed to attach a data payload to the ACK packet. To do so, the PRX adds a packet to its TX FIFO, which is sent as the payload in the next ACK packet.

PTX to PRX packet transaction

PTX to PRX packet transaction

If the PTX does not receive the ACK after the initial transmitted packet, it attempts to retransmit the packet until the ACK is finally being received. The maximum number of allowed retransmission attempts and the delay between each attempt is specified by the most recent call to either esb_init() (where the values of esb_config.retransmit_count and esb_config.retransmit_delay in the esb_config structure specify the number of retransmission attempts and the delay between them, respectively) or the functions esb_set_retransmit_count() and esb_set_retransmit_delay(). The retransmission delay is defined as the duration between the start of each transmission attempt. Note that this differs from the legacy nRF24L Series hardware implementation, where the delay was defined as the duration from the end of a packet transmission until the start of the retransmission.

If the ACK packet sent from the PRX to the PTX is lost, but both the initial packet and the subsequent retransmission attempts are being successfully received by the PRX, the repeated packets will be discarded by the PRX. This prevents the PRX application from receiving duplicate packets. However, repeated packets will always be ACKed by the PRX, even though they are being discarded.

Failed package transaction

Failed package transaction

A PTX can select that individual packets that are transmitted to the PRX do not require an ACK to be sent in return from the PRX. This decision is taken by the application when uploading a packet to the TX FIFO using the esb_payload.noack field of the esb_payload parameter that is passed to the esb_write_payload() function.

When the PRX receives a packet that does not require an ACK, it does not send an ACK packet to the PTX, and as a result the PTX will continue retransmitting the packet until the maximum number of allowed retransmission attempts is reached.

Setting up an ESB application

Perform the following steps to set up an application to send and receive packets:

  1. Initialize ESB using esb_init(). You can use the default parameters in ESB_DEFAULT_CONFIG as starting point for the p_config parameter and reconfigure them if needed.

  2. If necessary, use any of the following functions to update the addresses, the address prefix, the channel, and the bitrate:

  3. Make sure that the high-frequency clock is running:

    NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
    NRF_CLOCK->TASKS_HFCLKSTART = 1;
    while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);
    
  4. Start sending or receiving packets:

To stop the ESB module, call esb_disable(). Note, however, that if a transaction is ongoing when you disable the module, it is not completed. Therefore, you might want to check if the module is idle before disabling it.

Frequency selection

ESB can send or receive packets using any of the channels that the nRF5 chip can use. The channel is selected by calling the esb_set_rf_channel() function.

The PTX and PRX must be configured to use the same frequency to exchange packets.

Pipes and addressing

Each logical address on the nodes is termed a pipe. Each pipe maps to one on-air address that is used when transmitting or receiving packets.

The on-air addresses are composed of a 2-4 byte long base address in addition to a 1 byte prefix address. Note that the nRF5 radio uses an alternating sequence of 0 and 1 as the preamble of the packet. Therefore, for packets to be received correctly, the most significant byte of the base address must not be an alternating sequence of 0 and 1, that is, it must not be 0x55 or 0xAA.

Pipe 0 has its own unique base address (base address 0), while pipes 1-7 use the same base address (base address 1). Each of the 8 pipes have a unique byte-long prefix address.

On-air, the most significant bit of each address byte is transmitted first. The most significant byte of the 2-4 byte long base address is the first transmitted address byte, while the prefix byte is transmitted last.

Addresses cannot consist of a 0x00 prefix and an address on the format 0x00XXXXXX (length 4)/0x0000XXXX (length 5). Such a zero address will cause error code NRF_ERROR_INVALID_PARAM to be returned.

Note that the byte ordering in ESB and the nRF5 radio peripheral are not the same, because the address bytes are rearranged in ESB to match the nRF24L radios.

Address part of an ESB packet

Address part of an ESB packet

Packet identification

Any packet that is transmitted from a PTX to a PRX is uniquely identified by a two-bit packet ID field (PID) in the packet header together with the packet’s Cyclic Redundancy Check (CRC) field. This packet ID is used to distinguish a new packet from the previous packet if it has the same payload.

At the PRX, retransmitted packets are discarded and not added to an RX FIFO. The ESB_EVENT_RX_RECEIVED event is not called.

The CRC is used in addition to the PID to identify a unique packet. This reduces the likelihood of a packet being falsely identified as a retransmission attempt and discarded by the PRX when several consecutive failed packet transmission attempts occur. This feature is helpful as the PID is only two bits.

FIFOs

On each node, there is one FIFO queue for RX and one for TX. The FIFOs are shared by all pipes, and esb_payload.pipe indicates a packet’s pipe. For received packets, this field specifies from which pipe the packet came. For transmitted packets, it specifies through which pipe the packet will be sent.

When multiple packets are queued, they are handled in a FIFO fashion, ignoring pipes.

PTX FIFO handling

When ESB is enabled in PTX mode, any packets that are uploaded to a TX FIFO will be transmitted at the next opportunity.

When an ACK is successfully received from a PRX, the PTX assumes that the payload was successfully received and added to the PRX’s RX FIFO. The successfully transmitted packet is removed from the TX FIFO, so that the next packet in the FIFO can be transmitted.

If an ACK received by a PTX contains a payload, this payload is added to the PTX’s RX FIFO.

PRX FIFO handling

When ESB is enabled in PRX mode, all enabled pipes (addresses) are simultaneously monitored for incoming packets.

If a new packet that was not previously added to the PRX’s RX FIFO is received, and RX FIFO has available space for the packet, the packet is added to the RX FIFO and an ACK is sent in return to the PTX. If the TX FIFO contains any packets, the next serviceable packet in the TX FIFO is attached as a payload in the ACK packet. Note that this TX packet must have been uploaded to the TX FIFO before the packet is received.

Event handling

When there is an event on the radio, the Enhanced ShockBurst module analyzes its cause and, if necessary, queues an event to the application. This event indicates a successful operation, a failed operation, or new data available in the RX FIFO.

Events are queued as flags that are read out on the first opportunity to trigger a software interrupt. Therefore, there might be multiple radio interrupts between each event that is actually sent to the application. A single ESB_EVENT_TX_SUCCESS or ESB_EVENT_TX_FAILED event indicates one or more successful or failed operations, respectively. An ESB_EVENT_RX_RECEIVED event indicates that there is at least one new packet in the RX FIFO. The event handler should make sure to completely empty the RX FIFO when appropriate.

Front-end module support

The ESB protocol supports external front-end modules. See Working with RF front-end modules for more details.

Errata workarounds and nRF52832 chip revisions

The module implementation on nRF52832 devices include a set of workarounds for hardware erratas. These erratas require a few hundred bytes of code space to determine runtime which workarounds are applicable to the device running the firmware. This is to ensure that firmware based on newer SDKs function as intended on both older and newer revision chips. If you know that your firmware will only on certain devices, you may save a few hundred bytes of code space by removing the workaround. If you are sure that you do not require support for revision 1 chips, you may remove all code blocks within if statements on the format if((NRF_FICR->INFO.VARIANT & 0x0000FF00) == 0x00004200). If you are sure that you do not require support for revision 2 chips, you may remove all code blocks within if statements on the format if((NRF_FICR->INFO.VARIANT & 0x0000FF00) == 0x00004500).

Examples

The nRF Connect SDK provides the following example application that shows how to use the ESB protocol: