ti,lmp90077 (on spi bus)

Vendor: Texas Instruments

Description

These nodes are “lmp90xxx” bus nodes.

Texas Instruments LMP90077 AFE binding

Properties

Top level properties

These property descriptions apply to “ti,lmp90077” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

Name

Type

Details

drdyb-gpios

phandle-array

Data Ready Bar

#io-channel-cells

int

This property is required.

Constant value: 2

spi-max-frequency

int

Maximum clock frequency of device's SPI interface in Hz

This property is required.

duplex

int

Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0    SPI_FULL_DUPLEX
  2048 SPI_HALF_DUPLEX

Legal values: 0, 2048

frame-format

int

Motorola or TI frame format. By default it's always Motorola's,
thus 0 as this is, by far, the most common format.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0     SPI_FRAME_FORMAT_MOTOROLA
  32768 SPI_FRAME_FORMAT_TI

Legal values: 0, 32768

supply-gpios

phandle-array

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

Child node properties

Name

Type

Details

reg

array

Channel identifier.

This property is required.

See Important properties for more information.

zephyr,gain

string

Gain selection:
- ADC_GAIN_1_6: x 1/6
- ADC_GAIN_1_5: x 1/5
- ADC_GAIN_1_4: x 1/4
- ADC_GAIN_1_3: x 1/3
- ADC_GAIN_2_5: x 2/5
- ADC_GAIN_1_2: x 1/2
- ADC_GAIN_2_3: x 2/3
- ADC_GAIN_4_5: x 4/5
- ADC_GAIN_1:   x 1
- ADC_GAIN_2:   x 2
- ADC_GAIN_3:   x 3
- ADC_GAIN_4:   x 4
- ADC_GAIN_6:   x 6
- ADC_GAIN_8:   x 8
- ADC_GAIN_12:  x 12
- ADC_GAIN_16:  x 16
- ADC_GAIN_24:  x 24
- ADC_GAIN_32:  x 32
- ADC_GAIN_64:  x 64
- ADC_GAIN_128: x 128

This property is required.

Legal values: 'ADC_GAIN_1_6', 'ADC_GAIN_1_5', 'ADC_GAIN_1_4', 'ADC_GAIN_1_3', 'ADC_GAIN_2_5', 'ADC_GAIN_1_2', 'ADC_GAIN_2_3', 'ADC_GAIN_4_5', 'ADC_GAIN_1', 'ADC_GAIN_2', 'ADC_GAIN_3', 'ADC_GAIN_4', 'ADC_GAIN_6', 'ADC_GAIN_8', 'ADC_GAIN_12', 'ADC_GAIN_16', 'ADC_GAIN_24', 'ADC_GAIN_32', 'ADC_GAIN_64', 'ADC_GAIN_128'

zephyr,reference

string

Reference selection:
- ADC_REF_VDD_1:     VDD
- ADC_REF_VDD_1_2:   VDD/2
- ADC_REF_VDD_1_3:   VDD/3
- ADC_REF_VDD_1_4:   VDD/4
- ADC_REF_INTERNAL:  Internal
- ADC_REF_EXTERNAL0: External, input 0
- ADC_REF_EXTERNAL1: External, input 1

This property is required.

Legal values: 'ADC_REF_VDD_1', 'ADC_REF_VDD_1_2', 'ADC_REF_VDD_1_3', 'ADC_REF_VDD_1_4', 'ADC_REF_INTERNAL', 'ADC_REF_EXTERNAL0', 'ADC_REF_EXTERNAL1'

zephyr,vref-mv

int

This property can be used to specify the voltage (in millivolts)
of the reference selected for this channel, so that applications
can get that value if needed for some calculations.
For the internal reference, the voltage can be usually obtained with
a dedicated ADC API call, so there is no need to use this property
in that case, but for other references this property can be useful.

zephyr,acquisition-time

int

Acquisition time.
Use the ADC_ACQ_TIME macro to compose the value for this property
or pass ADC_ACQ_TIME_DEFAULT to use the default setting for a given
hardware (e.g. when the hardware does not allow to configure the
acquisition time).

This property is required.

zephyr,input-positive

int

Positive ADC input. Used only for drivers that select
the ADC_CONFIGURABLE_INPUTS Kconfig option.

zephyr,input-negative

int

Negative ADC input. Used only for drivers that select
the ADC_CONFIGURABLE_INPUTS Kconfig option.
When specified, the channel is to be used in differential input mode,
otherwise, single-ended mode is used.

zephyr,resolution

int

ADC resolution to be used for the channel.

zephyr,oversampling

int

Oversampling setting to be used for the channel.
When specified, each sample is averaged from 2^N conversion results
(where N is the provided value).

Specifier cell names

  • io-channel cells: positive, negative