CAF: Power manager module¶
The power manager module of the Common Application Framework (CAF) is responsible for reducing the energy consumption of battery-powered devices. The module achieves this reduction by switching to low power modes when the device is not used for a longer period of time.
You can enable the power manager module by selecting the
CONFIG_CAF_POWER_MANAGER option in the configuration.
This module uses Zephyr’s Power Management subsystem.
CONFIG_CAF_POWER_MANAGER_TIMEOUT configuration option, you can set the period of time after which the application enters the low power mode.
By default, the timeout is set to 120 seconds.
CONFIG_CAF_POWER_MANAGER_ERROR_TIMEOUT sets the period of time after which the device is turned off upon an internal error.
The power manager module is started when the “main” is ready (which is reported using
When started, it can do the following operations:
Manage Power states
Trigger Switching to low power
Handle Wake-up scenarios from suspended or off states
The application can be in the following power states:
The power manager module takes control of the overall operating system power state. See the following section for more details about how the application states converts to the system power state.
In this state, the board power management is left totally to the operating system. The peripherals can be turned on, including LEDs.
The application remains in this state indefinitely if any of the modules has restricted the allowed power level to
If no module blocks other power states, the power-down counter is active. On timeout, the power manager module sets the application to either the suspended or the off state. There are some events that reset the power-down counter:
Upon power-down timeout, the power manager module switches the application to the suspended state if there is at least one module that restricts power-down levels to
POWER_MANAGER_LEVEL_SUSPENDED and there is no module that restricts power below level to any higher state (
The other modules of the application, if applicable, will turn off the peripherals or switch them to standby to conserve power.
The operating system is kept in the
It is assumed that the operating system will conserve power by setting the CPU state to idle whenever possible. The established connection is maintained.
Upon power-down timeout, the power manager module switches the application to the deep sleep mode if no module restricts it.
This means that all the modules are restricted to
If applicable, the other modules of the application turn off the peripherals or switch them to standby to conserve power.
The operating system switches to the
The devices are suspended and the CPU is switched to the deep sleep (off) mode.
A device reboot is required to exit this state.
The power manager module checks if any application modules have reported an error condition.
When any application module switches to the error state (that is, broadcasts
module_state_event), the power manager module puts the application into the error state.
Then, after the period of time defined by
CONFIG_CAF_POWER_MANAGER_ERROR_TIMEOUT, it puts the application to the off state.
During this period, other modules can report the error condition to the user (for example, CAF: LEDs module can keep working in the error state).
Any registered module can restrict the power state allowed by the usage of
It provides the module ID and the deepest allowed power state.
The power manager module uses flags to restrict modes for any module.
This means that you can repeatedly send the
When the power manager module detects that the application is about to enter the low power state (either suspended or off), it sends a
Other application modules react to this event by changing their configuration to low power, for example by turning off LEDs.
Some modules might not be ready to switch to the lower power state.
In such case, the module that is not yet ready should consume the
power_down_event and change its internal state, so that it enters the low power state when ready.
After entering the low power state, each module must report this by sending a
The power manager module continues with the low power state change when it gets a notification that the module switched to the low power.
Only after all modules confirmed that they have entered the low power state (by not consuming the
power_down_event), the power manager module sets the required application’s state.
If a disconnection happens while the device is in the suspended state, the power manager module switches the application to the off state.
However, the application can also be configured to keep the system in the suspended state when there are no active connections, instead of switching to the off state.
To select this behavior, use the
CONFIG_CAF_POWER_MANAGER_STAY_ON configuration option.
The application can be woken up in the following scenarios:
Wake-up from the suspended state¶
Any module can trigger the application to switch from the suspended state back to the idle state by submitting a
This is normally done on some external event, for example upon interaction from the user of the device.
The application modules receive a
wake_up_event, which switches them back to the normal operation.
The power manager module sets the application to the idle state.
This also restarts the power-down counter if the device is not connected through USB.
Wake-up from the off state¶
In the off state, the CPU is not running and the CPU reboot is required.
Before the application enters the off state, at least one module must configure the peripheral under its control, so that it issues a hardware-related event capable of rebooting the CPU (that is, capable of leaving the CPU off mode). After the reboot, the application initializes itself again.