semtech,sx1509b (on i2c bus)

Vendor: Semtech Corporation

Description

SX1509B GPIO node

Properties

Properties not inherited from the base binding file.

Name

Type

Details

#gpio-cells

int

Number of items to expect in a GPIO specifier

This property is required.

Constant value: 2

ngpios

int

This property indicates the number of in-use slots of available slots
for GPIOs. The typical example is something like this: the hardware
register is 32 bits wide, but only 18 of the bits have a physical
counterpart. The driver is generally written so that all 32 bits can
be used, but the IP block is reused in a lot of designs, some using
all 32 bits, some using 18 and some using 12. In this case, setting
"ngpios = <18>;" informs the driver that only the first 18 GPIOs, at
local offset 0 .. 17, are in use.  For cases in which there might be
holes in the slot range, this value should be the max slot number-1.

This property is required.

Default value: 32

Constant value: 16

nint-gpios

phandle-array

Connection for the NINT signal. This signal is active-low when
produced by sx1509b GPIO node.

init-out-low

int

Bit mask identifying pins that should be initialized as outputs
driven low.

init-out-high

int

Bit mask identifying pins that should be initialized as outputs
driven high.

supply-gpios

phandle

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

gpio-controller

boolean

Convey's this node is a GPIO controller

This property is required.

gpio-reserved-ranges

array

If not all the GPIOs at offsets 0...N-1 are usable for ngpios = <N>, then
this property contains an additional set of tuples which specify which GPIOs
are unusable. This property indicates the start and size of the GPIOs
that can't be used.

For example, setting "gpio-reserved-ranges = <3 2>, <10 1>;" means that
GPIO offsets 3, 4, and 10 are not usable, even if ngpios = <18>.

gpio-line-names

string-array

This is an array of strings defining the names of the GPIO lines
going out of the GPIO controller

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “semtech,sx1509b” compatible.

Name

Type

Details

label

string

Human readable string describing the device (used as device_get_binding() argument)

This property is required.

See Important properties for more information.

reg

array

register space

This property is required.

See Important properties for more information.

status

string

indicates the operational status of a device

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

compatible strings

This property is required.

See Important properties for more information.

reg-names

string-array

name of each register space

interrupts

array

interrupts for device

See Important properties for more information.

interrupts-extended

compound

extended interrupt specifier for device

interrupt-names

string-array

name of each interrupt

interrupt-parent

phandle

phandle to interrupt controller node

clocks

phandle-array

Clock gate information

clock-names

string-array

name of each clock

#address-cells

int

number of address cells in reg property

#size-cells

int

number of size cells in reg property

dmas

phandle-array

DMA channels specifiers

dma-names

string-array

Provided names of DMA channel specifiers

io-channels

phandle-array

IO channels specifiers

io-channel-names

string-array

Provided names of IO channel specifiers

Specifier cell names

  • gpio cells: pin, flags