semtech,sx1262 (on spi bus)

Vendor: Semtech Corporation

Description

Semtech SX1262 LoRa Modem

Properties

Properties not inherited from the base binding file.

Name

Type

Details

reset-gpios

phandle-array

GPIO connected to the modem's NRST signal.

This signal is open-drain, active-low as interpreted by the
modem.

This property is required.

busy-gpios

phandle-array

GPIO connected to the modem's BUSY signal.

This property is required.

antenna-enable-gpios

phandle-array

Antenna power enable pin.

tx-enable-gpios

phandle-array

Antenna switch TX enable GPIO. If set, the driver tracks the
state of the radio and controls the RF switch.

rx-enable-gpios

phandle-array

Antenna switch RX enable GPIO. If set, the driver tracks the
state of the radio and controls the RF switch.

dio1-gpios

phandle-array

GPIO connected to DIO1. This GPIO will be used as a generic
IRQ line from the chip.

This property is required.

dio2-tx-enable

boolean

Use DIO2 to drive an RF switch selecting between the TX and RX
paths. When enabled, DIO2 goes high when the chip is
transmitting.

dio3-tcxo-voltage

int

TCXO supply voltage controlled by DIO3 if present.

See constants in dt-bindings/lora/sx126x.h.

tcxo-power-startup-delay-ms

int

Startup delay to let the TCXO stabilize after TCXO power on.

spi-max-frequency

int

Maximum clock frequency of device's SPI interface in Hz

This property is required.

supply-gpios

phandle

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “semtech,sx1262” compatible.

Name

Type

Details

reg

array

register space

This property is required.

See Important properties for more information.

label

string

Human readable string describing the device (used as device_get_binding() argument)

This property is required.

See Important properties for more information.

status

string

indicates the operational status of a device

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

compatible strings

This property is required.

See Important properties for more information.

reg-names

string-array

name of each register space

interrupts

array

interrupts for device

See Important properties for more information.

interrupts-extended

compound

extended interrupt specifier for device

interrupt-names

string-array

name of each interrupt

interrupt-parent

phandle

phandle to interrupt controller node

clocks

phandle-array

Clock gate information

clock-names

string-array

name of each clock

#address-cells

int

number of address cells in reg property

#size-cells

int

number of size cells in reg property

dmas

phandle-array

DMA channels specifiers

dma-names

string-array

Provided names of DMA channel specifiers

io-channels

phandle-array

IO channels specifiers

io-channel-names

string-array

Provided names of IO channel specifiers